Phono stages and cartridges
Matching a phono stage to a cartridge
A phono stage has to give the cartridge the gain it needs and the load it wants. Here is how to work both out, with the sums for every cartridge and every phono stage we carry.
What a phono stage does
A cartridge produces a very small signal, from about 6 thousandths of a volt for a strong moving magnet down to 2 ten-thousandths for a low-output moving coil. A phono stage does three things with it. It raises it to the level your amplifier expects. It restores the tonal balance the record was cut with, which is the RIAA equalization. And it presents the cartridge with an electrical load.
Equalization is the same for every cartridge. Gain and load are not, and those are the two things to match.
Gain
Makers quote a cartridge's output in millivolts at a standard test level. Among the cartridges we carry, moving magnets run from 2.5 to 6.5 mV, high-output moving coils from 2 to 2.5 mV, and moving coils from 0.2 to 0.8 mV.
Gain is quoted in decibels, and each figure is a multiplier: 40 dB multiplies the signal by 100, 60 dB by 1,000, 66 dB by about 2,000 and 70 dB by about 3,160. The sum is one multiplication.
level out = cartridge output × gain
A 5 mV moving magnet into 40 dB gives 500 mV. A 0.4 mV moving coil into 60 dB gives 400 mV, and into 66 dB about 800 mV.
We aim for 300 to 600 mV. Records are cut with peaks several times the test level, so that puts a loud passage in the region of the 2 volts a CD player or streamer delivers, and the turntable plays about as loud as your other sources.
Gold 300 mV to 1 VSilver 200 to 300 mV, or 1 to 2 VBronze 125 to 200 mV, or 2 to 3 VMaker's own pairing designed and sold together, shown without a medal
- Gold: 300 mV to 1 V. The volume control sits where it does for your other sources and noise stays out of the way.
- Silver: 200 to 300 mV, or 1 to 2 V. A little quiet or a little hot. Nothing is wrong; the volume control sits higher or lower than usual.
- Bronze: 125 to 200 mV, or 2 to 3 V. It will play. At the low end you may hear hiss in quiet passages, and at the high end a loud record can press the next input.
- Outside: too little gain sounds quiet and noisy, and too much can overload on loud passages.
Where a stage has several gain settings we show the one that lands nearest 500 mV. A maker's own cartridge on its own phono stage is shown with its figures and without a medal, as with tonearms. Rega, for one, sets its moving coils to the higher of its two gains.
Load
Moving coils are loaded with a resistance, in ohms. Start with the cartridge maker's recommendation. Where there is none, a load of ten times the cartridge's internal impedance or more is the usual starting point, and the final setting is made by ear. As a rule, too low a load dulls the top of the range and too high a load can leave it bright.
Moving magnets and high-output moving coils use the standard 47 kΩ input. What varies is capacitance, which includes the tonearm cable. Makers give a range: Ortofon asks for 150 to 300 pF for its 2M series, Sumiko for 100 to 200 pF.
In the tables, the load shown for each pairing is the setting on that phono stage nearest the maker's recommendation. An asterisk means the nearest setting falls outside it.
Which input
- A moving-magnet input suits moving magnets and high-output moving coils such as the Hana SH and MH, the Benz Micro Glider SH and the Sumiko Songbird High.
- A moving-coil input suits everything below about 1 mV.
- One-job stages. Rega's Fono Mini A2D and Fono MM are for moving magnets only. Rega's Fono MC and Aos MC, and Linn's Urika, are for moving coils only.
- Transformer inputs. Luxman's E-250 has two moving-coil inputs, high and low, chosen by the cartridge's output and impedance.
- Balanced inputs. A cartridge is a balanced source, and several stages accept it on XLR: Boulder, Burmester, the MOON 610LP and 810LP, Clearaudio's Balance V2, Luxman's E-07, the Accuphase C-57 and Linn's Uphorik.
- Optical cartridges from DS Audio do not use a phono stage. Each works with a DS Audio equalizer. DS Audio at Pearl Audio.
Price
A phono stage and a cartridge should be of a kind. On each phono stage's page we list the cartridges priced from about a quarter of the stage's price to one and a half times it, with the maker's own cartridges first. It is a rule of thumb. A modest stage will play a great cartridge without showing all it can do, and a great stage will not make a modest cartridge into something else.
One more rule of ours concerns output. Under about $3,000 we do not recommend a phono stage for a cartridge below 0.35 mV, even when it has a moving coil input. Under $1,000 we do not recommend one for a cartridge below 0.5 mV. A very low-output moving coil needs a quieter stage than those prices buy. A maker's own cartridge and phono stage, designed together, are the exception.
And a cartridge below 0.3 mV calls for a phono stage of $6,000 or more. Those are the only stages we list for it.
How we choose at Pearl
- MOON is the line we choose most often. The 110LP v2, 310LP, 610LP and 810LP cover moving magnets and moving coils alike, with the gain and load settings to follow a change of cartridge.
- Rega phono stages go with Rega. Rega engineers each phono stage to a price, and a stage gives the most for that price with a Rega cartridge ahead of it. Rega makes its Nd moving magnets and its moving coils by hand in its own factory in England and winds the coils there, so cartridge and phono stage are designed, and built, with each other in mind. We find that a Rega phono stage with a Rega cartridge is usually among the best-performing combinations at its price. The two also share one voice, cut from one cloth, much as a Luxman system does. So we recommend Rega's phono stages only with Rega turntables and Rega cartridges.
- A Luxman system gets a Luxman phono stage. We feel Luxman's phono stages work well with other makers' electronics. In a Luxman system, though, with a Luxman turntable and, in many cases, Luxman's own LMC-5 moving coil, which we think is superb value, we strongly encourage a Luxman phono stage: the freestanding E-250 or E-07, or the excellent phono stage built into a Luxman integrated amplifier, each of which has moving-magnet and moving-coil inputs. Tonally, Luxman's phono stages sit extremely well with Luxman's integrated amplifiers, preamplifiers and power amplifiers.
Cartridge by cartridge
For each cartridge: its output, its internal impedance, the load its maker asks for, and the gain that brings it to 300 to 600 mV.
Linn5 cartridges: output, load and the gain to look for
| Cartridge | Price | Output | Internal impedance | Maker's load | Gain to look for | Input |
|---|---|---|---|---|---|---|
| Adikt MM | $923 | 6.5 mV | not published | 47 kΩ | 33 to 39 dB | Moving-magnet input |
| Koil | $1,250 | 0.4 mV | not published | 100 Ω | 58 to 64 dB | Moving-coil input |
| Krystal | $2,415 | 0.5 mV | not published | 50 to 200 Ω | 56 to 62 dB | Moving-coil input |
| Kendo | $4,370 | 0.45 mV | not published | 100 Ω | 56 to 62 dB | Moving-coil input |
| Ekstatik | $8,335 | 0.45 mV | not published | 100 Ω | 56 to 62 dB | Moving-coil input |
Clearaudio15 cartridges: output, load and the gain to look for
| Cartridge | Price | Output | Internal impedance | Maker's load | Gain to look for | Input |
|---|---|---|---|---|---|---|
| Concept MM V2 | $350 | 3.3 mV | 660 Ω | 47 kΩ | 39 to 45 dB | Moving-magnet input |
| Performer V2 Ebony MM | $500 | 3.3 mV | 660 Ω | 47 kΩ | 39 to 45 dB | Moving-magnet input |
| Artist V2 Ebony MM | $700 | 3.6 mV | 660 Ω | 47 kΩ | 38 to 44 dB | Moving-magnet input |
| Jubilee Panzerholz MM | $1,000 | 3.6 mV | 660 Ω | 47 kΩ | 38 to 44 dB | Moving-magnet input |
| Concept MC | $1,350 | 0.4 mV | 11 Ω | 110 Ω or more (ten times its impedance) | 58 to 64 dB | Moving-coil input |
| Virtuoso V2 Ebony MM | $1,350 | 3.6 mV | 660 Ω | 47 kΩ | 38 to 44 dB | Moving-magnet input |
| Maestro V2 Ebony MM | $1,500 | 3.6 mV | 660 Ω | 47 kΩ | 38 to 44 dB | Moving-magnet input |
| Talisman Gold V2.1 MC | $2,700 | 0.5 mV | 50 Ω | 500 Ω or more (ten times its impedance) | 56 to 62 dB | Moving-coil input |
| Charisma V2.1 MM | $2,800 | 3.6 mV | 660 Ω | 47 kΩ | 38 to 44 dB | Moving-magnet input |
| Concerto V2.1 MC | $4,200 | 0.5 mV | 50 Ω | 500 Ω or more (ten times its impedance) | 56 to 62 dB | Moving-coil input |
| Stradivari V2.1 MC | $5,500 | 0.5 mV | 50 Ω | 500 Ω or more (ten times its impedance) | 56 to 62 dB | Moving-coil input |
| Jubilee Panzerholz V2.1 MC | $7,500 | 0.5 mV | 50 Ω | 500 Ω or more (ten times its impedance) | 56 to 62 dB | Moving-coil input |
| Da Vinci V2.1 MC | $9,000 | 0.5 mV | 50 Ω | 500 Ω or more (ten times its impedance) | 56 to 62 dB | Moving-coil input |
| Titanium V2.1 MC | $13,000 | 0.5 mV | 50 Ω | 500 Ω or more (ten times its impedance) | 56 to 62 dB | Moving-coil input |
| Goldfinger Statement V2.1 MC | $21,000 | 0.6 mV | 50 Ω | 500 Ω or more (ten times its impedance) | 54 to 60 dB | Moving-coil input |
Rega9 cartridges: output, load and the gain to look for
| Cartridge | Price | Output | Internal impedance | Maker's load | Gain to look for | Input |
|---|---|---|---|---|---|---|
| Carbon MM | $95 | 2.5 mV | not published | 47 kΩ | 42 to 48 dB | Moving-magnet input |
| Nd3 MM | $345 | 6 mV | not published | 47 kΩ | 34 to 40 dB | Moving-magnet input |
| Nd5 MM | $545 | 6 mV | not published | 47 kΩ | 34 to 40 dB | Moving-magnet input |
| Nd7 MM | $795 | 6 mV | not published | 47 kΩ | 34 to 40 dB | Moving-magnet input |
| Ania MC | $895 | 0.35 mV | 10 Ω | 100 Ω | 59 to 65 dB | Moving-coil input |
| Nd9 MM | $1,045 | 6 mV | not published | 47 kΩ | 34 to 40 dB | Moving-magnet input |
| Ania Pro MC | $1,225 | 0.35 mV | 10 Ω | 100 Ω | 59 to 65 dB | Moving-coil input |
| Apheta 3 MC | $2,245 | 0.35 mV | 10 Ω | 100 Ω | 59 to 65 dB | Moving-coil input |
| Aphelion 2 MC | $5,545 | 0.35 mV | 10 Ω | 100 Ω | 59 to 65 dB | Moving-coil input |
Benz Micro12 cartridges: output, load and the gain to look for
| Cartridge | Price | Output | Internal impedance | Maker's load | Gain to look for | Input |
|---|---|---|---|---|---|---|
| Glider SL | $2,100 | 0.4 mV | 12 Ω | 100 Ω or more | 58 to 64 dB | Moving-coil input |
| Glider SM | $2,100 | 0.8 mV | 24 Ω | 1 kΩ or more | 51 to 58 dB | Moving-coil input |
| Glider SH | $2,100 | 2.5 mV | 95 Ω | 47 kΩ | 42 to 48 dB | Moving-magnet input |
| Zebra Wood M | $2,600 | 0.8 mV | 24 Ω | 100 Ω or more | 51 to 58 dB | Moving-coil input |
| Zebra Wood H | $2,600 | 2.5 mV | 95 Ω | 47 kΩ | 42 to 48 dB | Moving-magnet input |
| Zebra Wood L | $2,600 | 0.4 mV | 12 Ω | 100 Ω or more | 58 to 64 dB | Moving-coil input |
| Reference S | $3,200 | 0.26 mV | 3.5 Ω | 50 Ω or more | 61 to 67 dB | Moving-coil input, high gain |
| Gullwing SLR | $4,200 | 0.34 mV | 40 Ω | 500 Ω or more | 59 to 65 dB | Moving-coil input |
| Gullwing SHR | $4,200 | 0.7 mV | not published | 400 Ω or more | 53 to 59 dB | Moving-coil input |
| Ruby ZL | $4,800 | 0.34 mV | 38 Ω | 500 Ω or more | 59 to 65 dB | Moving-coil input |
| Ruby ZH | $4,800 | 0.7 mV | not published | 400 Ω or more | 53 to 59 dB | Moving-coil input |
| LP-S | $6,000 | 0.34 mV | 38 Ω | 500 Ω or more | 59 to 65 dB | Moving-coil input |
Hana10 cartridges: output, load and the gain to look for
| Cartridge | Price | Output | Internal impedance | Maker's load | Gain to look for | Input |
|---|---|---|---|---|---|---|
| EH | $475 | 2 mV | 130 Ω | 47 kΩ | 44 to 50 dB | Moving-magnet input |
| EL | $475 | 0.5 mV | 30 Ω | 300 Ω or more | 56 to 62 dB | Moving-coil input |
| SH MK II | $850 | 2 mV | 130 Ω | 47 kΩ | 44 to 50 dB | Moving-magnet input |
| SL MK II | $850 | 0.4 mV | 8 Ω | 80 Ω or more | 58 to 64 dB | Moving-coil input |
| SL Mono MK II | $850 | 0.4 mV | 23 Ω | 230 Ω or more | 58 to 64 dB | Moving-coil input |
| MH | $1,200 | 2 mV | 130 Ω | 47 kΩ | 44 to 50 dB | Moving-magnet input |
| ML | $1,200 | 0.4 mV | 8 Ω | 100 Ω or more | 58 to 64 dB | Moving-coil input |
| Umami Blue | $2,500 | 0.4 mV | 8 Ω | 80 Ω or more | 58 to 64 dB | Moving-coil input |
| Umami Red | $3,950 | 0.4 mV | 6 Ω | 60 Ω or more | 58 to 64 dB | Moving-coil input |
| Umami Black | $11,500 | 0.3 mV | 5 Ω | 50 Ω or more | 60 to 66 dB | Moving-coil input |
Koetsu9 cartridges: output, load and the gain to look for
| Cartridge | Price | Output | Internal impedance | Maker's load | Gain to look for | Input |
|---|---|---|---|---|---|---|
| Rosewood Signature | $7,995 | 0.4 mV | 5 Ω | 75 to 500 Ω | 58 to 64 dB | Moving-coil input |
| Urushi Tsugaru | $8,695 | 0.4 mV | not published | 75 to 500 Ω | 58 to 64 dB | Moving-coil input |
| Urushi Wajima | $8,695 | 0.4 mV | not published | 75 to 500 Ω | 58 to 64 dB | Moving-coil input |
| Urushi Black | $8,695 | 0.4 mV | not published | 75 to 500 Ω | 58 to 64 dB | Moving-coil input |
| Urushi Vermillion | $9,495 | 0.2 mV | not published | 50 to 500 Ω | 64 to 70 dB | Moving-coil input, high gain |
| Rosewood Signature Platinum | $12,495 | 0.3 mV | not published | 75 to 500 Ω | 60 to 66 dB | Moving-coil input |
| Onyx Platinum | $15,495 | 0.3 mV | not published | 75 to 500 Ω | 60 to 66 dB | Moving-coil input |
| Tigereye Platinum | $16,995 | 0.3 mV | not published | 75 to 500 Ω | 60 to 66 dB | Moving-coil input |
| Blue Lace | $19,995 | 0.3 mV | not published | 75 to 500 Ω | 60 to 66 dB | Moving-coil input |
Luxman1 cartridge: output, load and the gain to look for
| Cartridge | Price | Output | Internal impedance | Maker's load | Gain to look for | Input |
|---|---|---|---|---|---|---|
| LMC-5 | $2,995 | 0.4 mV | 4.7 Ω | 40 Ω or more | 58 to 64 dB | Moving-coil input |
Lyra10 cartridges: output, load and the gain to look for
| Cartridge | Price | Output | Internal impedance | Maker's load | Gain to look for | Input |
|---|---|---|---|---|---|---|
| Delos | $2,495 | 0.6 mV | 8.2 Ω | 91 Ω or more | 54 to 60 dB | Moving-coil input |
| Kleos | $4,495 | 0.5 mV | 5.4 Ω | 95 to 816 Ω | 56 to 62 dB | Moving-coil input |
| Kleos SL | $4,995 | 0.25 mV | 2.7 Ω | 27 Ω or more (ten times its impedance) | 62 to 68 dB | Moving-coil input, high gain |
| Kleos Mono | $4,995 | 0.25 mV | 5.4 Ω | 95 to 816 Ω | 62 to 68 dB | Moving-coil input, high gain |
| Etna Lambda | $10,495 | 0.56 mV | 4.2 Ω | 104 to 887 Ω | 55 to 61 dB | Moving-coil input |
| Etna Lambda SL | $11,495 | 0.25 mV | 1.52 Ω | 15.2 Ω or more (ten times its impedance) | 62 to 68 dB | Moving-coil input, high gain |
| Etna Lambda Mono | $11,495 | 0.25 mV | 3 Ω | 30 Ω or more (ten times its impedance) | 62 to 68 dB | Moving-coil input, high gain |
| Atlas Lambda | $14,500 | 0.56 mV | 4.2 Ω | 104 to 887 Ω | 55 to 61 dB | Moving-coil input |
| Atlas Lambda Mono | $15,500 | 0.25 mV | 3 Ω | 104 to 887 Ω | 62 to 68 dB | Moving-coil input, high gain |
| Atlas Lambda SL | $15,500 | 0.25 mV | 1.52 Ω | 15.2 Ω or more (ten times its impedance) | 62 to 68 dB | Moving-coil input, high gain |
Ortofon11 cartridges: output, load and the gain to look for
| Cartridge | Price | Output | Internal impedance | Maker's load | Gain to look for | Input |
|---|---|---|---|---|---|---|
| OM 5E | $86 | 4 mV | 750 Ω | 47 kΩ | 38 to 44 dB | Moving-magnet input |
| 2M Red | $110 | 5.5 mV | 1.3 kΩ | 47 kΩ | 35 to 41 dB | Moving-magnet input |
| 2M Blue | $220 | 5.5 mV | 1.3 kΩ | 47 kΩ | 35 to 41 dB | Moving-magnet input |
| MC Quintet Red | $420 | 0.5 mV | 7 Ω | 20 Ω or more | 56 to 62 dB | Moving-coil input |
| 2M Bronze | $460 | 5 mV | 1.2 kΩ | 47 kΩ | 36 to 42 dB | Moving-magnet input |
| MC Quintet Blue | $600 | 0.5 mV | 7 Ω | 20 Ω or more | 56 to 62 dB | Moving-coil input |
| 2M Black | $750 | 5 mV | 1.2 kΩ | 47 kΩ | 36 to 42 dB | Moving-magnet input |
| MC Cadenza Red | $1,600 | 0.45 mV | 5 Ω | 50 to 500 Ω | 56 to 62 dB | Moving-coil input |
| MC Cadenza Blue | $2,140 | 0.5 mV | 5 Ω | 50 to 200 Ω | 56 to 62 dB | Moving-coil input |
| MC Cadenza Bronze | $2,600 | 0.4 mV | 5 Ω | 50 to 200 Ω | 58 to 64 dB | Moving-coil input |
| MC Cadenza Black | $3,200 | 0.33 mV | 5 Ω | 10 Ω or more | 59 to 65 dB | Moving-coil input |
Sumiko7 cartridges: output, load and the gain to look for
| Cartridge | Price | Output | Internal impedance | Maker's load | Gain to look for | Input |
|---|---|---|---|---|---|---|
| Rainier MM | $199 | 5 mV | 1.1 kΩ | 47 kΩ | 36 to 42 dB | Moving-magnet input |
| Olympia MM | $299 | 4 mV | 1.1 kΩ | 47 kΩ | 38 to 44 dB | Moving-magnet input |
| Moonstone MM | $399 | 3 mV | 1.1 kΩ | 47 kΩ | 40 to 46 dB | Moving-magnet input |
| Amethyst MM | $799 | 2.5 mV | 700 Ω | 47 kΩ | 42 to 48 dB | Moving-magnet input |
| Songbird High | $1,099 | 2.5 mV | 135 Ω | 47 kΩ | 42 to 48 dB | Moving-magnet input |
| Songbird Low | $1,099 | 0.5 mV | 28 Ω | 100 Ω or more | 56 to 62 dB | Moving-coil input |
| Starling | $2,099 | 0.5 mV | 28 Ω | 100 Ω or more | 56 to 62 dB | Moving-coil input |
Stage by stage
Each phono stage has a page of its own, with the cartridges in its price range and the sum for each.
To $2,500
$215 · Moving magnet only. 40 dB (5 mV in for 500 mV out). 47 kΩ with 100 pF. We pair it only with the Rega Carbon and the Nd3.
$445 · Moving magnet only. 41.4 dB. 47 kΩ with 100 pF. For the Rega Nd3, Nd5, Nd7 and Nd9.
$555 · Moving coil only. 63.5 or 69.5 dB. Loads of 70, 100, 150 or 400 Ω.
$600 · Moving magnet and moving coil. 40, 50, 54, 60 or 66 dB. Loads of 10, 100 or 475 Ω, or 47 kΩ.
$620 · Moving magnet and moving coil. 34 dB (MM) or 54 dB (MC). Selectable MC load.
$950 · Moving magnet and moving coil. 34 dB (MM) or 54 dB (MC). MC loads of 50, 100 or 500 Ω, 1 kΩ or 5 kΩ.
$2,000 · Moving magnet and moving coil. 46 dB (MM) or 66 dB (MC). MC load fixed at 500 Ω.
$2,300 · Moving magnet and moving coil. 40 dB (MM); 54, 60 or 66 dB (MC). Loads of 10, 100 or 470 Ω, 1 kΩ or 47 kΩ.
$2,395 · Moving coil only. 63.5 or 69.3 dB. Loads of 70, 100, 150 or 400 Ω.
$2,500 · One moving-magnet and one moving-coil input. 40 dB (MM) or 60 dB (MC). MC loads from 25 Ω to 1 kΩ. We use it with moving coils of 0.35 mV and above.
$3,000 to $5,000
$2,995 · Moving magnet and moving coil. 38 dB (MM); 57 dB on the MC high input (40 Ω) or 66 dB on the MC low input (2.5 Ω).
$3,699 · Moving magnet and moving coil. 42 dB (MM); 61 or 67 dB (MC). Sixteen MC loads from 85 Ω to 1 kΩ.
$3,740 · Moving magnet and moving coil, on RCA and XLR. 44 or 48 dB (MM); 54 or 64 dB (MC). Eleven MC loads from 31 Ω to 1 kΩ.
$4,290 · Moving coil only, fitted inside the Sondek LP12. 62.5 dB. Load fixed at 75 Ω.
$4,630 · Moving coil only, fitted inside the Sondek LP12, with a digital output. Gain and loading are set in Linn's software.
$4,800 · Moving magnet and moving coil, fully balanced. 46 dB (MM) or 66 dB (MC). MC load fixed at 500 Ω.
$4,950 · Moving magnet and moving coil. 50, 60 or 70 dB single-ended, 6 dB more balanced. Loads from 10 Ω to 47 kΩ.
$7,000 to $12,000
$7,995 · Moving magnet and moving coil, with a balanced input. 38 dB (MM); 57 or 66 dB (MC). MC loads from 4.7 Ω to 1 kΩ.
$8,500 · Moving magnet and moving coil, fully balanced. 40 to 70 dB in sixteen settings. Sixty-four loads from 12.1 Ω to 47 kΩ.
$12,000 · Vacuum tube. One input at 58 dB. Loads of 100, 200 or 500 Ω, 1 kΩ or 47 kΩ.
Reference
$13,283 · Moving magnet and moving coil, two chassis. 56, 66 or 76 dB. Loads from 30 Ω to 1 kΩ, or 47 kΩ.
$13,500 · Moving magnet and moving coil, fully balanced. 40 to 70 dB in sixteen settings. Sixty-four loads from 12.1 Ω to 47 kΩ.
$13,975 · Moving magnet and moving coil, fully balanced. 34 or 40 dB (MM); 64 or 70 dB (MC). MC loads from 10 Ω to 1 kΩ.
$22,000 · Plug-in MM and MC modules, balanced. 37 to 52 dB (MM) or 57 to 72 dB (MC), each in six steps. MC loads from 33 Ω to 1 kΩ.
$22,000 · Moving magnet and moving coil, fully balanced. 44 dB (MM) or 70 dB (MC). Loading is set on Personality Cards.
In a class of its own
$62,000 · Moving magnet and moving coil, fully balanced, with a separate power supply. 40 or 50 dB (MM); 60 or 70 dB (MC). Loading is set on Personality Cards.
Ask us
Tell us the cartridge you have, or the one you are considering, and the amplifier it plays into, and we will confirm the gain and load. Call (503) 222-2599 or email sales@pearlaudio.com.
Figures are the makers' own, as published on our product pages. The gold, silver and bronze bands are our rule of thumb. Sources for the pairings mentioned: The Absolute Sound, Stereophile and Boulder's literature.
