Turntables · Speed

How a turntable holds its speed

Every turntable has to turn at 33⅓ revolutions a minute and stay there. Makers go about it in different ways, and on most turntables the power supply is where the improvement is made.

Five ways to do it

  1. Follow the mains. A synchronous AC motor turns in step with the frequency of the electricity that feeds it. The McIntosh MTI100 works this way, as do the Rega Planar 1, 2 and 3 on their standard supply. The Majik LP12 filters the mains first.
  2. Make a better signal for the motor. An electronic supply generates its own signal from a crystal reference, so the motor no longer depends on the wall socket. Rega's Neo power supply does this.
  3. Regulate a DC motor. A DC motor runs from a steady voltage under electronic control. The Clearaudio Compass, the McIntosh MT5 and the Luxman PD-151 MKII are examples. Luxman's motor is brushless, under what it calls PID control.
  4. Measure the speed and correct it. A sensor reads the speed, and the electronics adjust the motor as the record plays. Linn's Lingo and Radikal, Clearaudio's Optical Speed Control turntables and the McIntosh MT10 read the platter with a light sensor. The Clearaudio Signature measures at the belt, without one. Optical speed control, maker by maker →
  5. Remove the belt. In a Technics direct-drive turntable the platter sits on the motor's rotor, and the motor's own electronics hold the speed. Technics and direct drive →

The Sondek LP12: basic, better, best

On an LP12 the speed is decided by the motor and its power supply. Linn makes three levels, and any of them can be fitted to any Sondek.

  • Basic: the Majik power supply. A compact supply inside the plinth. It filters the mains and runs the synchronous AC motor at a steady 33⅓ rpm. Singles are played with a pulley adaptor. It does not measure the platter.
  • Better: the Lingo. A control board inside the turntable and a slim supply outside it, with a new 12 V AC motor. An optical tachometer on the top plate reads a single marker on the inner rim of the outer platter, and the controller checks and corrects the speed on every rotation. It recalibrates each time the turntable is switched on, and 33⅓ and 45 are chosen at the switch.
  • Best: the Radikal. The AC motor gives way to a DC motor in an acoustic housing that keeps it apart from the deck. The same optical tachometer reads the platter, and the controller checks the speed on every rotation. The Radikal also powers a Urika phono stage inside the turntable. The Klimax Radikal is the reference version, with Linn's Utopik power supply.
A Sondek LP12 with part of the outer platter cut away, showing the tachometer on the top plate beside the motor pulley
A Sondek LP12 with part of the outer platter cut away. The small upright board beside the motor pulley is the tachometer. It faces the inner rim of the outer platter.

How the tachometer reads the platter →

Plan the next step for your LP12 →   Majik, Selekt and Klimax →

Rega: the Neo power supply

A Rega Planar 1, 2 or 3 runs its 24 V synchronous motor from a simple supply, and the speed is changed by moving the belt on the pulley.

The step up is the Neo power supply. It gives the motor a signal generated from a crystal reference, changes speed at the push of a button, and adjusts speed in steps of 0.01 rpm.

  • Planar 3. The Neo can be added at any time.
  • Planar 3 RS Edition, Planar 6, Planar 6 RS Edition and Planar 8. The Neo is included, matched to the motor by hand.
  • Planar 10 and Naia. Each has its own larger supply, on the same principle.
  • An older Rega. The 24 V Motor Upgrade Kit brings it to the current motor, which the Neo needs.

Rega turntables: the Planar range →   Build your Rega Planar →

Clearaudio: a cleaner supply for the motor

Clearaudio turntables use DC motors, and the control is built into the turntable. The upgrade is to the supply that feeds it.

  • Compass. A 12 V DC motor, with the speed chosen by a switch.
  • Signature. Tacho Speed Control measures the speed at the belt and calibrates at every start. It is a close relative of Optical Speed Control, but it is not optical. With the Satisfy tonearm the Signature comes with a plug-in supply. The Professional Power 12V, a transformer-based linear supply, is included with the other tonearms and can be added later.
  • Ovation, Innovation and above. A 24 V motor under Optical Speed Control, with an infrared sensor reading the platter. The Professional Power 24V is the supply made for these turntables, and the Smart Power 24V is the step beyond it.

Clearaudio turntables: from the Compass to the Statement →   Build your Clearaudio Signature →

Side by side

Where it startsThe first stepBeyond that
Linn Sondek LP12Majik power supply: filtered mains to an AC motorLingo: optical tachometer, speed checked on every rotationRadikal: DC motor with the optical tachometer; Klimax Radikal
Rega Planar24 V motor on a simple supply; belt moved by handNeo power supply: crystal reference, electronic speed changeThe Planar 10 and Naia supplies
Clearaudio12 V DC motor; plug-in supplyProfessional Power 12V linear supplyOptical Speed Control turntables; Professional Power 24V; Smart Power 24V

Optical speed control →   Turntable upgrade paths →

More on turntables

By maker

Search