Linn · Sondek LP12 · Phono stages
A tale of two Urikas
Linn makes two phono stages that fit inside the Sondek LP12. They share a name, a place in the turntable and a power supply. One is analog and one is digital, and they suit different systems.
The first Urika

The Urika arrived in April 2009, together with the Radikal power supply. It is a moving coil phono stage, and it lives inside the Sondek LP12.
No phono stage had been put there before, for a good reason. The LP12's motor until then ran on alternating current, and its electrical and magnetic fields were too close for a circuit handling so small a signal. The Radikal's motor runs on direct current and radiates very little. That made room for the phono stage.
How it is built
- It hangs with the turntable. The Urika sits in a light enclosure on its own suspended base board, so it is isolated from vibration in the same way the deck is.
- It is two phono stages. Each channel has its own circuit board, its own power regulation and its own ground return. Linn makes the two boards as a mirrored pair and keeps them together all the way through production.
- The equalization is direct-coupled. There are no capacitors in the direct path of the signal, and Linn's specification holds the response within 0.15 dB of the standard curve from 20 Hz to 20 kHz.
- Gain and load are fixed. 62.5 dB of gain, into a load of 75 ohms. There is nothing to set.
- It is powered by the Radikal and runs only while the turntable runs.
Reviewing its successor for hi-fi+, Alan Sircom described the first Urika's circuit as four steps: gain with the first part of the equalization, then the second part, then two stages of rumble filtering.
Its two outputs
- RCA, direct-coupled. Linn's choice for interconnects of ordinary length.
- XLR, balanced through a transformer. For a long cable run, or where the electrical ground in the building is poor. Linn uses the transformers it fitted to its Klimax DS player.
Either one feeds a line input on any preamplifier or integrated amplifier. The signal leaving the turntable is already at full level, so the cable to the system is no longer the delicate one.
Matched to Linn's cartridges
A phono stage with fixed gain and a fixed load only works if the cartridge suits it. Linn's do.
| Linn moving coil | Output | Load Linn recommends |
|---|---|---|
| Koil | 0.4 mV | 100 ohms |
| Kendo | 0.45 mV | 100 ohms |
| Krystal | 0.5 mV | 50 to 200 ohms |
| Ekstatik | 0.45 mV | 100 ohms |
All four produce between 0.4 and 0.5 mV, and all four want a load close to the 75 ohms the Urika gives them.
That narrow band is deliberate. Linn specifies its moving coils and its phono stage as a pair. Each moving coil it has introduced since 2009 has been designed to suit the Urika's input, so a new Linn cartridge can go onto a turntable with an existing Urika and nothing else needs to change.
Our own rule follows from it. We fit either Urika with a Linn moving coil, or with another maker's moving coil of 0.3 to 0.5 mV. Neither Urika takes a moving magnet cartridge.
Linn cartridges and the tonearms that suit them → The Urika II and the cartridges that suit it →
Ten inches of cable
The most fragile signal in a music system is the one in the tonearm cable. A moving coil cartridge produces less than a thousandth of a volt, and the phono stage multiplies it more than a thousand times. Anything else the cable picks up is multiplied with it.
With a phono stage on a shelf, Linn's arm cable was 1.7 meters long. With a Urika it is 0.25 meters, about ten inches. Linn also changed how it is made:
- It is balanced, so interference that lands on both conductors cancels.
- It is fully screened.
- It is soldered straight to the input of each channel, with no plugs on the way.
And it never leaves the turntable. It runs from the arm to the Urika with the stainless steel top plate above it and the Urika's base board, which Linn builds with a layer of steel, below it. The cartridge's signal is inside metal from the arm to the first stage of gain.
Why that matters in Portland
A long arm cable is an antenna. Most of Portland's FM and television stations transmit from the towers on the West Hills, close to where people live, and in some parts of the city a low-output moving coil and a conventional arm cable will pick up a station.
A short lead, balanced, screened and enclosed in metal, gives radio very little to get hold of. That is true of both Urikas, and it is one of the reasons we fit them here.
The Urika II
The Urika II followed in January 2018. It sits in the same place, takes its power from the same Radikal, and takes the place of the first Urika. What it does with the signal is different.
- It converts to digital inside the turntable. The first stage is still analog: gain, and the first part of the equalization. Then the signal is converted, a few inches from the cartridge.
- The rest of the equalization is done as arithmetic. A digital filter can follow the curve more exactly than resistors and capacitors, which vary a little from part to part.
- Each one is measured. Linn tests every Urika II at the factory and stores a correction for the small variations in its analog stage. It is the method Linn uses for its Exakt loudspeakers.
- The load is a setting. The cartridge is chosen from Linn's list, or its values are entered by hand. We set it when we fit the cartridge, and change it if you change cartridges.
- It keeps time with the rest of the system. The conversion runs from the clock in the Linn DSM, which reaches the turntable down the same cable.
The result is that the record's signal leaves the turntable as data. Distance stops mattering, and so does everything the cable passes on the way.
The Urika II's outputs
Move the pointer over the picture to magnify it. Select the picture to see it full size.
Two Exakt Link ports
These are the reason to choose a Urika II. Exakt Link is Linn's own digital connection. It carries the music, the clock and the signal that switches things on, all on one cable, with nothing lost on the way.
The ports take ordinary Ethernet cable, Cat 5 or Cat 6. They are not Ethernet ports, and the cable must not pass through a network switch or a router. It runs from the turntable to an Exakt Link port on the Linn DSM.
- The cable can be very long. Linn's guidance is up to 100 meters for the solid cable installed in walls.
- The DSM treats the turntable like any other source, with its volume control and its tuning for the room.
- In an Exakt system the signal stays digital all the way to the loudspeakers.
One optical output
Beside the Exakt Link ports is a Toslink optical output. Linn provides it for a digital recorder, and it carries the record at 24 bits and 192 kHz.
Its established use is copying records: an archive of a collection, or a transfer of a rare pressing made once and played from the copy. Two things are worth knowing:
- It works only while the Urika II is also connected to a Linn DSM by Exakt Link, because the clock and the switching arrive that way.
- Not every optical input accepts 192 kHz. The recorder's has to.
In practice few owners use it. Exakt Link is where the benefit of this phono stage lies.
There is no analog output on a Urika II. If the system has an analog preamplifier, the first Urika is the one to fit.
Why are there two ports on a Urika II?
It is a fair question. The two ports look like the Ethernet ports on a computer, and it is natural to wonder which one goes to the network.
Neither does. Both are Exakt Link ports, and there are two so that the Urika II can be one link in a chain.
- The primary port takes the cable from the Linn DSM. It is always used. The record's signal goes to the DSM through it, and the DSM's clock and control come back the same way.
- The secondary port passes Exakt Link on to the next Exakt product, such as an Exakt loudspeaker or an Exaktbox. In many systems it is left empty.
(Linn's documents use an older pair of names for the two. Primary and secondary are the terms in general use today.)
One thing to know before using the second port
The Urika II is powered by the Radikal, so it is on only while the turntable is on. Anything connected after it loses its link when the turntable is switched off.
Linn's own example is a DSM, then a Urika II, then an Exakt loudspeaker. Stop the turntable and the loudspeaker goes off with it.
For that reason we connect Exakt loudspeakers directly to the DSM's own ports and give the Urika II a cable to itself. Its second port stays empty.
Side by side
| Urika | Urika II | |
|---|---|---|
| Introduced | April 2009 | January 2018 |
| What leaves the turntable | An analog signal at full level | Data |
| Equalization | Analog | First part analog, the rest digital |
| Gain and load | Fixed: 62.5 dB, 75 ohms | Set in software for the cartridge |
| How each one is made consistent | Two boards built as a matched pair | Measured at the factory and corrected in software |
| Outputs | RCA and balanced XLR | Two Exakt Link ports, one optical |
| Connects to | Any preamplifier or integrated amplifier | A Linn DS or DSM with Exakt Link |
| Cable to the system | Interconnects; XLR for a long run | Ethernet cable, up to 100 meters |
| Cartridges | Moving coil | Moving coil |
| Power | Radikal | Radikal |
How they compare in use
Alan Sircom compared the two for hi-fi+ in a Linn system. He heard three things at once from the Urika II: greater accuracy, more detail, and almost no noise. What the first Urika did well was kept. "If you like the Urika, you'll want the Urika II," he wrote.
That comparison needs a Linn DS or DSM to make at all. Linn has kept the first Urika in its range, and in a system built around an analog preamplifier it is the only one of the two that can be used.
Which one
- A Linn DSM with Exakt Link: the Urika II. The record joins the system as data, and the turntable can go where you want it.
- Any other preamplifier or integrated amplifier: the Urika. It is analog from the stylus to the loudspeaker.
- A Urika now and a Linn DSM later: the Urika II fits in the same place, so the change is a workshop visit and not a new turntable.
Both need a Radikal, and both are for moving coil cartridges.
Urika
$4,290
Analog. RCA and XLR outputs, for any preamplifier.
Urika II
$4,630
Digital. Exakt Link ports, for a Linn DSM with Exakt Link.
Radikal
$6,270
The power supply and motor both Urikas need.
An LP12 that can sit a hundred feet from the system → Exakt: the signal stays digital to the loudspeaker → LP12 upgrades: plan the next step →
Sources
- Linn, Urika product information and "Radikal and Urika: key technology", April 2009
- Linn: Urika II
- LinnDocs: Urika II and Exakt Link
- hi-fi+: Linn Products Urika II phono stage, by Alan Sircom
