← Back to your LP12 build

Pass Labs · X Series

Pass Labs X150.8 Stereo Power Amplifier

$7,865

Signature technologiesThe Pass Labs story

Not currently in our rooms. For a serious buyer we will often bring a piece in from the manufacturer for a private session — tell us about your system and what you are weighing it against, and we will advise.

Pass Labs · X Series

The entry to the X series: 150 watts per channel of Class AB with a generous Class A bias, 40 output MOSFETs per channel and the same chassis as the XA30.8.

Shares its chassis and price with the Class A XA30.8; the X150.8 trades Class A envelope for five times the rated power.

150 W
per channel into 8 Ω
40
output MOSFETs per channel
150
damping factor
88 lb
weight (19 in wide)

Authorized Pass Labs dealer · Delivery and installation by Pearl Audio · Trade-ins welcome

The story

The X150.8 is the smallest of the Class AB .8 amplifiers. Pass says it operates higher into Class A than its predecessors, which in practice means the first watts, the ones most listening uses, are delivered in Class A before the output stage moves into AB on peaks. Forty power MOSFETs per channel are rated at 150 W into 8 Ω, with 26 dB of gain, a damping factor of 150 and a 100 kΩ balanced input. The chassis is the 7.5-inch-tall .8 enclosure with the blue meter, and the amplifier draws 370 W at idle.

Positive Feedback's Juan C. Ayllon found the X150.8 neutral with a slightly warm voicing, adding no sparkle and revealing the strengths and flaws of each recording, and used it as a reference amplifier. Pass describes its balance as speed and sweetness, punch and finesse. It is the X amplifier for a listener who wants more power than the XA30.8 for the same money and is prepared to give up some of the Class A envelope.

The XP-12 is the natural preamplifier, with the XP-22 a step up. The X250.8 adds 100 W and 16 more output devices per channel.

The X series began with the X1000 of 1998, the first amplifier built on Supersymmetry, the balanced circuit Nelson Pass patented in 1994 in which two matched halves cancel each other's distortion and noise at the output; the X150 followed, and Pass still calls the X series the mainstay of the company's amplifiers. The X150.8 is the smallest of the nine Point 8 amplifiers announced on January 7, 2014, and it is built in Auburn, California. Read the Pass Labs story →

Key technologies

  • Class AB with Class A bias. Runs higher into Class A than its predecessors before the output stage moves into AB.
  • 40 output MOSFETs per channel. Rated at 150 W into 8 Ω.
  • Balanced .8 front end. Constant-current sourcing, precise voltage references and current feedback.
  • Front-panel meter. Reads output-stage bias; rests near 10 o'clock on X amplifiers.
  • Balanced and single-ended inputs. XLR and RCA; 100 kΩ balanced, 50 kΩ single-ended.

The XA30.8 is the Class A amplifier in the same chassis; the XP-17 adds a phono stage to an XP-12 system.

Finishes

  • Silver anodized aluminum, standard
  • Black anodized aluminum, factory option

Silver is the standard finish shown. Black is available to order at additional cost; ask us for a quote.

Specifications
Type Stereo power amplifier
Class of operation Class AB, with Class A bias at low output
Power output (8 Ω) 150 W per channel
Power output (4 Ω) Not published by Pass Labs
Gain 26 dB
Input for full power (26 dB gain) 1.73 V
Frequency response 1.5 Hz – 100 kHz (Pass Labs spec)
Input impedance 50 kΩ single-ended; 100 kΩ balanced
Damping factor 150
Output devices 40 per channel
Inputs Balanced XLR and single-ended RCA
Outputs Speaker binding posts
Power consumption at idle 370 W
Standby power Less than 1 W
Dimensions (W × D × H) 19 × 21.25 × 7.5 in
Weight 88 lb
Sold as Single stereo amplifier

Pass Labs X150.8 product page and specifications

Where it sits in the range

The entry to the X series.

The matching preamplifier is the Pass Labs XP-12.

Reviews

Plan your Pass Labs system with Pearl Audio

Pearl Audio is an authorized Pass Labs dealer. Arrange an audition in our Portland showroom and we will help with loudspeaker matching, delivery and setup. Call (503) 222-2599 or email sales@pearlaudio.com.

Signature technologies

The engineering behind the Pass Labs X150.8 Stereo Power Amplifier

Pass Labs gives its technologies names because each one solves a specific problem. Here is what each does, where it came from, why it matters in a system, and what you may hear.

Two matched halves, cross-coupled so their errors cancelSince 1994

Supersymmetry

Supersymmetry, US patent 5,376,899, builds a balanced amplifier as two precisely matched halves and cross-couples them so that each half's distortion and noise appear identically on both outputs, where the balanced connection subtracts them while the music adds. It has been the basis of the X series since the X1000 of 1998. Read the deep diveClose

What it does

The patent, titled Amplifier with gain stages coupled for differential error correction, was issued in 1994, and Pass has described it to Stereophile as a circuit that cross-couples two balanced amplifiers so their noise and distortion match and cancel at the output. The point, in his own technical article, is not to reduce the distortion of each half: Su-Sy does not work by reducing the distortion per se. It is simply much easier to tweak the two halves of the circuit into symmetry than to make either half perfect, and once they are symmetrical their unwanted components cancel, which the article says can amount to as much as a 100:1 reduction. That lets a very simple circuit, with very little loop feedback, reach low distortion. The first product was the X1000 of 1998, followed by the X600, X350, X250 and X150; Desmond Harrington did the X1000's mechanical design. Pass calls the Super-Symmetric X series the mainstay of the company's amplifier products. The current X150.8, X250.8, X260.8, X350.8 and X600.8 are Supersymmetric Class AB amplifiers, and the same balanced front end feeds the XA .8 series and the INT-60 and INT-250 integrateds.

Why it matters in a system

Supersymmetry is how Pass Labs gets the low noise and low distortion of a balanced amplifier without the long feedback loops and extra gain stages that usually pay for them. For the owner it means the X amplifiers can be run balanced from source to loudspeaker, and that a 600-watt monoblock and a 30-watt Class A stereo amplifier share the same front end and the same family sound.

What you may hear

Dwayne Carter, reviewing the X260.8, wrote that the amplifiers "are as close to perfection as you can get" and that "It does everything very well, without drawing much attention to itself."

More power, fewer stages, lower distortion and less feedbackSince 2014

The Point 8 generation

Announced on January 7, 2014 after seven years of development, the .8 amplifiers kept the X and XA topologies and changed nearly everything around them: a DC-coupled current-feedback front end tailored to each output stage, deeper Class A bias, bigger heatsinks and a third more power-supply capacitance. Every current Pass Labs power amplifier except the XA25 belongs to it. Read the deep diveClose

What it does

The press release named nine amplifiers, the X150.8, X250.8, X350.8, X600.8, XA30.8, XA60.8, XA100.8, XA160.8 and XA200.8, seven years in the making, with more power, fewer stages, lower distortion and less feedback. The front ends are directly coupled, with 100 kHz open-loop bandwidth, and the input stage was changed from voltage feedback to current feedback; Stereophile described the XA200.8's front end as four each of complementary, discontinued Toshiba JFET, MOSFET and bipolar devices. The larger models are biased more deeply into the Class A region. Output-device counts are 40 on the XA30.8, XA60.8, X150.8 and X260.8, 56 on the X250.8 and XA100.8, and 72 on the X350.8, X600.8, XA160.8 and XA200.8, higher-power Toshiba MOSFETs run at a fraction of their ratings. The power supplies gained a third more storage capacitance and new CRC filtering, paralleled fast and soft rectifiers and large Plitron toroidal transformers, and output noise improved by more than 10 dB. The X260.8 monoblock joined the series later, with a spec sheet dated January 2022. The INT-60 and INT-250 of January 2015 are described by Pass Labs as descended from the series, and Pass has said the .8 amplifiers' weight is almost entirely chassis, heatsinks and power-supply transformer.

Why it matters in a system

The .8 series is why a Pass Labs amplifier bought today is larger and heavier than its .5 predecessor of the same rating: the XA60.8 weighs 22 pounds more than the XA60.5. Pass's explanation is that when all else is made equal, the amplifier with the bigger hardware seems to have the advantage, and the bigger supply and heatsinks are what let it hold its bias and its composure into difficult loudspeaker loads.

What you may hear

John Atkinson, measuring the XA200.8 for Stereophile, concluded that its performance "reveals some well-balanced audio engineering." Pete Davey of Positive Feedback wrote in September 2025 that the X350.8 "has reminded me why these big, heavy beasts are still so special."

The meter reads current, not wattsSince 2002

Class A to rated power, and the bias meter

A Pass Labs Class A amplifier is biased so its idle current keeps it in Class A up to its rated 8-ohm output; past that it moves smoothly into Class AB and keeps going, so an XA30.8 delivers about 94 watts before clipping. The round meter on the front panel shows output-stage current draw, and only moves when the amplifier leaves Class A. Read the deep diveClose

What it does

Pass's technical article Leaving Class A explains that the meters on Pass amplifiers are different: they reflect the current consumption of the amplifier rather than its output power. A push-pull stage operates in Class A up to the point where the output current is twice the bias current; beyond that one half shuts off and the amplifier is in Class AB, with no separate circuit switching in and no audible click at the transition. The XA ratings are the Class A envelope, not the limit. The Hi-Fi News lab report on the XA30.8 measured 94 watts into 8 ohms and 156 into 4, with the transition probably at about 45 watts; John Atkinson measured the XA60.8 at 150 watts into 8 ohms, the XA200.8 at 258, 480 and 700 watts into 8, 4 and 2 ohms, and the XA25 at 80 watts into 8 ohms. On the Class AB X-series amplifiers the same meter shows the smaller Class A region, which Positive Feedback put at the first 34 watts for the X260.8, and the X350.8 is biased deeply into Class A for the first handful of watts. The integrateds follow suit: Pass says the INT-60 runs in Class A to somewhat less than half its rated 60 watts, and the INT-250 to about 15 watts.

Why it matters in a system

The practical result is that a Pass Labs amplifier can be chosen by its Class A rating with the knowledge that two to three times that power is available for peaks, and the meter tells the owner how often the music asks for it. A needle that rarely moves means the loudspeaker is living inside the Class A region; one that swings constantly suggests a larger model or a more sensitive loudspeaker.

What you may hear

Mark Craven, Hi-Fi News, July 2025, on the XA30.8: the asking price "looks like a bargain," and the amplifier "puts nothing between you and the music." Pass Labs' own line is that the XA30.8 is proof that 30 watts can feel limitless.

Smoother bends on the transfer curveSince 1978

Low feedback and low-order harmonics

Pass accepts a little second- and third-harmonic distortion in exchange for avoiding the high-order products and extra gain stages that heavy negative feedback brings. His stated preference is for 2nd and 3rd harmonic components over 4th, 5th, 6th, 7th and so on, and his designs have used little or no loop feedback since the Stasis amplifiers of 1978. Read the deep diveClose

What it does

Pass's technical article Audio Distortion and Feedback sets out the position: negative loop feedback creates higher order distortion harmonics, and while negative feedback can reduce the total quantity of distortion, it adds new components of its own. To get lower order harmonic character, he writes, we want smoother bends on the device's transfer curve, rather than a curve forced straight by feedback. He has described his own evolution from a focus on the best measurable performance toward Bart Locanthi's philosophy of making circuits as linear as possible and then applying modest feedback, which led by 1978 to the Stasis amplifiers without global feedback, built on his 1978 patent for a current bootstrap that holds output current nearly constant. At Pass Labs the same rule governs the Aleph, the Supersymmetric X series, where feedback around the front end sets the gain and the output stages are left alone, and the XA25, which has no negative feedback in its stages. Pass told Stereophile that negative-phase second harmonic tends to expand the perception of front-to-back space in the soundstage. John Atkinson's measurement of the INT-25 found its distortion at 10 watts dominated by a second harmonic at about -86 dB, which he called subjectively benign, with higher-order harmonics virtually absent.

Why it matters in a system

This is the design decision behind the Pass Labs sound: the amplifiers are not the lowest-distortion devices on a test bench, but what distortion remains is of the low-order kind that the ear tolerates and may even read as space. It also explains the simplicity of the circuits, since every gain stage removed is one less place for high-order products to arise, and the amplifiers' stability into awkward loads.

What you may hear

Pass put it plainly to Stereophile: "I don't think the audiophile wants technical perfection. He wants to be happy." Neil Gader, The Absolute Sound, on the XP-17: "Neither explicitly solid-state nor tube in character, it dishes out savory tastes of both."

MOSFETs love currentSince 1992

MOSFET output stages

Pass Labs uses power MOSFETs rather than bipolar transistors because their transfer curve resembles a triode's and suits high-bias Class A operation. The .8 amplifiers run banks of 40 to 72 Toshiba MOSFETs per chassis far below their ratings; the Xs 300 uses 112 per channel. Read the deep diveClose

What it does

Stereophile's 1997 review of the Aleph 1.2 noted that power MOSFETs serve as both gain stages because their transfer curve suits single-ended class-A operation, and Pass's summary to the same magazine was three words: MOSFETs love current. In the .8 generation the output devices are higher-power Toshiba MOSFETs operated at a fraction of their ratings, 40 per chassis on the XA30.8, XA60.8, X150.8 and X260.8, 56 on the XA100.8 and X250.8, and 72 on the XA160.8, XA200.8, X350.8 and X600.8; Hi-Fi News counted ten pairs of 20-amp FETs per channel in the XA30.8's current-feedback output stage. The INT-250 carries 20 per channel rated at 150 watts each, and the Xs 300 112 per channel. Running many devices well inside their limits is what allows the deep Class A bias, the low output impedance and the longevity; it is also the reason the XA200.8 weighs 157 pounds, most of it, in Pass's words, chassis, heatsinks and power-supply transformer. The XA25 goes the other way, with a single pair of 700-watt FETs per channel, and the HPA-1c headphone amplifier uses a direct-coupled MOSFET output stage with no ICs in the signal path. Pass's First Watt company has explored static induction transistors, which he says behave like a triode tube.

Why it matters in a system

Device choice sets how an amplifier behaves at the edges: into low impedances, at clipping, and after years of heat. A large bank of MOSFETs run gently gives a Pass Labs amplifier the current reserves that let an XA60.8 deliver 150 watts into 8 ohms at clipping and an XA200.8 700 watts into 2 ohms, and gives the owner an amplifier that does not need to be babied.

What you may hear

Jason Victor Serinus, Stereophile, on the XA200.8: "It is the most beautiful-sounding, color-rich amplifier ever to grace my system." John Atkinson's bench summary of the XA25: it "performed well on the test bench, as I've come to expect from Pass Labs."

Hand-assembled boards, three days in a constant-temperature roomSince 2014

Built, burned in and biased in Auburn, California

Every Pass Labs product is built in the company's factory in Auburn, California, which it moved into on April 15, 2014. Circuit boards are hand-assembled and inspected, front panels are machined from a single aluminum slab and hand-anodized to match each chassis, and every finished amplifier runs for three days in a room held at constant temperature so that its bias can be set identically to every other. Read the deep diveClose

What it does

Pass Laboratories began in 1991 in Nelson Pass's home shop, where he and Mike Burley built an in-house machine shop with three home-built CNC milling machines. The company moved to Foresthill, California by 1997, and on April 15, 2014 into a new factory in Auburn almost three times the size of the former space, with all operations under one roof; its address is now 13395 New Airport Road in Auburn. The Audio Beatnik's 2017 factory tour, led by Desmond Harrington and Kent English, described the process: circuit boards hand-assembled and inspected by technicians, front panels machined locally in Northern California from a single aluminum slab and hand-finished and hand-anodized to match their chassis, and finished amplifiers moved into a room kept at constant temperature year-round for burn-in and biasing, each running for three days so every unit's bias is identical. Harrington's description of the company's priorities was that it does not chase measured figures or build test equipment; it goes by sound. He also said there has never been a Pass Labs product made that the company does not have parts for. Amplifiers are built to order; Music Direct lists an eight-to-ten-week wait for an XA25.

Why it matters in a system

A Class A amplifier's bias is its sound, and setting it in a controlled room after three days of heat is why two XA60.8s built months apart behave as a pair. The parts policy matters more over time: a Pass Labs amplifier from the 1990s can still be serviced by the factory that built it, and the people who designed the current range still work there.

What you may hear

Consistency between the review sample and the one that arrives at home. Herb Reichert, writing in Stereophile about the INT-60, described "some of the best reproductions of music I've experienced this century."

All Pass Labs technologies and the company story

The Pass Labs story

Single-ended and Supersymmetric Class A amplification by Nelson Pass, built by hand in California since 1991.

Founded 1991 in Northern California; built in Auburn, California since 2014 by Nelson Pass · passlabs.com

Milestones

  1. 1974 Threshold After a physics degree at UC Davis and evenings assisting Oskar Heil at ESS, Nelson Pass co-founds Threshold Electronics in Sacramento in December. The 800A follows in 1975.
  2. 1978 Stasis, and the first designs for home builders The patented Stasis circuit lets an amplifier run without loop feedback; Nakamichi later licenses it. The same year he begins publishing simple Class A amplifiers for people to build at home.
  3. 1991 Pass Laboratories founded Nelson Pass leaves Threshold to build simpler amplifiers and starts the company in his home shop, building his own milling machines to make the casework.
  4. 1992 Aleph 0 The first product ships: a single-ended Class A monoblock built around power MOSFETs. Stereophile later names it Amplification Component of 1995.
  5. 1994 Supersymmetry patented; Wayne Colburn joins Supersymmetry pairs two balanced amplifier halves so their errors cancel. The Aleph is simplified to two gain stages, giving the Aleph 1.2, Aleph 2, Aleph 3 and Aleph P, and Wayne Colburn begins the preamplifier and phono work he leads to this day.
  6. 1997 Foresthill The company moves from the home shop into a facility in Foresthill, California. A revised Aleph P and the X0, X1 and Xono preamplifiers follow by 1999.
  7. 1998 X1000 The first Supersymmetric amplifier, followed by the rest of the X series. Around this time Nelson Pass also begins First Watt, his kitchen-table outlet for amplifiers of 25 watts or less.Pass Labs X250.8 Amplifier
  8. 2002 The XA series The XA200 and XA160 join the Supersymmetric circuit to an Aleph-style output stage.Pass Labs XA-60.8 Monoblock Amplifiers (pair)
  9. 2008 XA.5 and the XP preamplifiers Five XA.5 Class A amplifiers are announced, and the XP-10 and XP-20 begin the XP line of preamplifiers; the XP-15 phono stage follows in 2009.Pass Labs XP-12 Preamplifier
  10. 2012 Xs 150 and Xs 300 Two-chassis flagship monoblocks, after three years of development led by listening. The Xs Preamp follows in 2013.
  11. 2014 Point 8, and the Auburn factory Nine .8 amplifiers are announced in January after seven years of development, and in April the company moves into a factory in Auburn, California, nearly three times the size of Foresthill.Pass Labs XA-30.8 Stereo Amplifier
  12. 2015 INT-60 and INT-250 Integrated amplifiers descended from the Point 8 series. The HPA-1 headphone amplifier follows in 2016.Pass Labs INT-60 Integrated Amplifier
  13. 2017 XA25, XP-12 and XP-17 The XA25 is a 25-watt Class A amplifier with a single pair of output devices per channel. Wayne Colburn's XP-12 line stage and XP-17 phono stage arrive the same year.Pass Labs XA-25 Amplifier
  14. 2018 XP-22 and XP-27 A two-chassis line stage and phono stage. Stereophile names the XP-22 its Amplification Product of the Year for 2019; the INT-25 integrated follows in 2019.Pass Labs XP-22 Preamplifier
  15. 2021 XP-32 The three-chassis line stage replaces the XP-30, with one chassis per channel and a third for control and power.Pass Labs XP-32 Reference Line Preamplifier
  16. 2025 Xs Pre 2 and HPA-1c Wayne Colburn's three-chassis Xs Pre 2, which he has called his best work, and the HPA-1c, his revision of the HPA-1 headphone amplifier.Pass Labs HPA-1c Headphone Amplifier
Read the Pass Labs story
Pass Labs INT-60 and 160.8 monoblocks in the Small Room

Nelson Pass

Nelson Pass grew up with his mother's record collection and an AM radio. As a teenager he helped assemble a Heathkit, then put together his first system from a Garrard turntable, a Radio Shack amplifier and loudspeaker boxes he made himself, and soon had the amplifier apart to improve its cooling. By his second year of college he was building his own equipment. He studied physics at the University of California, Davis, taking his degree in 1974, and worked nights at the loudspeaker maker ESS, where he assisted Dr. Oskar Heil with crossovers, woofers and cabinets. A colleague there handed him a set of semiconductor application books, and from those he taught himself circuit design.

Threshold

In December 1974, with a partner from ESS, he founded Threshold Electronics in Sacramento. Money was short in the early years, but the first amplifier, the 800A of 1975, made the company's name: it used a new biasing scheme to deliver Class A performance at 200 watts. In 1978 came Stasis, a patented circuit that let an amplifier run without the corrective feedback other designs relied on. It carried Threshold through the 1980s and was licensed by Nakamichi.

Two habits from those years never left him. The first was a change of mind about measurement: having begun by chasing the best figures, he came to prefer circuits that are linear to start with and need little correction. The second was generosity. From 1978 he published simple Class A amplifiers for people to build at home, and he has gone on sharing designs with home builders ever since. In the mid-1980s he also designed the well-reviewed Adcom GFA-555.

How Pass Labs came to be

By 1991 he wanted to build something simpler. He left Threshold and started Pass Laboratories in his home shop in northern California. He and a colleague built their own milling machines to make the casework, and his next-door neighbor was hired to help build the amplifiers; she still helps run the company. The first product, the Aleph 0 monoblock, shipped in 1992: a single-ended Class A amplifier built around power MOSFETs, which he valued for behaving much as tubes do. Stereophile named it Amplification Component of 1995, and its reviewer called it “the solid-state amplifier of the decade.”

The Aleph

The idea behind the Aleph was that everything done to a musical signal leaves its mark, so the best circuit is the one that does the least. The second generation of 1994 had just two stages of amplification where conventional designs used as many as eight, needed no adjustment, and ran single-ended all the time, helped by a current source of his own invention. It asked listeners to think differently about power: a 200-watt amplifier sounds only about twice as loud as a 30-watt one, and the Aleph 3 offered 30 watts of a quality that made the trade worthwhile.

The Alephs looked like nothing else: black boxes with heatsink fins on every side and, on the larger models, a single blue light. They ran warm, and they were built to last, with input transistors chosen so strictly that only about one in ten passed. The family ran from the Aleph 3 through the Aleph 2 and the 200-watt Aleph 1.2 monoblocks to the Aleph P preamplifier. Reviewers of the day heard no electronic signature: ease, natural timbre, a three-dimensional soundstage, tuneful bass and a sweet top end.

Supersymmetry and the X amplifiers

In 1994 Nelson Pass patented Supersymmetry, which pairs the two balanced halves of an amplifier so that their noise and distortion match and cancel at the output. It let the company build much larger amplifiers on the same simple principles. The X1000 of 1998 was the first amplifier built on it, and the X series that followed remains the mainstay of the company's power amplifiers. The XA series of 2002 joined that circuit to an Aleph-style output stage; he has described the aim as a warm, sweet X amplifier or, put the other way, a powerfully dynamic Aleph.

The amplifiers of today

The two-chassis Xs monoblocks of 2012 were developed over three years, led by listening, and what was learned from them went into the Point 8 generation of 2014: nine X and XA amplifiers, seven years in the making, with deeper Class A operation, larger heatsinks and bigger power supplies. Integrated amplifiers descended from them followed in 2015, and in 2017 the XA25, a 25-watt Class A amplifier with a single pair of output devices in each channel. These are heavy machines. The XA60.8 puts 60 watts in a chassis of 88 pounds, and Nelson Pass has said that the weight is in the heatsinks and power transformers and that, all else being equal, the amplifier with the bigger hardware seems to have the advantage.

The words reviewers use for the current amplifiers are touch, texture, delicacy and sweetness, with body, impact, authority and a huge, precise soundstage, and no hardness. Stereophile's measurements of the XA60.8 found it quiet, with far more usable power than its 60-watt rating suggests.

First Watt

Alongside Pass Labs, Nelson Pass runs First Watt, which he describes as a kitchen-table venture, where he builds small numbers of amplifiers of 25 watts or less to try ideas that fall outside the main range. What he learns there comes back. Work with unusual transistors at First Watt taught him how the character of an amplifier's distortion shapes the sense of depth in a recording, and that understanding went into the Pass Labs amplifiers.

Wayne Colburn

Wayne Colburn joined in 1994 to work on an improved preamplifier and a new phono stage, and he has designed the company's preamplifiers and phono stages ever since: the later Aleph P, the Xono, the XP line that began in 2008, and the Xs preamplifiers at the top of the range. Stereophile named his XP-22 its Amplification Product of the Year for 2019, the three-chassis XP-32 followed in 2021, and the Xs Pre 2 of 2025 is one he has called his best work. At Pearl Audio we think especially highly of his phono stages.

Built in California

Pass Labs moved from the home shop to Foresthill, California, in 1997, and in 2014 to a factory in Auburn nearly three times the size, with every operation under one roof; research stays in the original shop. Circuit boards are assembled and inspected by hand, front panels are machined nearby from solid aluminum, and every amplifier runs for three days at a constant temperature before its bias is set.

Kent English is one of the two people who manage the day-to-day running of the company, and Nelson Pass and Wayne Colburn still design the products. Pass Labs keeps parts for everything it has made, which matters for an amplifier bought to be kept.

The complete Pass Labs story and technology library

Pass Labs at Pearl Audio

Before he was a dealer, John Loranger listened at home to a pair of Pass Aleph 2 monoblocks with the Aleph P preamplifier and the Xono phono stage, and he has known Nelson Pass and Wayne Colburn for more than twenty years. Pearl Audio first carried Pass Labs around 2005 and, after some years apart, carries it again today. We carry the XA and X .8 amplifiers, the XA25, the INT-60 and INT-250 integrateds, the XP line stages and phono stages and the HPA-1c, and we can order any current Pass Labs product in silver or black. Because a Class A amplifier's rating is its Class A envelope rather than its limit, we help match the model to the loudspeaker and the room, and we deliver, place and connect the heavier pieces ourselves. Pass Labs builds to order in Auburn, California, and the factory keeps parts for every product it has made.

The Pearl Audio experience

How we work with you

A system at this level should be heard, thoughtfully matched, and properly set up. From the first audition to long-term ownership, you work with the same people, in person.

  1. 01

    Listen first

    The Pass Labs X150.8 Stereo Power Amplifier is not in our rooms at present. When it is the right piece for a client we arrange a demonstration unit from the manufacturer and set it up for a private session.

  2. 02

    Delivery and installation

    We deliver and install throughout the Portland area, taking care of placement, connections, ventilation and system configuration ourselves.

  3. 03

    Support for as long as you own it

    We support everything we sell for as long as you own it, whether the answer comes by phone, in your home, or through factory service.

  4. 04

    A path for what comes next

    Trade-in assistance and qualifying 100% Trade-Up options give you flexibility when your listening priorities or your system change.

Search