← Back to your LP12 build

Pass Labs · XP Series

Pass Labs XP-27 Phono Preamplifier

$13,283

Signature technologiesThe Pass Labs story

Not currently in our rooms. For a serious buyer we will often bring a piece in from the manufacturer for a private session — tell us about your system and what you are weighing it against, and we will advise.

Pass Labs · XP Series

The two-chassis Pass Labs phono preamplifier: two inputs, three gain settings and loading on the front panel, with the power supply in its own box.

Two chassis: phono unit plus separate power supply. Two phono inputs. Reviewed in Stereophile, August 2024.

76 dB
maximum gain (56 / 66 / 76 dB)
2
phono inputs
-85 dB
unweighted noise ref. 1 mV (MC)
45 lb
total, two 17-inch chassis

Authorized Pass Labs dealer · Delivery and installation by Pearl Audio · Trade-ins welcome

The story

The XP-27 succeeds the XP-25 and takes the same approach: the power supply lives in a second chassis, linked by a shielded nine-conductor umbilical that carries power only, so transformer noise stays away from the low-level circuitry. The input and gain circuits are similar to those of the Xs Phono, with active gain stages rather than step-up transformers and three settings of 56, 66 or 76 dB. Each channel is loaded independently from the front panel: resistive loading from 30 Ω to 1 kΩ in eight steps for moving coils plus 47 kΩ for moving magnets, and capacitance from 100 to 750 pF in six steps. Input selection, gain, a low-cut filter and mute are also on the front panel.

Pass specifies RIAA accuracy within ±0.1 dB, distortion below 0.005% at 1 mV MC input, unweighted noise of -85 dB referenced to 1 mV (MC) and -93 dB referenced to 10 mV (MM), and a 22 V maximum output from a 150 Ω source. Stereophile's Jim Austin reported designer Wayne Colburn's account of the changes from the XP-25: lower-noise resistors, upgraded capacitors, a revised power supply and a gain control that no longer affects the RIAA equalization, improvements that fall below the analyzer's measurement range but are audible as lower noise and better bass. Part-Time Audiophile called the XP-27 the most authoritative phono stage in its test and gave it a Reviewer's Choice.

Two inputs make the XP-27 the choice for a two-arm turntable or two decks, and front-panel loading makes dialing in a new cartridge a matter of minutes from the listening chair. The chassis should not be stacked, so plan two shelves. The XP-22 or XP-32 are its line-stage partners; the single-input XP-17 is the one-box alternative.

Wayne Colburn has designed Pass Labs' phono stages since the Aleph Ono of 1997, through the Xono, the XP-15 of 2009, the XP-25 and the two-chassis Xs Phono of 2014 that the XP-27's input and gain circuits follow. The XP-27 was introduced with the XP-22 at AXPONA in April 2018 and is built in the company's factory in Auburn, California. Read the Pass Labs story →

Key technologies

  • Separate power supply. A second chassis linked by a shielded nine-conductor umbilical that carries power only.
  • Xs Phono circuitry. Input and gain circuits similar to the Xs Phono, with active gain rather than step-up transformers.
  • Front-panel loading. Independent resistive (30 Ω – 1 kΩ in eight steps, plus 47 kΩ) and capacitive (100 – 750 pF) loading per channel.
  • Two inputs. Front-panel selection between two turntables or tonearms, with gain, low-cut filter and mute.
  • Lower-noise parts than the XP-25. Lower-noise resistors, upgraded capacitors and a revised supply; gain setting no longer affects the RIAA curve.

A two-chassis phono stage belongs in a system built around the XA200.8 or XA160.8 monos.

Finishes

  • Silver anodized aluminum, standard
  • Black anodized aluminum, factory option

Silver is the standard finish shown. Black is available to order at additional cost; ask us for a quote.

Specifications
Type Solid-state MM/MC phono preamplifier, two chassis (separate power supply)
Inputs 2 pairs RCA
Outputs Balanced XLR and single-ended RCA
Gain 56 / 66 / 76 dB, selectable
Resistive loading 30, 50, 100, 160, 250, 320, 500 Ω, 1 kΩ and 47 kΩ, front panel
Capacitive loading 100, 200, 320, 430, 530 and 750 pF, front panel
RIAA accuracy ±0.1 dB, 20 Hz – 20 kHz
Distortion Less than 0.005% at 1 mV MC input; less than 0.002% at 10 mV MM input
Noise (unweighted) -85 dB ref. 1 mV (MC); -93 dB ref. 10 mV (MM)
Maximum output / output impedance 22 V rms / 150 Ω
Features Low-cut filter, mute, input select, all on the front panel
Power consumption 50 W
Dimensions (W × D × H) 17 × 12 × 4 in, each of two chassis
Weight 45 lb total

Pass Labs XP-27 product page and specifications

Where it sits in the range

The two-chassis Pass Labs phono preamplifier below the Xs Phono.

  • Pass Labs XP-17: single-chassis phono preamplifier, one input
  • Pass Labs XP-27 (this model)

The matching line preamplifiers are the XP-22 and XP-32.

Reviews

Plan your Pass Labs system with Pearl Audio

Pearl Audio is an authorized Pass Labs dealer. Bring your cartridge and tonearm details and we will set the gain and loading; arrange an audition in our Portland showroom. Call (503) 222-2599 or email sales@pearlaudio.com.

Signature technologies

The engineering behind the Pass Labs XP-27 Phono Preamplifier

Pass Labs gives its technologies names because each one solves a specific problem. Here is what each does, where it came from, why it matters in a system, and what you may hear.

Smoother bends on the transfer curveSince 1978

Low feedback and low-order harmonics

Pass accepts a little second- and third-harmonic distortion in exchange for avoiding the high-order products and extra gain stages that heavy negative feedback brings. His stated preference is for 2nd and 3rd harmonic components over 4th, 5th, 6th, 7th and so on, and his designs have used little or no loop feedback since the Stasis amplifiers of 1978. Read the deep diveClose

What it does

Pass's technical article Audio Distortion and Feedback sets out the position: negative loop feedback creates higher order distortion harmonics, and while negative feedback can reduce the total quantity of distortion, it adds new components of its own. To get lower order harmonic character, he writes, we want smoother bends on the device's transfer curve, rather than a curve forced straight by feedback. He has described his own evolution from a focus on the best measurable performance toward Bart Locanthi's philosophy of making circuits as linear as possible and then applying modest feedback, which led by 1978 to the Stasis amplifiers without global feedback, built on his 1978 patent for a current bootstrap that holds output current nearly constant. At Pass Labs the same rule governs the Aleph, the Supersymmetric X series, where feedback around the front end sets the gain and the output stages are left alone, and the XA25, which has no negative feedback in its stages. Pass told Stereophile that negative-phase second harmonic tends to expand the perception of front-to-back space in the soundstage. John Atkinson's measurement of the INT-25 found its distortion at 10 watts dominated by a second harmonic at about -86 dB, which he called subjectively benign, with higher-order harmonics virtually absent.

Why it matters in a system

This is the design decision behind the Pass Labs sound: the amplifiers are not the lowest-distortion devices on a test bench, but what distortion remains is of the low-order kind that the ear tolerates and may even read as space. It also explains the simplicity of the circuits, since every gain stage removed is one less place for high-order products to arise, and the amplifiers' stability into awkward loads.

What you may hear

Pass put it plainly to Stereophile: "I don't think the audiophile wants technical perfection. He wants to be happy." Neil Gader, The Absolute Sound, on the XP-17: "Neither explicitly solid-state nor tube in character, it dishes out savory tastes of both."

Designed by Wayne Colburn since 1994Since 2008

The XP preamplifiers and phono stages

Pass Labs' line stages and phono stages are designed by Wayne Colburn, who joined the company in 1994. The current XP generation borrows the single-stage attenuator, high-bias Toshiba-FET gain stages and auto-biased output stages of the Xs flagships, with separate double-shielded toroidal supplies in the two- and three-chassis models. Read the deep diveClose

What it does

Colburn joined Pass Labs in 1994 to work on an improved preamplifier and a new phono stage, and The Absolute Sound states it simply: Wayne Colburn designs Pass preamps. The XP-10 and XP-20 of October 2008 began the line; the two-chassis Xs Preamp of 2013 and the Xs Phono of 2014 became the references from which the current models descend. The XP-12 of May 2017 is the single-chassis line stage, with the single-stage volume control borrowed from the Xs line preamp in 100 steps of 1 dB and a double-shielded toroidal supply. The XP-22 of April 2018 adds an outboard dual-mono supply and an output stage that is larger and higher-biased, like the Xs Preamp's, with auto bias; Colburn's reasoning is that noise is the most prominent part of THD+N at low levels, so lowering noise buys resolution and dynamics. The XP-32 of 2020–21 puts each channel's audio circuitry in its own chassis, with DC coupling, higher Class A bias and 0.5 dB steps. The XP-17 phono stage of 2017 takes the Xs Phono's gain structure and RIAA network with DIP-switch loading, and the two-chassis XP-27 of 2018 its input and gain circuitry with front-panel rotary loading. The Xs Pre 2 of 2025 is Colburn's three-box flagship, and he also revised the HPA-1 headphone amplifier into the HPA-1c.

Why it matters in a system

A preamplifier sets the noise floor and the gain structure of everything downstream, and the XP models are built to be matched to Pass Labs amplifiers: balanced throughout, with about 9.3 dB of gain and output impedances low enough to drive long runs. The choice among XP-12, XP-22 and XP-32 is a choice of how much power supply and chassis separation the system will reward; the sound is the same family.

What you may hear

Jim Austin, Stereophile, June 2022: "It took me no more than five minutes to decide to keep the XP-32," which "gets out of the way, yet it somehow makes the music sound better." On the XP-27 he wrote that it "is liquid and detailed—and of course very quiet."

Hand-assembled boards, three days in a constant-temperature roomSince 2014

Built, burned in and biased in Auburn, California

Every Pass Labs product is built in the company's factory in Auburn, California, which it moved into on April 15, 2014. Circuit boards are hand-assembled and inspected, front panels are machined from a single aluminum slab and hand-anodized to match each chassis, and every finished amplifier runs for three days in a room held at constant temperature so that its bias can be set identically to every other. Read the deep diveClose

What it does

Pass Laboratories began in 1991 in Nelson Pass's home shop, where he and Mike Burley built an in-house machine shop with three home-built CNC milling machines. The company moved to Foresthill, California by 1997, and on April 15, 2014 into a new factory in Auburn almost three times the size of the former space, with all operations under one roof; its address is now 13395 New Airport Road in Auburn. The Audio Beatnik's 2017 factory tour, led by Desmond Harrington and Kent English, described the process: circuit boards hand-assembled and inspected by technicians, front panels machined locally in Northern California from a single aluminum slab and hand-finished and hand-anodized to match their chassis, and finished amplifiers moved into a room kept at constant temperature year-round for burn-in and biasing, each running for three days so every unit's bias is identical. Harrington's description of the company's priorities was that it does not chase measured figures or build test equipment; it goes by sound. He also said there has never been a Pass Labs product made that the company does not have parts for. Amplifiers are built to order; Music Direct lists an eight-to-ten-week wait for an XA25.

Why it matters in a system

A Class A amplifier's bias is its sound, and setting it in a controlled room after three days of heat is why two XA60.8s built months apart behave as a pair. The parts policy matters more over time: a Pass Labs amplifier from the 1990s can still be serviced by the factory that built it, and the people who designed the current range still work there.

What you may hear

Consistency between the review sample and the one that arrives at home. Herb Reichert, writing in Stereophile about the INT-60, described "some of the best reproductions of music I've experienced this century."

All Pass Labs technologies and the company story

The Pass Labs story

Single-ended and Supersymmetric Class A amplification by Nelson Pass, built by hand in California since 1991.

Founded 1991 in Northern California; built in Auburn, California since 2014 by Nelson Pass · passlabs.com

Milestones

  1. 1974 Threshold After a physics degree at UC Davis and evenings assisting Oskar Heil at ESS, Nelson Pass co-founds Threshold Electronics in Sacramento in December. The 800A follows in 1975.
  2. 1978 Stasis, and the first designs for home builders The patented Stasis circuit lets an amplifier run without loop feedback; Nakamichi later licenses it. The same year he begins publishing simple Class A amplifiers for people to build at home.
  3. 1991 Pass Laboratories founded Nelson Pass leaves Threshold to build simpler amplifiers and starts the company in his home shop, building his own milling machines to make the casework.
  4. 1992 Aleph 0 The first product ships: a single-ended Class A monoblock built around power MOSFETs. Stereophile later names it Amplification Component of 1995.
  5. 1994 Supersymmetry patented; Wayne Colburn joins Supersymmetry pairs two balanced amplifier halves so their errors cancel. The Aleph is simplified to two gain stages, giving the Aleph 1.2, Aleph 2, Aleph 3 and Aleph P, and Wayne Colburn begins the preamplifier and phono work he leads to this day.
  6. 1997 Foresthill The company moves from the home shop into a facility in Foresthill, California. A revised Aleph P and the X0, X1 and Xono preamplifiers follow by 1999.
  7. 1998 X1000 The first Supersymmetric amplifier, followed by the rest of the X series. Around this time Nelson Pass also begins First Watt, his kitchen-table outlet for amplifiers of 25 watts or less.Pass Labs X250.8 Amplifier
  8. 2002 The XA series The XA200 and XA160 join the Supersymmetric circuit to an Aleph-style output stage.Pass Labs XA-60.8 Monoblock Amplifiers (pair)
  9. 2008 XA.5 and the XP preamplifiers Five XA.5 Class A amplifiers are announced, and the XP-10 and XP-20 begin the XP line of preamplifiers; the XP-15 phono stage follows in 2009.Pass Labs XP-12 Preamplifier
  10. 2012 Xs 150 and Xs 300 Two-chassis flagship monoblocks, after three years of development led by listening. The Xs Preamp follows in 2013.
  11. 2014 Point 8, and the Auburn factory Nine .8 amplifiers are announced in January after seven years of development, and in April the company moves into a factory in Auburn, California, nearly three times the size of Foresthill.Pass Labs XA-30.8 Stereo Amplifier
  12. 2015 INT-60 and INT-250 Integrated amplifiers descended from the Point 8 series. The HPA-1 headphone amplifier follows in 2016.Pass Labs INT-60 Integrated Amplifier
  13. 2017 XA25, XP-12 and XP-17 The XA25 is a 25-watt Class A amplifier with a single pair of output devices per channel. Wayne Colburn's XP-12 line stage and XP-17 phono stage arrive the same year.Pass Labs XA-25 Amplifier
  14. 2018 XP-22 and XP-27 A two-chassis line stage and phono stage. Stereophile names the XP-22 its Amplification Product of the Year for 2019; the INT-25 integrated follows in 2019.Pass Labs XP-22 Preamplifier
  15. 2021 XP-32 The three-chassis line stage replaces the XP-30, with one chassis per channel and a third for control and power.Pass Labs XP-32 Reference Line Preamplifier
  16. 2025 Xs Pre 2 and HPA-1c Wayne Colburn's three-chassis Xs Pre 2, which he has called his best work, and the HPA-1c, his revision of the HPA-1 headphone amplifier.Pass Labs HPA-1c Headphone Amplifier
Read the Pass Labs story
Pass Labs INT-60 and 160.8 monoblocks in the Small Room

Nelson Pass

Nelson Pass grew up with his mother's record collection and an AM radio. As a teenager he helped assemble a Heathkit, then put together his first system from a Garrard turntable, a Radio Shack amplifier and loudspeaker boxes he made himself, and soon had the amplifier apart to improve its cooling. By his second year of college he was building his own equipment. He studied physics at the University of California, Davis, taking his degree in 1974, and worked nights at the loudspeaker maker ESS, where he assisted Dr. Oskar Heil with crossovers, woofers and cabinets. A colleague there handed him a set of semiconductor application books, and from those he taught himself circuit design.

Threshold

In December 1974, with a partner from ESS, he founded Threshold Electronics in Sacramento. Money was short in the early years, but the first amplifier, the 800A of 1975, made the company's name: it used a new biasing scheme to deliver Class A performance at 200 watts. In 1978 came Stasis, a patented circuit that let an amplifier run without the corrective feedback other designs relied on. It carried Threshold through the 1980s and was licensed by Nakamichi.

Two habits from those years never left him. The first was a change of mind about measurement: having begun by chasing the best figures, he came to prefer circuits that are linear to start with and need little correction. The second was generosity. From 1978 he published simple Class A amplifiers for people to build at home, and he has gone on sharing designs with home builders ever since. In the mid-1980s he also designed the well-reviewed Adcom GFA-555.

How Pass Labs came to be

By 1991 he wanted to build something simpler. He left Threshold and started Pass Laboratories in his home shop in northern California. He and a colleague built their own milling machines to make the casework, and his next-door neighbor was hired to help build the amplifiers; she still helps run the company. The first product, the Aleph 0 monoblock, shipped in 1992: a single-ended Class A amplifier built around power MOSFETs, which he valued for behaving much as tubes do. Stereophile named it Amplification Component of 1995, and its reviewer called it “the solid-state amplifier of the decade.”

The Aleph

The idea behind the Aleph was that everything done to a musical signal leaves its mark, so the best circuit is the one that does the least. The second generation of 1994 had just two stages of amplification where conventional designs used as many as eight, needed no adjustment, and ran single-ended all the time, helped by a current source of his own invention. It asked listeners to think differently about power: a 200-watt amplifier sounds only about twice as loud as a 30-watt one, and the Aleph 3 offered 30 watts of a quality that made the trade worthwhile.

The Alephs looked like nothing else: black boxes with heatsink fins on every side and, on the larger models, a single blue light. They ran warm, and they were built to last, with input transistors chosen so strictly that only about one in ten passed. The family ran from the Aleph 3 through the Aleph 2 and the 200-watt Aleph 1.2 monoblocks to the Aleph P preamplifier. Reviewers of the day heard no electronic signature: ease, natural timbre, a three-dimensional soundstage, tuneful bass and a sweet top end.

Supersymmetry and the X amplifiers

In 1994 Nelson Pass patented Supersymmetry, which pairs the two balanced halves of an amplifier so that their noise and distortion match and cancel at the output. It let the company build much larger amplifiers on the same simple principles. The X1000 of 1998 was the first amplifier built on it, and the X series that followed remains the mainstay of the company's power amplifiers. The XA series of 2002 joined that circuit to an Aleph-style output stage; he has described the aim as a warm, sweet X amplifier or, put the other way, a powerfully dynamic Aleph.

The amplifiers of today

The two-chassis Xs monoblocks of 2012 were developed over three years, led by listening, and what was learned from them went into the Point 8 generation of 2014: nine X and XA amplifiers, seven years in the making, with deeper Class A operation, larger heatsinks and bigger power supplies. Integrated amplifiers descended from them followed in 2015, and in 2017 the XA25, a 25-watt Class A amplifier with a single pair of output devices in each channel. These are heavy machines. The XA60.8 puts 60 watts in a chassis of 88 pounds, and Nelson Pass has said that the weight is in the heatsinks and power transformers and that, all else being equal, the amplifier with the bigger hardware seems to have the advantage.

The words reviewers use for the current amplifiers are touch, texture, delicacy and sweetness, with body, impact, authority and a huge, precise soundstage, and no hardness. Stereophile's measurements of the XA60.8 found it quiet, with far more usable power than its 60-watt rating suggests.

First Watt

Alongside Pass Labs, Nelson Pass runs First Watt, which he describes as a kitchen-table venture, where he builds small numbers of amplifiers of 25 watts or less to try ideas that fall outside the main range. What he learns there comes back. Work with unusual transistors at First Watt taught him how the character of an amplifier's distortion shapes the sense of depth in a recording, and that understanding went into the Pass Labs amplifiers.

Wayne Colburn

Wayne Colburn joined in 1994 to work on an improved preamplifier and a new phono stage, and he has designed the company's preamplifiers and phono stages ever since: the later Aleph P, the Xono, the XP line that began in 2008, and the Xs preamplifiers at the top of the range. Stereophile named his XP-22 its Amplification Product of the Year for 2019, the three-chassis XP-32 followed in 2021, and the Xs Pre 2 of 2025 is one he has called his best work. At Pearl Audio we think especially highly of his phono stages.

Built in California

Pass Labs moved from the home shop to Foresthill, California, in 1997, and in 2014 to a factory in Auburn nearly three times the size, with every operation under one roof; research stays in the original shop. Circuit boards are assembled and inspected by hand, front panels are machined nearby from solid aluminum, and every amplifier runs for three days at a constant temperature before its bias is set.

Kent English is one of the two people who manage the day-to-day running of the company, and Nelson Pass and Wayne Colburn still design the products. Pass Labs keeps parts for everything it has made, which matters for an amplifier bought to be kept.

The complete Pass Labs story and technology library

Pass Labs at Pearl Audio

Before he was a dealer, John Loranger listened at home to a pair of Pass Aleph 2 monoblocks with the Aleph P preamplifier and the Xono phono stage, and he has known Nelson Pass and Wayne Colburn for more than twenty years. Pearl Audio first carried Pass Labs around 2005 and, after some years apart, carries it again today. We carry the XA and X .8 amplifiers, the XA25, the INT-60 and INT-250 integrateds, the XP line stages and phono stages and the HPA-1c, and we can order any current Pass Labs product in silver or black. Because a Class A amplifier's rating is its Class A envelope rather than its limit, we help match the model to the loudspeaker and the room, and we deliver, place and connect the heavier pieces ourselves. Pass Labs builds to order in Auburn, California, and the factory keeps parts for every product it has made.

The Pearl Audio experience

How we work with you

A system at this level should be heard, thoughtfully matched, and properly set up. From the first audition to long-term ownership, you work with the same people, in person.

  1. 01

    Listen first

    The Pass Labs XP-27 Phono Preamplifier is not in our rooms at present. When it is the right piece for a client we arrange a demonstration unit from the manufacturer and set it up for a private session.

  2. 02

    Delivery and installation

    We deliver and install throughout the Portland area, taking care of placement, connections, ventilation and system configuration ourselves.

  3. 03

    Support for as long as you own it

    We support everything we sell for as long as you own it, whether the answer comes by phone, in your home, or through factory service.

  4. 04

    A path for what comes next

    Trade-in assistance and qualifying 100% Trade-Up options give you flexibility when your listening priorities or your system change.

Search