← Back to your LP12 build

T+A Elektroakustik · Series 200

T+A Elektroakustik HA 200

$11,490

Signature technologies

Not currently in our rooms. For a serious buyer we will often bring a piece in from the manufacturer for a private session — tell us about your system and what you are weighing it against, and we will advise.

T+A Elektroakustik · Series 200

The HA 200 is T+A's reference headphone amplifier and DAC: a Class A MOSFET output stage with six selectable output impedances, three headphone sockets, analog crossfeed and tone control, and the full T+A converter for PCM to 768 kHz and DSD to DSD1024.

Includes the FM8 remote. HDMI output with ARC is optional.

8 – 80 Ω
six selectable output impedances
700 mA
Class A operation
DSD1024
native; PCM to 768 kHz
6.5 kg
14.3 lb

Authorized T+A Elektroakustik dealer · Delivery and installation by Pearl Audio · Trade-ins welcome

The story

T+A built the HA 200 the way it builds HV-Series electronics: discrete MOSFET circuitry, no op-amps, Class A up to 700 mA, and its own 100 W analog mains section fed by two 50 W transformers. The output stage is designed to deliver high current into low-impedance planars while holding voltage for 300 Ω dynamics, and a six-position output impedance switch (8, 12, 18, 25, 40 and 80 Ω) lets you match it to whatever headphone is plugged into the 6.3 mm, 4.4 mm Pentaconn or four-pin XLR sockets. Volume, loudness and tone bypass are handled by gas-tight gold-contact relays, and an analog filter circuit provides crossfeed to move the image in front of the head.

The digital side is the same architecture as the DAC 200: a double-differential quadruple converter with four 32-bit DACs per channel for PCM to 768 kHz, and a True 1-Bit converter for DSD to DSD1024, with a de-jitter master clock and a switchable 60/120 kHz Bessel filter. Inputs include AES/EBU, two coaxial, two optical, BNC, two USB, two HDMI (stereo) and Bluetooth with aptX HD, plus RCA and XLR analog inputs. The four-pin XLR output can even drive a small power amplifier.

With T+A's Solitaire P or P-SE it forms a complete reference headphone system; the MP 200 G3 adds CD, streaming and radio over SYS-Link. We can arrange an audition in our Portland showroom and help with system matching, delivery and setup.

In March 2020 the Solitaire P headphones and the HA 200 opened a new category for T+A, built around the TPM 3100 transducer the company developed in Herford; the headphone range was built up by Conradin Amft, who became CEO of the family company in 2025. The HA 200 carries the HV voltage stage of the High Voltage series of 2013 and the separate PCM and DSD converters T+A introduced with the DAC 8 DSD in 2015. Read the T+A story →

Key technologies

  • Class A MOSFET output. Discrete, op-amp-free design in Class A up to 700 mA, with its own 100 W analog mains section.
  • Selectable output impedance. 8, 12, 18, 25, 40 or 80 Ω to match any headphone.
  • Analog crossfeed. A filter circuit places the soundstage in front of the listener.
  • Relay volume and tone. Gold-contact relays handle level and loudness and bypass the tone control when flat.
  • Path Separation DAC. Quadruple 32-bit converter for PCM to 768 kHz; True 1-Bit converter for DSD to DSD1024.
  • Three headphone outputs. 6.3 mm, 4.4 mm Pentaconn and four-pin XLR.

The Solitaire P is the headphone T+A designed the HA 200 for; the MP 200 G3 is its matching source.

Finishes

  • Alu silver anodized (43)
  • Alu black anodized (42)
Specifications
Type Headphone amplifier, D/A converter and preamplifier
Headphone outputs 6.3 mm, 4.4 mm Pentaconn, XLR 4-pin; output impedance 8 / 12 / 18 / 25 / 40 / 80 Ω
Output power Not published by T+A (Class A operation up to 700 mA)
PCM conversion Double-differential quadruple converter, four 32-bit DACs per channel, 705.6/768 kHz
DSD T+A True 1-Bit converter, native up to DSD1024 (49.2 MHz); DoP to DSD256
Frequency response 0.1 Hz – 200 kHz (+0/–3 dB)
Signal-to-noise 110 / 114 dB; distortion < 0.001 %; channel separation > 108 dB
Digital inputs 1 × AES/EBU, 2 × coaxial, 2 × optical, 1 × BNC, 2 × USB DAC, 2 × HDMI in (stereo); optional HDMI out with ARC
Bluetooth aptX HD, AAC, SBC
Analog inputs RCA 250 mV – 4.5 V / 10 kΩ; XLR 500 mV – 9 V / 20 kΩ
Tone control Bass and treble –6 to +8 dB, channel-separate; switchable loudness; analog crossfeed
Remote FM8 included
Power consumption 100 W; standby < 0.5 W
Dimensions (H × W × D) 10 × 32 × 34 cm (3.9 × 12.6 × 13.4 in)
Weight 6.5 kg (14.3 lb)
Finishes Alu silver anodized (43) or alu black anodized (42)

T+A HA 200 product page and specifications

Where it sits in the range

T+A's headphone products, least to most expensive:

The MP 200 G3 adds CD, streaming and radio to the HA 200 over SYS-Link.

Plan your T+A system with Pearl Audio

Pearl Audio is an authorized T+A dealer. We can arrange a listening session with the Solitaire headphones in our Portland showroom and help with system matching, delivery and setup. Call (503) 222-2599 or email sales@pearlaudio.com.

Signature technologies

The engineering behind the T+A Elektroakustik HA 200

T+A Elektroakustik gives its technologies names because each one solves a specific problem. Here is what each does, where it came from, why it matters in a system, and what you may hear.

Transistors run where they are most linearSince 2013

HV: high-voltage amplifier stages

T+A's HV circuits run their transistor voltage-gain stages on supply rails several times higher than ordinary solid-state designs, up to 100 V in the P 3100 HV preamplifier and up to 500 V in the M 40 HV's power stages. Each device then works over a small, linear part of its curve, as a tube does, so the circuit needs virtually no overall negative feedback. Read the deep diveClose

What it does

Most solid-state audio circuits run on low rails; Alan Sircom notes that most modern circuits run at about plus and minus 5 V. The High Voltage series, three years in development and introduced in 2012 by Siegfried Amft's account or 2013 by T+A's own, moved the voltage-gain stages to rails several times higher, with the stated aim of combining the sonic and technical advantages of tubes and transistors while avoiding the inherent disadvantages of present-day valves. In the PA 3100 HV the input is a differential cascode amplifier of individually selected audio J-FET transistors that can process signals up to 60 V peak-to-peak without distortion; the P 3100 HV runs at up to 100 V and handles 80 V peak-to-peak; the M 40 HV's power stages reach 500 V, behind a class-A input stage of 6SN7 triodes. Because each transistor works over a small, linear part of its curve, the circuit needs virtually no overall negative feedback, and bandwidth and headroom are wide: the P 3100 HV is specified from 0.5 Hz to 300 kHz. HV is used in the amplifier stages of every HV-series component, the same voltage-gain stage appears in the Series 200, the HA 200 and the Symphonia, and the PA 2500 R and PA 2000 R carry a high-voltage dual-mono design on the R-series chassis.

Why it matters in a system

An amplifier stage that stays linear without heavy feedback behaves the same from the first watt to clipping and into awkward loudspeaker loads, which is what HV owners describe as ease at volume. It is also the reason a T+A preamplifier, converter and power amplifier sound of a piece: the same voltage-gain stage sits in all of them, from the DAC 200 to the M 40 HV.

What you may hear

Jason Victor Serinus, reviewing the PA 3100 HV for Stereophile, found the midrange strong, exceptionally smooth, and all of one piece. Alan Sircom in hi-fi+ called the SDV 3100 HV extremely listenable, with extraordinary clarity and dynamics, and musically inviting.

PCM and DSD never meetSince 2015

Two converters: Quadruple PCM and True 1-bit DSD

Instead of converting DSD to PCM inside one chip, every current T+A converter carries two. PCM goes to eight 32-bit Burr-Brown sigma-delta chips, four per channel in a double-differential arrangement; DSD goes to a discrete one-bit converter of T+A's own design that never touches PCM, and relays switch between the two paths. Read the deep diveClose

What it does

T+A's converter layout dates from the DAC 8 DSD of about 2015, when Lothar Wiemann concluded that it was very difficult to preserve a true DSD signal path with ready-made chips. The PCM side is the Double-Differential-Quadruple-Converter: four 32-bit Burr-Brown sigma-delta converters per channel, run in conversion-only mode with T+A's own upsampling and filtering ahead of them, an arrangement T+A says lowers noise by 6 dB. The MP 3100 HV G3 feeds them at 352.8 or 384 kHz; the DAC 200 and PSD 3100 HV accept PCM to 768 kHz. The DSD side is the T+A True-1Bit converter, a discrete circuit that takes the native bitstream and oversamples it; T+A holds that DSD's advantages appear only when the signal is massively oversampled, and the reference converter upsamples DSD by 32 times. The DAC 200, HA 200 and SDX 3100 HV decode up to DSD 1024, or 49.2 MHz, a capability T+A introduced in the SD and SDV 3100 HV of March 2019 and calls the world's first DSD 1024-capable player; the PSD 3100 HV, MP 3100 HV G3, MP 2500 R G3, R 2500 R and Symphonia are specified to DSD 512. In 2026 T+A gave the arrangement a name, Path Separation Technology. The Symphonia uses a two-chip-per-channel Double Differential derivative of the PCM converter.

Why it matters in a system

A chip that handles DSD by first turning it into PCM, or the reverse, imposes one filter's character on both formats. Giving each its own converter means an SACD or a DSD file reaches the analog stage as the bitstream it was recorded as, and a PCM file is handled by a converter built for multi-bit data with T+A's own filters in front of it.

What you may hear

Herb Reichert, reviewing the MP 3100 HV G3 for Stereophile, wrote that the T+A's smooth, nuanced sigma-delta feels considerably different than dCS's liquidy FPGA-controlled Ring DAC, and called it CD playback at its highest imaginable level. Jim Austin heard treble that glistened, with no digital glare.

Four filters, no ringing, the listener's choiceSince 2015

Bézier oversampling filters and 56-bit DSP

T+A writes its own PCM oversampling in a signal processor instead of using the filters built into the converter chips: two FIR filters and two Bézier-polynomial filters, plus a non-oversampling mode, selectable by the owner. The Bézier filters avoid the pre- and post-ringing of conventional filters, and a third-order Bessel analog filter follows, switchable between 60 and 120 kHz. Read the deep diveClose

What it does

Every oversampling converter interpolates new samples between the ones on the disc or in the file, and the filter that does it leaves a signature; conventional linear-phase FIR filters ring before and after each transient. In the DAC 8 DSD T+A moved this work out of the converter chip and into a 56-bit signal processor running its own algorithms, and the current units offer five settings: FIR short, FIR long, Bézier/IIR, Bézier and NOS, or non-oversampling. Lothar Wiemann's point about the Bézier interpolation is that it has no pre-ringing and no post-ringing. In the reference converters a 16-times Bézier-polynomial filter takes 44.1 and 88.2 kHz material to 705.6 kHz and 48, 96 and 192 kHz material to 768 kHz before the Quadruple converter sees it. After conversion a phase-linear third-order Bessel filter, switchable between a 60 and a 120 kHz cut-off, removes what remains above the audio band without adding ringing of its own. The same processor and filter set run in the DAC 200 and HA 200, the MP 2000 R G3 and MP 2500 R G3, the R 2500 R, the PSD 3100 HV, the MP 3100 HV G3 and the SDX 3100 HV, so the choice an owner makes on a Series 200 converter is the same one offered on the reference.

Why it matters in a system

The reconstruction filter determines how a converter handles the leading edge of every note, and the ringing of a steep filter is one reason digital playback can sound hard. Letting the listener choose among FIR, Bézier and no oversampling, with an analog filter gentle enough to add nothing of its own, means the converter can be matched to the recording and to the rest of the system.

What you may hear

Jim Austin, in Stereophile on the MP 3100 HV: treble tones glisten like light reflected from the facets of a diamond, and also seem especially relaxed, with no digital glare. Craig Joyce at StereoNET called the DAC 200 a standout product that handles a wide range of music with clarity and precision.

Two mains inlets, isolated data, one clockSince 2020

Digital-analog separation and the De-Jitter Masterclock

In T+A's converters the digital and analog sections have their own power supplies and, in the HV components, their own IEC mains inlets; data crossing between them passes through ultra-fast digital isolators, so switching noise cannot reach the analog output. Incoming digital signals are reclocked in two stages against a quartz master clock before they reach the converter. Read the deep diveClose

What it does

A converter's analog output is only as quiet as the ground it shares with its digital logic. T+A's answer, which it calls the Digital Analogue Separation System in the DAC 200, is to keep the two halves apart electrically: the analog and digital mains sections are galvanically separated, each with its own transformer, and the signal and control lines between them run through ultra-fast digital isolators from Silicon Labs, with the clocks isolated as well. The HV components go further and fit two IEC inlets, so the MP 3100 HV G3 draws its digital and analog power through separate cords, and the P 3100 HV, a purely analog preamplifier, gives each channel its own inlet. The timing side is the De-Jitter Masterclock: an incoming signal first passes a phase-locked loop, then a microprocessor checks it and switches to a quartz master clock; when the signal fails T+A's criteria a second stage, the Second Jitterbug, engages and cuts residual jitter by a factor of four. The SDX 3100 HV uses two femto-second crystal oscillators feeding a multi-stage jitter-cleansing system. James Shannon of T+A says the separate AC inputs make it virtually impossible to see any kind of digital noise entering the analog output.

Why it matters in a system

Noise that leaks from a streaming board or a USB receiver into the analog stage does not sound like hiss; it sounds like a loss of depth and a hardening of the treble that is easy to blame on the recording. Isolation and reclocking are what let a T+A converter accept a laptop or a network stream and sound as quiet as it does from its own disc drive.

What you may hear

Stereophile on the R 2500 R: its DAC is in keeping with the very best modern DACs in that it is ultra-revealing and transparent, and the component doesn't call attention to itself in any way. Craig Joyce at StereoNET gave the DAC 200 a 9 out of 10 and an Applause Award.

A driver designed, machined and assembled in HerfordSince 2020

TPM planar-magnetostatic headphone transducers

The Solitaire P headphones are built around T+A's own TPM 3100 transducer, an elliptical 110 by 80 mm planar driver with an ultra-thin, ultra-light film carrying a computed conductor pattern, driven from one side only by shaped neodymium magnets. The Solitaire P-SE uses the TPM 2500 derivative; both are developed and hand-made in Herford. Read the deep diveClose

What it does

T+A entered headphones in March 2020 with the Solitaire P and the HA 200 amplifier, and chose to build the transducer rather than buy one. The TPM 3100 diaphragm is a special ultra-thin film whose conductor pattern is computed to match the magnet geometry; the magnets sit on one side only, so there is no second magnet array between the diaphragm and the ear to reflect and diffract the sound. The Solitaire P is an open design with an impedance of 80 ohms, a response from 5 Hz to 54 kHz, distortion below 0.015 percent at 100 dB and a maximum level above 130 dB; its cups are machined from a 35 mm aluminum plate on a five-axis mill, and it weighs 530 g. The Solitaire P-SE of 2021 carries the TPM 2500, a derivative of the same transducer, at 45 ohms, 8 Hz to 45 kHz and 440 g, with high-damping plastic cups. The closed, wireless Solitaire T of 2022 takes a different route: a 42 mm dynamic driver with a cellulose diaphragm, Bluetooth 5.1, hybrid noise cancelling, about 70 hours of battery and a passive wired mode. The HA 200 was designed as the amplifier for all of them: pure class A with MOS-FET transistors, no op-amps, selectable output impedance and analog crossfeed.

Why it matters in a system

A planar driver's weakness is usually the magnet array in front of it; a single-sided motor removes it, and a transducer made in-house can be matched to its amplifier. With the HA 200's selectable output impedance and class-A current to 700 mA, the headphones and the amplifier were designed as one system rather than as two products.

What you may hear

Herb Reichert, in Stereophile's Gramophone Dreams: materials, finish, and workmanship exceeded anything he had encountered, and the Solitaire P is definitely in the best-of-the-best headphone game. On the Solitaire T, Stereophile found the build quality outstanding.

Theory and application under one roofSince 1978

Designed, built and measured in Herford

Every T+A component is designed, assembled and measured at the company's own buildings in Herford, where it has been since 1988: circuit design, board layout, software, the MusicNavigator app, final assembly and a measurement protocol for every unit. Surface-mount board assembly is placed with a specialist using T+A-supplied parts; about 95 percent of production is in-house. Read the deep diveClose

What it does

T+A has occupied its own buildings in Herford since 1988 and added an administration, sales and laboratory building in 2003. A factory visit in April 2025 counted about 90 employees, 14 of them in research and development; T+A itself describes a team of fifteen designers and developers plus seven service technicians. The scope kept in-house runs from design, PCB layout and certification to assembly, measurement, operating-system programming and app development; the one step placed outside is surface-mount component placement, done by a specialist assembler using components T+A supplies, after which the boards return for final assembly and test. There are no assembly lines or automated placement machines, and nothing leaves the works without a measurement protocol. The company's own description is that it builds acoustic treasures rather than mass products, and it reports returning more than 98 percent of devices of any age to working condition when they come back for service. The engineering continuity is long: Lothar Wiemann, who joined as a student and developed the first electronics in 1982, was chief developer for 39 years before handing over to Jörg Küpper. In the United States, T+A North America in St. Marys, Georgia has handled distribution since August 2021, with service through Pyramid Audio in Austin and Audio Design and Service in Burbank.

Why it matters in a system

A product made in one place by the people who designed it can be supported for as long as its owner wants to keep it, and T+A's factory upgrades, the ASA G3 streaming boards fitted to players from 2017, are the practical form of that. It is also why a T+A system sounds consistent from the Series 200 to the HV line: the same small team designed all of it.

What you may hear

Jim Austin, in Stereophile on the MP 3100 HV: more than any other component he had had in his system, it radiated attention to detail. Michael Manousselis, who imported the brand to North America: they don't leave things to luck or to chance.

The Pearl Audio experience

How we work with you

A system at this level should be heard, thoughtfully matched, and properly set up. From the first audition to long-term ownership, you work with the same people, in person.

  1. 01

    Listen first

    The HA 200 is not in our rooms at present. When it is the right piece for a client we arrange a demonstration unit from the manufacturer and set it up for a private session.

  2. 02

    Delivery and installation

    We deliver and install throughout the Portland area, taking care of placement, connections, ventilation and system configuration ourselves.

  3. 03

    Support for as long as you own it

    We support everything we sell for as long as you own it, whether the answer comes by phone, in your home, or through factory service.

  4. 04

    A path for what comes next

    Trade-in assistance and qualifying 100% Trade-Up options give you flexibility when your listening priorities or your system change.

Search