← Back to your LP12 build

T+A Elektroakustik · R-Series

T+A Elektroakustik T+A PA 2500 R Integrated Amplifier

$15,990

Signature technologies

Not currently in our rooms. For a serious buyer we will often bring a piece in from the manufacturer for a private session — tell us about your system and what you are weighing it against, and we will advise.

T+A Elektroakustik · R-Series

The PA 2500 R is the larger of T+A's two R-Series integrated amplifiers: the PA 2000 R circuit with heat sinks twice the size and two mains supplies, good for 140 W into 8 Ω and 280 W into 4 Ω.

Includes the SRC 1 remote. T+A's November 2026 US price list refers to this model as the PA 2500 R SL.

140 W
per channel into 8 Ω (280 W into 4 Ω)
60 V/µs
slew rate
105 / 109 dB
signal-to-noise, unweighted / A-weighted
14.5 kg
32 lb

Authorized T+A Elektroakustik dealer · Advice and support from Pearl Audio · Trade-ins welcome

The story

T+A built the PA 2500 R on the same boards as the PA 2000 R, then gave it what a bigger amplifier needs: heat sinks of twice the area and a second high-frequency sine-wave power supply, so the two channels run as a true double mono design with 120,000 µF of reservoir capacitance behind them. The output stage is a linear Class AB design with very little global negative feedback, and the input stage is a cascoded differential amplifier built from hand-selected audio J-FETs rather than op-amps.

Switching is done with sealed, gas-tight gold-contact relays, for volume as well as for input and loudspeaker selection, so there is nothing to wear or corrode in the signal path. A protection circuit sits outside the signal path and compares input with output, dropping the output relays only if it sees clipping, overheating or a short. Four RCA and three XLR inputs, a headphone output and RCA and XLR pre-outs cover most systems, and an optional phono board (MM or MC) replaces one line input.

In the R-Series the PA 2500 R is the natural partner for the MP 2500 R G3 or the G 2000 R turntable, with R2-Link letting one SRC 1 remote run the whole stack. It is 16.5 cm tall, so it stacks visually with the MP 2500 R G3 rather than the low-profile PA 2000 R. We can arrange an audition in our Portland showroom and help with system matching, delivery and setup.

The R series dates from 1992, when the Pulsar electronics T+A had built since 1986 evolved into a full line and electronics began to earn the company more than loudspeakers; the late-1990s A 1530 R power amplifier had no source selection, no displays and no digital interfaces. The PA 2500 R is the larger of the two current R series integrated amplifiers, built on the PA 2000 R of 2015, and like every T+A it is designed, assembled and measured in Herford. Read the T+A story →

Key technologies

  • Double mono power supply. Two regulated high-frequency sine-wave mains units and 120,000 µF of reservoir capacitance.
  • J-FET input stage. Cascoded differential amplifier using hand-selected audio J-FETs, with no op-amps.
  • Gold-contact relays. Sealed, gas-tight relays handle volume, input and loudspeaker switching.
  • Out-of-path protection. A comparator watches input against output and only intervenes on clipping, overheating or a short circuit.
  • R2-Link. T+A's control bus lets the SRC 1 remote run the amplifier and a matching R-Series source.

The MP 2500 R G3 is the PA 2500 R's matching source; the PA 2000 R is the lower-profile step below.

Finishes

  • Silver anodized (43) brushed aluminum
  • Black anodized (42) brushed aluminum
Specifications
Type Stereo integrated amplifier, Class AB
Power output 140 W into 8 Ω, 280 W into 4 Ω, 560 W into 2 Ω (per channel)
Frequency response 1 Hz – 150 kHz (+0/–3 dB); preamplifier 0.5 Hz – 300 kHz
Distortion < 0.02 % (output stage); < 0.001 % (preamplifier)
Signal-to-noise 105 dB unweighted, 109 dB A-weighted
Damping factor > 65
Inputs 4 × RCA, 3 × XLR; optional phono MM or MC replaces one line input
Outputs Loudspeakers, headphone (50 Ω), pre-out RCA and XLR
Remote SRC 1 included; R2-Link control bus
Power consumption Max. 2,000 W; standby < 0.5 W
Dimensions (H × W × D) 16.5 × 46 × 40.5 cm (6.5 × 18.1 × 15.9 in)
Weight 14.5 kg (32.0 lb)
Finishes Silver anodized (43) or black anodized (42)

T+A PA 2500 R product page and specifications

Where it sits in the range

The R-Series is T+A's full-size line below the HV-Series. Siblings, least to most expensive:

Add the optional PHE-P/PA R phono module (MM or MC) to run the G 2000 R turntable without a separate phono stage.

Reviews

Plan your T+A system with Pearl Audio

Pearl Audio is an authorized T+A dealer. We can arrange an audition in our Portland showroom and help with system matching, delivery and setup. Call (503) 222-2599 or email sales@pearlaudio.com.

Signature technologies

The engineering behind the T+A Elektroakustik T+A PA 2500 R Integrated Amplifier

T+A Elektroakustik gives its technologies names because each one solves a specific problem. Here is what each does, where it came from, why it matters in a system, and what you may hear.

Transistors run where they are most linearSince 2013

HV: high-voltage amplifier stages

T+A's HV circuits run their transistor voltage-gain stages on supply rails several times higher than ordinary solid-state designs, up to 100 V in the P 3100 HV preamplifier and up to 500 V in the M 40 HV's power stages. Each device then works over a small, linear part of its curve, as a tube does, so the circuit needs virtually no overall negative feedback. Read the deep diveClose

What it does

Most solid-state audio circuits run on low rails; Alan Sircom notes that most modern circuits run at about plus and minus 5 V. The High Voltage series, three years in development and introduced in 2012 by Siegfried Amft's account or 2013 by T+A's own, moved the voltage-gain stages to rails several times higher, with the stated aim of combining the sonic and technical advantages of tubes and transistors while avoiding the inherent disadvantages of present-day valves. In the PA 3100 HV the input is a differential cascode amplifier of individually selected audio J-FET transistors that can process signals up to 60 V peak-to-peak without distortion; the P 3100 HV runs at up to 100 V and handles 80 V peak-to-peak; the M 40 HV's power stages reach 500 V, behind a class-A input stage of 6SN7 triodes. Because each transistor works over a small, linear part of its curve, the circuit needs virtually no overall negative feedback, and bandwidth and headroom are wide: the P 3100 HV is specified from 0.5 Hz to 300 kHz. HV is used in the amplifier stages of every HV-series component, the same voltage-gain stage appears in the Series 200, the HA 200 and the Symphonia, and the PA 2500 R and PA 2000 R carry a high-voltage dual-mono design on the R-series chassis.

Why it matters in a system

An amplifier stage that stays linear without heavy feedback behaves the same from the first watt to clipping and into awkward loudspeaker loads, which is what HV owners describe as ease at volume. It is also the reason a T+A preamplifier, converter and power amplifier sound of a piece: the same voltage-gain stage sits in all of them, from the DAC 200 to the M 40 HV.

What you may hear

Jason Victor Serinus, reviewing the PA 3100 HV for Stereophile, found the midrange strong, exceptionally smooth, and all of one piece. Alan Sircom in hi-fi+ called the SDV 3100 HV extremely listenable, with extraordinary clarity and dynamics, and musically inviting.

No potentiometer, no chip, no coupling capacitorsSince 2020

Relay volume control and the DC-coupled preamplifier

T+A sets volume by switching precision resistors with encapsulated, gas-tight gold-contact relays rather than with a potentiometer or a volume chip, in 1 dB steps on the DAC 200. In the 3100-generation preamplifiers the coupling capacitors between the input stage, the volume control and the output were removed by a board layout that compensates the transistors' temperature drift. Read the deep diveClose

What it does

A volume control is in series with everything, and the usual choices, a carbon or conductive-plastic potentiometer or an integrated-circuit attenuator, each add noise, channel imbalance or a sound of their own. T+A's HV preamplifiers and the DAC 200 instead use a ladder of precision resistors selected by sealed relays with gold contacts, so at every setting the signal passes through fixed resistors and closed metal contacts. The P 3100 HV of May 2020 went a step further. Lothar Wiemann's goal for the 3100 generation was a capacitor-free preamplifier without servo control, in pursuit of what he called black level: more quiet, fewer disturbances, a blacker background. A new and complex board layout compensates for the transistors' temperature coefficients, so the stages from input to output are DC-coupled with no coupling capacitors and remain, in T+A's words, completely voltage and temperature stable. The PA 3100 HV shares the DC-coupled preamplifier section, which along with its VU meters and a redesigned mains section distinguishes it from the PA 3000 HV; the PSD 3100 HV and SDX 3100 HV carry the same class-A discrete HV preamplifier with relay volume; and the PA 2000 R and PA 2500 R use relay volume on the R-series chassis.

Why it matters in a system

A preamplifier's job is to lose nothing, and capacitors and potentiometers are where most of the loss happens: at low volume, where most listening is done, and in the lowest octaves, which coupling capacitors roll off. Relay switching and DC coupling are why the HV preamplifiers are described in terms of silence between the notes rather than any tonal character.

What you may hear

Matthew Clott, reviewing the PSD 3100 HV for The Absolute Sound: it's not a component you evaluate; it's a component you listen to, and highly, highly recommended. Jason Victor Serinus found the PA 3100 HV meticulously engineered and beautifully made.

The first watts in class A, with power in reserveSince 2017

Class-A regions, High Current mode and external supplies

T+A's HV power stages idle in class A for the first tens of watts before passing into class AB: 10 to 20 W in the PA 3100 HV, 20 to 25 W in the PA 2500 R, 60 W in the M 40 HV, and beyond 75 W in the A 3100 HV's High Current mode. The optional PS 3000 HV and PS 3100 HV take over the output stage's power supply through a heavy umbilical. Read the deep diveClose

What it does

A class-AB amplifier biased deep into class A plays most music, most of the time, without its output devices switching off, and keeps the reserve for peaks. The PA 3100 HV delivers 300 W into 8 ohms and 500 W into 4; its VU meters read watts into 4 ohms. The PA 2500 R is, in The Absolute Sound's description, a dual-mono, fully balanced, high-voltage design with a class-AB output stage biased into class A for the first 20 to 25 watts. The M 40 HV runs in class A to 60 W on its way to 550 W into 8 ohms and 1,000 W into 4. The A 3100 HV of 2026 offers two modes: High Power, 500 W of class AB, and High Current, which trades about half the rated power for greater current delivery and extends the true class-A region beyond 75 watts, depending on the speaker load. For the integrated and the stereo amplifier T+A offers a separate supply: the PS 3000 HV provided an extra 1,800 W of supply power, and the PS 3100 HV of September 2026 carries a 1,200 VA transformer and 24 custom capacitors totalling 240,000 µF, up to 1,200 joules; it feeds the output stages while the amplifier's own supply feeds the input and HV stages.

Why it matters in a system

A loudspeaker with a difficult impedance asks an amplifier for current more than for watts, and class-A bias and a stiff supply are what keep the sound unchanged when it does. James Shannon's own description of the external supply is modest: it makes an audible difference with more challenging loads, and it will not change the tonal balance.

What you may hear

Serinus on the PA 3100 HV in Stereophile: an excellent, meticulously engineered, beautifully made integrated amplifier that seems tailor-made for many audiophiles. Hi-Fi News on the M 40 HV: remarkably well-mannered power amps that are not going to make your listening space uncomfortably muggy.

Theory and application under one roofSince 1978

Designed, built and measured in Herford

Every T+A component is designed, assembled and measured at the company's own buildings in Herford, where it has been since 1988: circuit design, board layout, software, the MusicNavigator app, final assembly and a measurement protocol for every unit. Surface-mount board assembly is placed with a specialist using T+A-supplied parts; about 95 percent of production is in-house. Read the deep diveClose

What it does

T+A has occupied its own buildings in Herford since 1988 and added an administration, sales and laboratory building in 2003. A factory visit in April 2025 counted about 90 employees, 14 of them in research and development; T+A itself describes a team of fifteen designers and developers plus seven service technicians. The scope kept in-house runs from design, PCB layout and certification to assembly, measurement, operating-system programming and app development; the one step placed outside is surface-mount component placement, done by a specialist assembler using components T+A supplies, after which the boards return for final assembly and test. There are no assembly lines or automated placement machines, and nothing leaves the works without a measurement protocol. The company's own description is that it builds acoustic treasures rather than mass products, and it reports returning more than 98 percent of devices of any age to working condition when they come back for service. The engineering continuity is long: Lothar Wiemann, who joined as a student and developed the first electronics in 1982, was chief developer for 39 years before handing over to Jörg Küpper. In the United States, T+A North America in St. Marys, Georgia has handled distribution since August 2021, with service through Pyramid Audio in Austin and Audio Design and Service in Burbank.

Why it matters in a system

A product made in one place by the people who designed it can be supported for as long as its owner wants to keep it, and T+A's factory upgrades, the ASA G3 streaming boards fitted to players from 2017, are the practical form of that. It is also why a T+A system sounds consistent from the Series 200 to the HV line: the same small team designed all of it.

What you may hear

Jim Austin, in Stereophile on the MP 3100 HV: more than any other component he had had in his system, it radiated attention to detail. Michael Manousselis, who imported the brand to North America: they don't leave things to luck or to chance.

The Pearl Audio experience

How we work with you

A system at this level should be heard, thoughtfully matched, and properly set up. From the first audition to long-term ownership, you work with the same people, in person.

  1. 01

    Listen first

    The T+A PA 2500 R Integrated Amplifier is not in our rooms at present. When it is the right piece for a client we arrange a demonstration unit from the manufacturer and set it up for a private session.

  2. 02

    Placement and setup advice

    Ask us about placement, connections, ventilation and system configuration, and about delivery.

  3. 03

    Support for as long as you own it

    We support everything we sell for as long as you own it, whether the answer comes by phone, in the shop, or through factory service.

  4. 04

    A path for what comes next

    Trade-in assistance and qualifying 100% Trade-Up options give you flexibility when your listening priorities or your system change.

Search