← Back to your LP12 build

T+A Elektroakustik · HV-Series

T+A Elektroakustik T+A M 40 HV Hybrid Mono Power Amplifiers (pair)

$68,000 per pair

Signature technologies

Not currently in our rooms. For a serious buyer we will often bring a piece in from the manufacturer for a private session — tell us about your system and what you are weighing it against, and we will advise.

T+A Elektroakustik · HV-Series

The M 40 HV is T+A's 40th-anniversary monoblock: a hybrid with a 6SN7 valve input stage, a Class A high-voltage J-FET gain stage and twenty bipolar output transistors, rated at 550 W into 8 Ω and 1,000 W into 4 Ω.

Price is for a pair of mono amplifiers. Anniversary Edition in silver or titanium lacquer.

550 W
into 8 Ω (1,000 W into 4 Ω)
60 W
pure Class A
> 114 dB
signal-to-noise
52 kg
114.6 lb each
Options and pricing

Authorized T+A Elektroakustik dealer · Delivery and installation by Pearl Audio · Trade-ins welcome

The story

T+A marked forty years with a monoblock that borrows from every stage of its history. The input is a symmetrical differential amplifier in an all-valve cascode arrangement using 6SN7 triodes in Class A. The voltage amplifier behind it is a high-voltage J-FET stage with triode-like characteristics, also in pure Class A. MOSFET drivers feed twenty ring-emitter bipolar output transistors, and a 180,000 µF reservoir stands behind them. The result is up to 60 W of pure Class A, 250 W in Class AB, and 550 W into 8 Ω or 1,000 W into 4 Ω in High Power mode.

The numbers that matter for difficult loudspeakers are the damping factor of over 115, a 65 V/µs slew rate and distortion below 0.009 %. A thermal processor manages the output stages so the amplifier can sit in Class A for normal listening and still have the headroom for anything. Inputs are RCA and both three-pin and four-pin XLR.

A pair of M 40 HVs with the P 3100 HV or PSD 3100 HV preamplifier is T+A's reference amplification. Each weighs 52 kg and stands 56 cm tall, so plan floor space rather than shelf space. We can arrange an audition in our Portland showroom and help with system matching, delivery and setup.

For its fortieth anniversary in 2018 T+A launched the M 40 HV as an Anniversary Edition, a hybrid mono amplifier with 6SN7 triodes at its input, and kept it in production because of demand. It descends from the High Voltage series of 2013, built on the idea of running transistor gain stages at supply voltages several times higher than usual, and like every T+A it is built in Herford, where the company has been since Siegfried Amft founded it in 1978. Read the T+A story →

Key technologies

  • Valve input stage. Symmetrical differential amplifier in an all-valve cascode with 6SN7 triodes, Class A.
  • HV J-FET voltage amplifier. High-voltage J-FET stage with triode-like transfer characteristics, pure Class A.
  • Twenty ring-emitter outputs. MOSFET drivers feeding twenty bipolar output transistors.
  • Thermal processor control. Intelligent management of the output stages' operating point.
  • 180,000 µF reservoir. Supply capacity for 1,000 W into 4 Ω.

The P 3100 HV and PSD 3100 HV are the preamplifiers built for the M 40 HV; the PA 3100 HV is the integrated step below.

Finishes

  • Silver lacquer (47) case; heat sinks black (42)
  • Titanium lacquer (64) case; heat sinks black (42)

HV-Series units ship in heavy-duty flight cases.

Specifications
Type Hybrid mono power amplifier (valve input, transistor output)
Power output 550 W into 8 Ω, 1,000 W into 4 Ω nominal; peak 570 W / 1,070 W (High Power mode)
Class A Up to 60 W pure Class A; up to 250 W Class AB
Frequency response 1 Hz – 150 kHz (+0/–3 dB)
Distortion < 0.009 % (5 W, 4 Ω, 1 kHz)
Signal-to-noise > 114 dB
Damping factor > 115; slew rate 65 V/µs
Inputs RCA, XLR 3-pin, XLR 4-pin
Valves 6SN7 (input stage)
Reservoir capacity 180,000 µF
Power consumption 1,500 W max.; standby < 0.5 W
Dimensions (H × W × D) 56 × 36 × 47 cm (22.0 × 14.2 × 18.5 in)
Weight 52 kg (114.6 lb) each
Finishes Silver lacquer (47) or titanium lacquer (64); heat sinks black (42)
Sold as Pair of mono amplifiers; price shown is for the pair

T+A M 40 HV product page and specifications

Where it sits in the range

The HV-Series is T+A's reference line. Siblings, least to most expensive:

The P 3100 HV or PSD 3100 HV is the matching preamplifier.

Plan your T+A system with Pearl Audio

Pearl Audio is an authorized T+A dealer. We can arrange an audition in our Portland showroom and help with system matching, delivery and setup. Call (503) 222-2599 or email sales@pearlaudio.com.

Signature technologies

The engineering behind the T+A Elektroakustik T+A M 40 HV Hybrid Mono Power Amplifiers (pair)

T+A Elektroakustik gives its technologies names because each one solves a specific problem. Here is what each does, where it came from, why it matters in a system, and what you may hear.

Transistors run where they are most linearSince 2013

HV: high-voltage amplifier stages

T+A's HV circuits run their transistor voltage-gain stages on supply rails several times higher than ordinary solid-state designs, up to 100 V in the P 3100 HV preamplifier and up to 500 V in the M 40 HV's power stages. Each device then works over a small, linear part of its curve, as a tube does, so the circuit needs virtually no overall negative feedback. Read the deep diveClose

What it does

Most solid-state audio circuits run on low rails; Alan Sircom notes that most modern circuits run at about plus and minus 5 V. The High Voltage series, three years in development and introduced in 2012 by Siegfried Amft's account or 2013 by T+A's own, moved the voltage-gain stages to rails several times higher, with the stated aim of combining the sonic and technical advantages of tubes and transistors while avoiding the inherent disadvantages of present-day valves. In the PA 3100 HV the input is a differential cascode amplifier of individually selected audio J-FET transistors that can process signals up to 60 V peak-to-peak without distortion; the P 3100 HV runs at up to 100 V and handles 80 V peak-to-peak; the M 40 HV's power stages reach 500 V, behind a class-A input stage of 6SN7 triodes. Because each transistor works over a small, linear part of its curve, the circuit needs virtually no overall negative feedback, and bandwidth and headroom are wide: the P 3100 HV is specified from 0.5 Hz to 300 kHz. HV is used in the amplifier stages of every HV-series component, the same voltage-gain stage appears in the Series 200, the HA 200 and the Symphonia, and the PA 2500 R and PA 2000 R carry a high-voltage dual-mono design on the R-series chassis.

Why it matters in a system

An amplifier stage that stays linear without heavy feedback behaves the same from the first watt to clipping and into awkward loudspeaker loads, which is what HV owners describe as ease at volume. It is also the reason a T+A preamplifier, converter and power amplifier sound of a piece: the same voltage-gain stage sits in all of them, from the DAC 200 to the M 40 HV.

What you may hear

Jason Victor Serinus, reviewing the PA 3100 HV for Stereophile, found the midrange strong, exceptionally smooth, and all of one piece. Alan Sircom in hi-fi+ called the SDV 3100 HV extremely listenable, with extraordinary clarity and dynamics, and musically inviting.

The first watts in class A, with power in reserveSince 2017

Class-A regions, High Current mode and external supplies

T+A's HV power stages idle in class A for the first tens of watts before passing into class AB: 10 to 20 W in the PA 3100 HV, 20 to 25 W in the PA 2500 R, 60 W in the M 40 HV, and beyond 75 W in the A 3100 HV's High Current mode. The optional PS 3000 HV and PS 3100 HV take over the output stage's power supply through a heavy umbilical. Read the deep diveClose

What it does

A class-AB amplifier biased deep into class A plays most music, most of the time, without its output devices switching off, and keeps the reserve for peaks. The PA 3100 HV delivers 300 W into 8 ohms and 500 W into 4; its VU meters read watts into 4 ohms. The PA 2500 R is, in The Absolute Sound's description, a dual-mono, fully balanced, high-voltage design with a class-AB output stage biased into class A for the first 20 to 25 watts. The M 40 HV runs in class A to 60 W on its way to 550 W into 8 ohms and 1,000 W into 4. The A 3100 HV of 2026 offers two modes: High Power, 500 W of class AB, and High Current, which trades about half the rated power for greater current delivery and extends the true class-A region beyond 75 watts, depending on the speaker load. For the integrated and the stereo amplifier T+A offers a separate supply: the PS 3000 HV provided an extra 1,800 W of supply power, and the PS 3100 HV of September 2026 carries a 1,200 VA transformer and 24 custom capacitors totalling 240,000 µF, up to 1,200 joules; it feeds the output stages while the amplifier's own supply feeds the input and HV stages.

Why it matters in a system

A loudspeaker with a difficult impedance asks an amplifier for current more than for watts, and class-A bias and a stiff supply are what keep the sound unchanged when it does. James Shannon's own description of the external supply is modest: it makes an audible difference with more challenging loads, and it will not change the tonal balance.

What you may hear

Serinus on the PA 3100 HV in Stereophile: an excellent, meticulously engineered, beautifully made integrated amplifier that seems tailor-made for many audiophiles. Hi-Fi News on the M 40 HV: remarkably well-mannered power amps that are not going to make your listening space uncomfortably muggy.

Theory and application under one roofSince 1978

Designed, built and measured in Herford

Every T+A component is designed, assembled and measured at the company's own buildings in Herford, where it has been since 1988: circuit design, board layout, software, the MusicNavigator app, final assembly and a measurement protocol for every unit. Surface-mount board assembly is placed with a specialist using T+A-supplied parts; about 95 percent of production is in-house. Read the deep diveClose

What it does

T+A has occupied its own buildings in Herford since 1988 and added an administration, sales and laboratory building in 2003. A factory visit in April 2025 counted about 90 employees, 14 of them in research and development; T+A itself describes a team of fifteen designers and developers plus seven service technicians. The scope kept in-house runs from design, PCB layout and certification to assembly, measurement, operating-system programming and app development; the one step placed outside is surface-mount component placement, done by a specialist assembler using components T+A supplies, after which the boards return for final assembly and test. There are no assembly lines or automated placement machines, and nothing leaves the works without a measurement protocol. The company's own description is that it builds acoustic treasures rather than mass products, and it reports returning more than 98 percent of devices of any age to working condition when they come back for service. The engineering continuity is long: Lothar Wiemann, who joined as a student and developed the first electronics in 1982, was chief developer for 39 years before handing over to Jörg Küpper. In the United States, T+A North America in St. Marys, Georgia has handled distribution since August 2021, with service through Pyramid Audio in Austin and Audio Design and Service in Burbank.

Why it matters in a system

A product made in one place by the people who designed it can be supported for as long as its owner wants to keep it, and T+A's factory upgrades, the ASA G3 streaming boards fitted to players from 2017, are the practical form of that. It is also why a T+A system sounds consistent from the Series 200 to the HV line: the same small team designed all of it.

What you may hear

Jim Austin, in Stereophile on the MP 3100 HV: more than any other component he had had in his system, it radiated attention to detail. Michael Manousselis, who imported the brand to North America: they don't leave things to luck or to chance.

The Pearl Audio experience

How we work with you

A system at this level should be heard, thoughtfully matched, and properly set up. From the first audition to long-term ownership, you work with the same people, in person.

  1. 01

    Listen first

    The T+A M 40 HV Hybrid Mono Power Amplifiers (pair) is not in our rooms at present. When it is the right piece for a client we arrange a demonstration unit from the manufacturer and set it up for a private session.

  2. 02

    Delivery and installation

    We deliver and install throughout the Portland area, taking care of placement, connections, ventilation and system configuration ourselves.

  3. 03

    Support for as long as you own it

    We support everything we sell for as long as you own it, whether the answer comes by phone, in your home, or through factory service.

  4. 04

    A path for what comes next

    Trade-in assistance and qualifying 100% Trade-Up options give you flexibility when your listening priorities or your system change.

Search