← Back to your LP12 build

Hana · M Series

Hana ML

$1,200

Trade-in availableSignature technologiesThe Hana story

Not currently in our rooms. For a serious buyer we will often bring a piece in from the manufacturer for a private session — tell us about your system and what you are weighing it against, and we will advise.

Hana · M Series

Hana's deluxe low-output moving coil: a nude Microline stylus, cryogenically treated Alnico motor and damped Delrin body, with the same low-impedance generator used in the Umami Blue.

0.4 mV
output
Microline
nude diamond stylus
2.0 g
tracking force
9.5 g
weight

Authorized Hana dealer · Delivery and installation by Pearl Audio · Trade-ins welcome

The story

The M Series is Hana's deluxe line, and it brings four upgrades over the S Series. The stylus is a nude Microline tip that mimics the cutting stylus and sits more precisely in the groove. The body is injection-molded Delrin (POM) with an integral machined brass cap for constrained-layer damping and threaded mounting fittings; the cap takes the weight to 9.5 g for better coupling to a wider range of arms. The pure-iron magnetic circuit, including the front yoke and center and rear parts, is cryogenically treated for a more linear magnetic field, and the coils are wound with high-purity copper wire. The magnet is Alnico, the cantilever aluminum. The ML's generator is the low-impedance design shared with the Umami Blue, wound with very high-purity copper for an 8 Ω coil and 0.4 mV output; Hana says it was adopted to match a broader range of phono preamps.

Herb Reichert in Stereophile called the ML an artfully engineered cartridge that loves all music and a fantastic bargain, and Michael Fremer at Analog Planet found it a clear leap beyond the SL. The Audio Beatnik simply found it a joy to use. The ML needs an MC phono stage with about 60 to 66 dB of gain or a step-up transformer, loaded above 100 Ω; 100 to 200 Ω is a good place to start. At 9.5 g and 10 × 10⁻⁶ cm/dyne compliance it suits medium-mass tonearms, and the threaded brass cap makes mounting simple. The Microline tip wants precise alignment and an arm with adjustable height, and it rewards clean records. If your phono stage has only MM gain, the MH is the same cartridge with 2 mV of output.

The ML sits above the SL MK II and below the Umami Blue, whose low-impedance generator it shares. On a trade-in, Musical Surroundings takes 30% off a new ML or MH for a worn one, 20% off for any other Hana, Clearaudio or DS Audio cartridge, and 10% off for any other brand.

The M Series of October 2018 introduced the ideas that define the current Hana range: a nude Microline stylus, a Delrin body with a brass cap, cryogenic treatment of the magnetic circuit and, on the ML, an 8-ohm generator wound with thicker copper. hi-fi+ named the ML its Phono Cartridge of the Year for 2019, and every one is still built by hand at Excel Sound, the Yokohama company Masao Okada founded in 1970. Read the Hana story →

Key technologies

The MH is the same cartridge wound for a moving-magnet input; the Umami Blue shares the ML's generator.

Specifications
Type Low-output moving coil (MC)
Output 0.4 mV at 1 kHz
Internal impedance 8 Ω at 1 kHz
Recommended load Greater than 100 Ω
Tracking force 2.0 g (70 µm trackability at 2 g)
Compliance 10 × 10⁻⁶ cm/dyne
Weight 9.5 g (16.7 mm tall)
Stylus Nude Microline diamond
Cantilever Aluminum
Magnet Alnico, cryogenically treated pure-iron magnetic circuit
Frequency response 12 Hz – 45 kHz
Channel separation / balance 30 dB at 1 kHz / within 1 dB
Body Delrin (POM) with machined brass cap and threaded mounts, black
Also available Hana MH (2 mV high-output version for MM phono inputs)

Hana ML product page and specifications

Rebuilds and trade-in

Hana trade-in and re-tip exchange (Musical Surroundings). Trade in a worn MH or ML and a new one is 30% off ($840). Trade in any other Hana, Clearaudio or DS Audio cartridge and it is 20% off ($960); any other brand's cartridge earns 10% off ($1,080).

Hana re-tip exchange — MH or ML for a new ML $840 (Hana does not retip; your worn cartridge is exchanged for a new one at 30% off)
Trade in your Hana MH $840 after trade-in (credit $360)
Trade in your Hana ML $840 after trade-in (credit $360)
Trade in your Hana EH $960 after trade-in (credit $240)
Trade in your Hana EL $960 after trade-in (credit $240)
Trade in your Hana EH MK II $960 after trade-in (credit $240)
Trade in your Hana EL MK II $960 after trade-in (credit $240)
Trade in your Hana SH $960 after trade-in (credit $240)
Trade in your Hana SL $960 after trade-in (credit $240)
Other Hana cartridges 6 more models qualify; use the trade-in selector on this page or ask us

The 30% re-tip exchange is Hana's replacement for retipping: a worn cartridge of the same series (working or not) is exchanged for a new one. Trade-ins of Musical Surroundings brands (Hana, Clearaudio, DS Audio) need an RA number and must arrive within 30 days of the invoice; other brands need an emailed photograph first. The Umami Blue and Red take other-brand trades only when the trade is worth more than $1,000 retail. Verified 2026-10-28. Source: Hana dealer price list, January 2026 (Musical Surroundings).

Where it sits in the range

The Hana cartridges Pearl Audio stocks, from least to most expensive:

Plan your Hana system with Pearl Audio

Pearl Audio is an authorized Hana dealer. Arrange an audition in our Portland showroom, and ask us about trade-in pricing against your current cartridge. Call (503) 222-2599 or email sales@pearlaudio.com.

Signature technologies

The engineering behind the Hana ML

Hana gives its technologies names because each one solves a specific problem. Here is what each does, where it came from, why it matters in a system, and what you may hear.

Elliptical, Shibata, Microline; aluminum, boron, diamondSince 2015

The stylus and cantilever ladder

Each step up the Hana range changes the two parts that touch the record: the diamond and the rod that carries it. The E Series uses an elliptical stylus on an aluminum cantilever, the S a nude Shibata on tapered aluminum, the M a nude Microline on aluminum, the Umami Blue and Red a Microline on solid boron, and the Umami Black a Microline on a diamond cantilever. Read the deep diveClose

What it does

The stylus profile decides how much of the groove wall the diamond reads. The E Series carries a synthetic elliptical, the simplest shape and the one most tolerant of setup. The S Series moves to a nude natural-diamond Shibata, a line-contact profile with a taller, narrower footprint; Hi-Fi News credits Excel Sound with mounting a Shibata on a crimped, stiffened alloy cantilever to lower tip mass. The M Series and the three Umami models use a nude Microline, the narrowest line contact, which Hana describes as mimicking the cutting stylus and fitting more precisely into the groove. The cantilever ladder runs alongside. The E and M use aluminum pipe; the S Series MK II of 2024 and the E Series MK II of 2026 use a tapered aluminum rod that Hana says is stiffer and has less effective mass at the tip, and Masao Okada called it the biggest change in the SL MK II. The Umami Blue and Red carry the Microline on solid boron, which Hana's brochure describes as about as hard as diamond and able to carry fine detail and micro-dynamics to the generator without loss. The Umami Black of 2025 is the first Hana with a diamond cantilever. The cantilever and stylus assemblies come from Orbray, formerly Adamant Namiki.

Why it matters in a system

A stiffer, lighter cantilever bends less between the stylus and the coils, so more of what the diamond traces reaches the generator and less is lost as flex or stored as resonance. A narrower line contact reads more of the high-frequency detail cut into the groove and wears records less, provided it is aligned with care. Line-contact profiles reward a well-set tonearm and clean records, which is part of what Pearl does at installation.

What you may hear

Andre Jennings of The Absolute Sound found the Shibata SL and SH to be models of sonic purity with very low perceived distortion. Herb Reichert of Stereophile wrote that the SL excavated more microscale information than the EL, especially in the high frequencies, and The Absolute Sound heard the tapered-cantilever SL MK II move a few steps closer to neutral.

And the OKD generator of the Umami BlackSince 2015

Alnico, samarium-cobalt and neodymium magnets

Most Hanas are built around Alnico, the aluminum-nickel-cobalt magnet of classic cartridges, chosen for its tonal character rather than its strength. The Umami Red moves to samarium-cobalt, and the Umami Black to a neodymium magnet inside a new generator, named OKD for Masao Okada, whose yoke both shapes the field and supports the diamond cantilever. Read the deep diveClose

What it does

A moving-coil cartridge is a tiny generator: coils on an armature swing in the field of a fixed magnet, and the magnet's material sets both the strength and the shape of that field. Hana's E, S and M Series and the Umami Blue use Alnico, which Musical Surroundings describes as less powerful than modern magnets, and which Hana keeps for the way it sounds; The Absolute Sound called the result a meeting of old and new. The EL MK II of 2026 retains the classic Alnico magnet behind its updated coil. The Umami Red of 2020 is the first Hana to use a rare-earth magnet, samarium-cobalt, in a pure-iron magnetic circuit with a square-plate Permalloy armature. The Umami Black of 2025 goes further: a neodymium N40 magnet, a 2 mm square hybrid carbon-permalloy armature hand-wound with 30-micron 4N copper, and the OKD generator, in which the rear pole piece and yoke are made as a single part and an inverted-U front yoke supports the cantilever while aligning the field, so that the mechanical path from the stylus and the magnetic path through the coils are handled by the same structure. Hana says the Black is much more than an Umami Red with a diamond cantilever, and its output is 0.3 mV at 5 ohms.

Why it matters in a system

The magnet decides how much signal the coils make for a given motion and how linear that field is across the coil's travel. Alnico gives Hana a sound many listeners associate with the great cartridges of the 1960s and 1970s at a modest price; rare-earth magnets give the Umami Red and Black more field from the same space, and the OKD yoke brings resonance control and field alignment into one part.

What you may hear

Herb Reichert of Stereophile linked the Alnico SL to a black background, seductively rendered top octaves and exquisite inner detail. Andre Jennings of The Absolute Sound found the Umami Black neither warm nor rolled-off, leaning toward clarity, resolution and tone color rather than ultimate bass slam.

Yokes, pole pieces and pins frozen near absolute zeroSince 2018

Cryogenic cold annealing

Since the M Series of 2018, Hana has frozen the iron parts of the magnetic circuit, the front yoke, pole pieces and rear magnetic parts, and the gold-plated terminal pins, to near absolute zero. Hana calls the process cold annealing and says it gives a more even magnetic field and better conductivity. It now covers the entire range. Read the deep diveClose

What it does

Cryogenic treatment takes a finished metal part down to a temperature near absolute zero and brings it back slowly. Hana's description is that the process restructures the metal at the molecular level, relaxing the stresses left by machining and forming so that the grain is more uniform. In a cartridge the parts that matter are the ones that carry magnetic flux, the yokes and pole pieces around the coils, and the ones that carry the signal out, the terminal pins. Hana introduced the treatment on the ML and MH in October 2018, applying it to the front yoke and the center and rear magnetic parts, and the press release claimed a more precise and controlled flux field for greater linearity. The Umami Red of 2020 extended it to the yokes, the pole piece and the 24-karat gold-plated pins, and the Umami Black treats the whole generator and its gold-plated brass pins. The S Series MK II of 2024 brought cryo-treated yokes, pole pieces and pins to the SL, SH and SL Mono, and the E Series MK II of 2026 completed the range; Hana's own page for the EL MK II says the same treatment is used across the Umami Series and the entire Hana range.

Why it matters in a system

The field in the gap is what the coils move through, and any unevenness in it becomes distortion that no phono stage can remove. A yoke with a more uniform grain carries flux more evenly, and a pin with better conductivity loses less of a signal that is only a few tenths of a millivolt. The treatment is one reason the M Series and everything after it measure and sound more alike across the range.

What you may hear

Alan Sircom of hi-fi+ found the ML and MH brilliant in detail resolution and beautiful in tonal balance, and Herb Reichert of Stereophile called the ML a stunning-sounding, artfully engineered phono invention. In the Umami Black, AnalogPlanet reported the treated pins are intended for enhanced conductivity and reduced distortion.

Thicker wire, fewer turns, quieter signalSince 2018

The 8-ohm pure-copper generator

The original Hana coils were 15-micron copper wound to 30 ohms. With the ML in 2018 Hana rewound the generator with 30-micron, 4N high-purity copper and fewer turns, dropping impedance to 8 ohms at 0.4 mV. The same generator went into the Umami Blue, the SL MK II and the EL MK II, and it lets the cartridge be loaded at 80 to 100 ohms. Read the deep diveClose

What it does

A moving-coil cartridge's output and impedance are both set by the coil: more turns of thinner wire give more voltage but more resistance, and the resistance is a noise source in its own right. The 2015 EL and SL were wound with 15-micron four-nines copper to 30 ohms and 0.5 mV. For the ML of October 2018, Hana doubled the wire diameter to 30 microns, kept the purity, and reduced the turns, so the coil measures 8 ohms and delivers 0.4 mV. Garth Leerer of Musical Surroundings told Stereophile that the 8-ohm coil improves signal-to-noise and allows loading of 80 to 100 ohms, where most moving-coil phono stages are happiest. Hana describes the ML's generator as the same low-impedance unit used in the Umami Blue, wound with very high-purity copper, and its page for the EL MK II says the 8-ohm coil design was first developed for the ML and later used in the SL MK II. The Umami Red and Black use their own windings of 30-micron 4N copper at 6 and 5 ohms. Across the current low-output models the recommended minimum loads fall between 50 and 100 ohms, which also suits current-drive and transimpedance phono inputs that want a low source impedance.

Why it matters in a system

Impedance is the number that decides how a cartridge and a phono stage get along. A 30-ohm coil wants a load above 400 ohms and gives up some noise floor; an 8-ohm coil runs quieter, works into a wider range of inputs, including step-up transformers and current-mode stages, and keeps the loading question simple. It is why the SL MK II and EL MK II specify 0.4 mV where their predecessors specified 0.5.

What you may hear

Herb Reichert of Stereophile wrote that the ML presented a dazzling display of avant-garde invention with unusual force and extremely pure transients, and he found the Umami Blue so persuasive that after a week he was ready to propose marriage.

All Hana technologies and the company story

The Hana story

Moving-coil cartridges designed by Masao Okada and built by hand at Excel Sound in Yokohama, from the EL to the Umami.

Founded 1970 in Tokyo, Japan; Excel Sound now builds every Hana in Yokohama by Masao Okada · hanacartridges.com

Milestones

  1. 1970 Excel Sound Corporation Masao Okada, who began researching phono cartridge design in 1964, opens the Excel factory in Tokyo. The company's first products under its own name are the ES-70 line, initially six models; today it works from Yokohama.
  2. 1975 The OEM years From 1975 through the 1980s Excel builds moving-magnet cartridges for Pioneer, Trio (Kenwood), Sansui and Sanyo, more than 50,000 a month at the peak of the vinyl boom, and later moving coils for Sumiko and other brands that keep their supplier anonymous.
  3. 1982 Surviving the compact disc As LP demand falls, Excel keeps a small OEM cartridge business and diversifies into low-priced audio and video accessories, which carries the company through the years vinyl was declared dead.
  4. 2015 Hana Hiroshi Ishihara of Youtek reconnects with Okada and the Hana line, meaning brilliant and gorgeous, is developed for export: the elliptical EL and EH and the Shibata SL and SH, each in low- and high-output versions. Stereophile reviews the EL in August 2016; The Absolute Sound covers all four in March 2017.Hana EL
  5. 2018 SL Mono and the M Series The SL Mono adds a mono cartridge in the spring, and in October the ML and MH introduce the Microline stylus, the Delrin-and-brass body, cryogenic treatment and the 8-ohm pure-copper generator. hi-fi+ names the ML Phono Cartridge of the Year for 2019.
  6. 2020 Umami Red Announced August 3 and on sale September 22 at $3,950: boron cantilever, samarium-cobalt magnet, a Duralumin Auricle body with ebony inlay and red Urushi lacquer. hi-fi+ Cartridge of the Year 2020 and Stereophile Class A.Hana Umami Red
  7. 2023 Umami Blue The Red's body and boron cantilever over the ML's Alnico generator, at $2,500, with a white POM inlay and blue enamel. The Absolute Sound gives it a Golden Ear Award.Hana Umami Blue
  8. 2024 S Series MK II The SL MK II, SH MK II and SL Mono MK II arrive in September at $850 with a tapered aluminum cantilever, the 8-ohm generator, cryogenic treatment and the M-Series body. The SH MK II goes on to win hi-fi+'s 2026 cartridge award.Hana SL MK II
  9. 2025 Umami Black Announced September 3 at $11,500: the first Hana with a diamond cantilever, a neodymium magnet and the OKD generator named for Okada, in black Urushi. In October an Umami Fest in Healdsburg, California gathers participants from six countries, with Okada present.Hana Umami Black
  10. 2026 E Series MK II On September 1 the EL MK II and EH MK II, at $550, replace the original entry models with the M-Series body, cryogenic treatment and, on the EL, the 8-ohm generator. Okada still designs every Hana and his builders still train for five to ten years.
Read the Hana story
Hana Umami Red

Masao Okada began researching phono cartridge design in 1964 and opened the Excel factory in Tokyo in 1970; the company he founded, Excel Sound Corporation, works today from Yokohama. Its first products under its own name were the ES-70 line, initially six models. The business that followed was mostly anonymous. From 1975 through the 1980s Excel built moving-magnet cartridges for Pioneer, Trio (Kenwood), Sansui and Sanyo, and at the peak of the first vinyl boom it was shipping more than 50,000 units a month, which Hi-Fi News later summarized as once the go-to supplier of high-quality moving magnets. Moving-coil designs followed, and the company became the builder of cartridges for Sumiko, with different magnets, yokes and coil formers from anything it would later sell as its own.

Demand for records fell after the compact disc arrived in 1982. Excel kept a small cartridge business for brands that preferred not to name their supplier and diversified into low-priced audio and video accessories, which is how it survived the years when vinyl was declared dead. In 2015 Hiroshi Ishihara of Youtek Corporation reconnected with Okada, and the two developed a line for export under the name Hana, the Japanese word 華, which the company translates as brilliant and gorgeous. The first four models were the EL and EH, with elliptical styli, and the SL and SH, with Shibata diamonds, each in a low-output version for moving-coil inputs and a high-output version for moving-magnet inputs. Herb Reichert reviewed the EL in Stereophile in August 2016, and The Absolute Sound covered all four in March 2017 at $475 and $750. Musical Surroundings of Oakland, California, became the US distributor.

The SL Mono of 2018 added a mono cartridge at $750. In October 2018 the M Series introduced the ideas that define the current range: a nude Microline stylus, a Delrin body with a brass cap, cryogenic treatment of the magnetic circuit, and an 8-ohm generator wound with thicker copper. hi-fi+ named the ML its Phono Cartridge of the Year for 2019. The Umami Red followed, announced on August 3, 2020 and on sale from September 22 at $3,950, with a boron cantilever, a samarium-cobalt magnet, a Duralumin body, an ebony inlay and red Urushi; its name, the fifth taste, was suggested by Garth Leerer of Musical Surroundings. It was hi-fi+'s Cartridge of the Year for 2020 and Stereophile Class A. The Umami Blue of March 2023, at $2,500, put the Red's body and cantilever over the ML's Alnico generator and won a Golden Ear from The Absolute Sound.

In September 2024 the S Series became the SL MK II, SH MK II and SL Mono MK II at $850, with a tapered aluminum cantilever, the 8-ohm generator, cryogenic treatment and the M-Series body; the original SL was cut to $600 and built for about six more months. The Umami Black, announced September 3, 2025 at $11,500, brought a diamond cantilever, a neodymium magnet and the OKD generator named for Okada, and that October an Umami Fest in Healdsburg, California gathered the brand's partners from six countries, with Okada present. The SH MK II won hi-fi+'s 2026 cartridge award, and on September 1, 2026 the E Series MK II, at $550, replaced the original entry models. Okada remains owner and president and designs every Hana; two of his craftsmen have been at Excel Sound for thirty to forty years. Pearl Audio carries the range in Portland.

The complete Hana story and technology library

Hana at Pearl Audio

Pearl Audio is an authorized Hana dealer in Portland, carrying the range from the entry E Series through the S Series MK II, SL Mono MK II and M Series to the Umami Blue, Red and Black. Because every series below the Umami comes in a low-output and a high-output winding, we start with the phono stage and tonearm you own and recommend the model that suits them, whether that is an MH into a moving-magnet input or an SL MK II at 80 ohms into a moving-coil stage. We install and align the cartridge in your arm, set tracking force and loading, and can advise on the step up from one series to the next when the time comes.

Ownership

Rebuilds, exchange and trade-in

Trade in a worn MH or ML and a new one is 30% off ($840). Trade in any other Hana, Clearaudio or DS Audio cartridge and it is 20% off ($960); any other brand's cartridge earns 10% off ($1,080).

Hana trade-in and re-tip exchange (Musical Surroundings)

Trade-in credit
—
Your price after trade-in
$1,200

Credit is 20% of the new cartridge’s price for a worn MH or ML at 30%; any Hana, Clearaudio or DS Audio cartridge at 20%; any other brand at 10%. The 30% re-tip exchange is Hana's replacement for retipping: a worn cartridge of the same series (working or not) is exchanged for a new one. Trade-ins of Musical Surroundings brands (Hana, Clearaudio, DS Audio) need an RA number and must arrive within 30 days of the invoice; other brands need an emailed photograph first. The Umami Blue and Red take other-brand trades only when the trade is worth more than $1,000 retail. Verified 2026-10-28.

Ask us about this trade-in

Factory rebuild and retip

ServicePrice
Hana re-tip exchange — MH or ML for a new MLHana does not retip; your worn cartridge is exchanged for a new one at 30% off $840

Pricing per Hana - 2026-01 - Dealer Price List (Musical Surroundings, January 2026) and musicalsurroundings.com/faq. Programs are set by the manufacturer and may change.

The Pearl Audio experience

How we work with you

A system at this level should be heard, thoughtfully matched, and properly set up. From the first audition to long-term ownership, you work with the same people, in person.

  1. 01

    Listen first

    The Hana ML is not in our rooms at present. When it is the right piece for a client we arrange a demonstration unit from the manufacturer and set it up for a private session.

  2. 02

    Delivery and installation

    We deliver and install throughout the Portland area, taking care of placement, connections, ventilation and system configuration ourselves.

  3. 03

    Support for as long as you own it

    We support everything we sell for as long as you own it, whether the answer comes by phone, in your home, or through factory service.

  4. 04

    A path for what comes next

    Trade-in assistance and qualifying 100% Trade-Up options give you flexibility when your listening priorities or your system change.

Search