← Back to your LP12 build

T+A Elektroakustik · Solitaire

T+A Elektroakustik Solitaire P

$8,995

Signature technologies

Not currently in our rooms. For a serious buyer we will often bring a piece in from the manufacturer for a private session — tell us about your system and what you are weighing it against, and we will advise.

T+A Elektroakustik · Solitaire

The Solitaire P is T+A's flagship headphone: an open planar-magnetostatic design built around the in-house TPM 3100 transducer, with cups machined from solid aluminum in Herford, Germany.

Price is for one pair with a 6.3 mm cable plus your choice of 4-pin XLR or 4.4 mm Pentaconn balanced cable.

110 × 80 mm
elliptical planar-magnetostatic driver
80 Ω
impedance
5 Hz – 54 kHz
frequency response
530 g
without cable

Authorized T+A Elektroakustik dealer · Delivery and installation by Pearl Audio · Trade-ins welcome

The story

T+A's first headphone draws on a transducer the company built in 1983: the planar-electrostatic midrange of its Solitaire OEC loudspeaker. The TPM 3100 driver is a film a few micrometers thick carrying conductors of similar thickness, applied photochemically, so the drive force acts across the whole diaphragm rather than at a voice coil. Rod-shaped neodymium magnets with a specific pole geometry create a linear field without opposing magnet arrays, which keeps the weight down and, T+A says, keeps distortion below 0.015 % at 100 dB.

The construction is open, so the diaphragm is not working into a closed cavity, and the cups are machined on a five-axis mill from 35 mm aluminum plate. The pads and headband are allergen-free synthetic leather and Alcantara. Two 3 m cables are supplied, one unbalanced 6.3 mm and one balanced, either four-pin XLR or 4.4 mm Pentaconn, in symmetrical construction with silver-plated OFC conductors and a silver-plated shield; the headphone-side connectors are gold-plated two-pole military-grade types.

At 80 Ω with a maximum output over 130 dB, the Solitaire P wants a capable amplifier. T+A designed the HA 200 for it. We can arrange a listening session in our Portland showroom.

The Solitaire name goes back to the Solitaire OEC of 1984 and 1985, a fully active loudspeaker with patented opto-electronic sensors, electrostatic drivers and direct-coupled high-voltage tube amplifiers. In March 2020 the Solitaire P headphones and the HA 200 opened a new category for T+A, around the TPM 3100 transducer developed and hand-made in Herford; Conradin Amft, who built the headphone range, became CEO of the family company in 2025. Read the T+A story →

Key technologies

  • TPM 3100 transducer. In-house planar-magnetostatic driver, 110 × 80 mm elliptical, built in Herford.
  • Homogeneous magnet field. Shaped neodymium magnets give a linear field with no supplementary opposed magnets.
  • Open construction. Avoids closed-cavity resonances and lets the diaphragm move freely.
  • Machined aluminum cups. Five-axis milled from 35 mm solid plate.
  • Symmetrical silver-plated cable. OFC conductors with a silver layer and a silver-plated woven shield, 3 m, two cables supplied.

The HA 200 is the amplifier T+A designed for the Solitaire P; the Solitaire P-SE is the lighter, 45 Ω step below.

Finishes

  • Aluminum silver (43) headband and pads black, allergen-free synthetic leather
Specifications
Type Open, over-ear planar-magnetostatic headphone
Transducer T+A TPM 3100, elliptical 110 × 80 mm
Impedance 80 Ω
Frequency response 5 Hz – 54 kHz
Distortion < 0.015 % at 100 dB
Maximum sound pressure > 130 dB
Sensitivity Not published by T+A
Cables 3 m unbalanced 6.3 mm plus 3 m balanced 4-pin XLR or 4.4 mm Pentaconn; gold-plated contacts
Materials Aluminum, steel, allergen-free synthetic leather, Alcantara
Weight 530 g (18.7 oz) without cable
Sold as One pair

T+A Solitaire P product page and specifications

Where it sits in the range

T+A's headphone products, least to most expensive:

Optional closed (EP SP HP) and semi-open (EP SP UW) ear pads are available for the Solitaire P.

Plan your T+A system with Pearl Audio

Pearl Audio is an authorized T+A dealer. We can arrange a listening session with the HA 200 in our Portland showroom. Call (503) 222-2599 or email sales@pearlaudio.com.

Signature technologies

The engineering behind the T+A Elektroakustik Solitaire P

T+A Elektroakustik gives its technologies names because each one solves a specific problem. Here is what each does, where it came from, why it matters in a system, and what you may hear.

A driver designed, machined and assembled in HerfordSince 2020

TPM planar-magnetostatic headphone transducers

The Solitaire P headphones are built around T+A's own TPM 3100 transducer, an elliptical 110 by 80 mm planar driver with an ultra-thin, ultra-light film carrying a computed conductor pattern, driven from one side only by shaped neodymium magnets. The Solitaire P-SE uses the TPM 2500 derivative; both are developed and hand-made in Herford. Read the deep diveClose

What it does

T+A entered headphones in March 2020 with the Solitaire P and the HA 200 amplifier, and chose to build the transducer rather than buy one. The TPM 3100 diaphragm is a special ultra-thin film whose conductor pattern is computed to match the magnet geometry; the magnets sit on one side only, so there is no second magnet array between the diaphragm and the ear to reflect and diffract the sound. The Solitaire P is an open design with an impedance of 80 ohms, a response from 5 Hz to 54 kHz, distortion below 0.015 percent at 100 dB and a maximum level above 130 dB; its cups are machined from a 35 mm aluminum plate on a five-axis mill, and it weighs 530 g. The Solitaire P-SE of 2021 carries the TPM 2500, a derivative of the same transducer, at 45 ohms, 8 Hz to 45 kHz and 440 g, with high-damping plastic cups. The closed, wireless Solitaire T of 2022 takes a different route: a 42 mm dynamic driver with a cellulose diaphragm, Bluetooth 5.1, hybrid noise cancelling, about 70 hours of battery and a passive wired mode. The HA 200 was designed as the amplifier for all of them: pure class A with MOS-FET transistors, no op-amps, selectable output impedance and analog crossfeed.

Why it matters in a system

A planar driver's weakness is usually the magnet array in front of it; a single-sided motor removes it, and a transducer made in-house can be matched to its amplifier. With the HA 200's selectable output impedance and class-A current to 700 mA, the headphones and the amplifier were designed as one system rather than as two products.

What you may hear

Herb Reichert, in Stereophile's Gramophone Dreams: materials, finish, and workmanship exceeded anything he had encountered, and the Solitaire P is definitely in the best-of-the-best headphone game. On the Solitaire T, Stereophile found the build quality outstanding.

Theory and application under one roofSince 1978

Designed, built and measured in Herford

Every T+A component is designed, assembled and measured at the company's own buildings in Herford, where it has been since 1988: circuit design, board layout, software, the MusicNavigator app, final assembly and a measurement protocol for every unit. Surface-mount board assembly is placed with a specialist using T+A-supplied parts; about 95 percent of production is in-house. Read the deep diveClose

What it does

T+A has occupied its own buildings in Herford since 1988 and added an administration, sales and laboratory building in 2003. A factory visit in April 2025 counted about 90 employees, 14 of them in research and development; T+A itself describes a team of fifteen designers and developers plus seven service technicians. The scope kept in-house runs from design, PCB layout and certification to assembly, measurement, operating-system programming and app development; the one step placed outside is surface-mount component placement, done by a specialist assembler using components T+A supplies, after which the boards return for final assembly and test. There are no assembly lines or automated placement machines, and nothing leaves the works without a measurement protocol. The company's own description is that it builds acoustic treasures rather than mass products, and it reports returning more than 98 percent of devices of any age to working condition when they come back for service. The engineering continuity is long: Lothar Wiemann, who joined as a student and developed the first electronics in 1982, was chief developer for 39 years before handing over to Jörg Küpper. In the United States, T+A North America in St. Marys, Georgia has handled distribution since August 2021, with service through Pyramid Audio in Austin and Audio Design and Service in Burbank.

Why it matters in a system

A product made in one place by the people who designed it can be supported for as long as its owner wants to keep it, and T+A's factory upgrades, the ASA G3 streaming boards fitted to players from 2017, are the practical form of that. It is also why a T+A system sounds consistent from the Series 200 to the HV line: the same small team designed all of it.

What you may hear

Jim Austin, in Stereophile on the MP 3100 HV: more than any other component he had had in his system, it radiated attention to detail. Michael Manousselis, who imported the brand to North America: they don't leave things to luck or to chance.

The Pearl Audio experience

How we work with you

A system at this level should be heard, thoughtfully matched, and properly set up. From the first audition to long-term ownership, you work with the same people, in person.

  1. 01

    Listen first

    The Solitaire P is not in our rooms at present. When it is the right piece for a client we arrange a demonstration unit from the manufacturer and set it up for a private session.

  2. 02

    Delivery and installation

    We deliver and install throughout the Portland area, taking care of placement, connections, ventilation and system configuration ourselves.

  3. 03

    Support for as long as you own it

    We support everything we sell for as long as you own it, whether the answer comes by phone, in your home, or through factory service.

  4. 04

    A path for what comes next

    Trade-in assistance and qualifying 100% Trade-Up options give you flexibility when your listening priorities or your system change.

Search