Inside a Boulder 3050 mono amplifier

Boulder technology

The engineering behind Boulder

Boulder gives its technologies names because each one solves a specific problem. Here is what each does, where it came from, why it matters in a system, and what you may hear.

From the 990 to the 99H2Since 1984

The discrete gain stage

Instead of an off-the-shelf op-amp chip, Boulder builds each amplifying block from individual transistors and resistors, hand-assembles and calibrates it, pots it in a machined metal shell and plugs it in as a module. The family descends from Deane Jensen's JE-990 discrete op-amp of the studio world, which Jeff Nelson refined and has developed through four generations. Read the deep diveClose

What it does

Deane Jensen of Jensen Transformers was Jeff Nelson's mentor, and his 990 was the discrete operational amplifier of the professional console era: a gain block built from selected transistors rather than a chip, with far more current and headroom than an integrated circuit. Boulder's 500 of 1984 used two of them per channel with about 100 dB of feedback applied locally rather than around the whole amplifier, and every Boulder since has been built on a descendant: the 993 in the 2000 Series of 1995, the 99H, high-voltage, in the 3050 and 3060, the 99H2 that replaced the 993 in the 2100 Series amplifiers in 2013 as a surface-mount, fully discrete, high-current design on 32-volt rails, the 993S, twelve of them, in the 2110 preamplifier, the 993SD in the 3010, the 995S in the 2108 phono stage, and the 983 and 985 in the 1100 Series. Each is potted and housed in a machined shell for thermal stability and shielding, and each is calibrated by hand before it is fitted.

Why it matters in a system

The gain stage is where a Boulder's noise, linearity and drive are decided, and building it as a replaceable module means every product in a series shares the same character and can be serviced for decades. It is also why Boulder can claim measured performance that reviewers describe as the best they have seen.

What you may hear

John Atkinson called the 2110 the best-measuring preamplifier he had encountered; Jacob Heilbrunn called the 3010 a proverbial straight wire with gain.

Studio practice since the first amplifierSince 1984

Fully balanced, dual mono, XLR only

Every Boulder carries the music as a pair of mirror-image signals from input to output, which cancels the noise picked up along the way, and gives the left and right channels their own boards, or in the 2100 and 3000 Series their own chassis. There are no unbalanced connections anywhere in the line. Read the deep diveClose

What it does

Boulder came out of broadcast and recording, where balanced lines are the only kind, and Jeff Nelson has used fully balanced circuit design from the start. Each balanced input gets a high-impedance buffer stage matched for common-mode rejection; the circuits use bipolar transistors rather than FETs, for a simpler topology, better thermal behavior and ruggedness. The 1110 isolates its channels on dual-mono boards in one chassis; the 2110 and 3010 preamplifiers are four chassis, left audio, right audio, user interface and power supply, and the 2110 of 2013 was the first 2000-series preamplifier balanced from input to output. The power amplifiers are two-stage, fully balanced designs, and the 866 integrated and 812 DAC preamplifier take XLR analog inputs only. A cartridge is itself a balanced source, so the phono stages keep it balanced from the input.

Why it matters in a system

Balanced operation cancels the noise between boxes, doubles the signal swing and removes the ground loops that plague unbalanced systems; an all-Boulder chain is balanced from the phono input to the loudspeaker terminals. It asks for balanced sources, which we take into account when we build a system around a Boulder preamplifier.

What you may hear

The black backgrounds and stability that reviewers hear as neutrality. Michael Fremer called the 2150 about as tonally neutral a piece of electronics as he had heard, neither warm nor cool.

Transformer hum is not permittedSince 1995

Linear power supplies, potted and sealed

Boulder uses only linear supplies, never switch-mode: custom American-wound toroidal transformers, DC-filtered, potted in epoxy and sealed in welded steel or machined cases so they cannot hum, feeding banks of many small, fast filter capacitors. The 2160 holds 48 of them; the 3050 carries four transformers in a 100-pound assembly. Read the deep diveClose

What it does

A power amplifier is a power supply that is modulated by the music, and Boulder's supplies are built on that premise. The 2160's two toroids, one per channel, float in a nickel-plated steel tube that is magnetically shielded and mass-loaded, more than 30 kilograms of it; a DC-elimination circuit blocks up to three volts of DC on the mains, the cause of transformer hum, and 48 electrolytic capacitors feed the output stage, because many smaller capacitors respond faster than a few large ones. The 3050 and 3060 carry four and five transformers in machined, potted housings; the 2150 puts dual toroids in a welded steel enclosure; the 1162's transformers are DC-filtered in a welded case. At full output the 2160 draws 5,000 watts and the 3000 Series 6,000, which is why the 2160 and 1162 take a 32-amp inlet and the 3050 and 3060 are built for 240-volt mains only. The 2110, 3010 and 2108 take their power from a separate chassis with independent supplies for left, right, control and standby; the power amplifiers keep their transformers inside.

Why it matters in a system

Dynamics come from the supply's ability to deliver current instantly and quietly, and a potted, shielded transformer with DC blocking is why a Boulder is silent at idle and unshakable at full power. Everything Boulder can make in America it does, including the transformers.

What you may hear

Alan Sircom found the 2160 one of a select handful of top-end powerhouses that can sound tiny when required and vast when called for; Anthony Cordesman was convinced the 2150 could get the best out of any real-world loudspeaker.

Five CNC centers and no sheet metalSince 1998

Machined from solid, in Louisville

Boulder cuts its chassis, heat sinks, knobs and even its buttons from solid aluminum blocks on its own CNC machining centers in Louisville, Colorado. The heat sinks have no fins, because fins ring; the interlocking panels are tuned so they do not share resonances; and the 1100 Series faceplate carries the contour lines of Flagstaff Mountain. Read the deep diveClose

What it does

Boulder bought its first Haas machining center in 1998, when production moved from the farmhouse in Superior to Boulder's industrial area, and it now runs five. Parts are machined from 6061-T6 aluminum at spindle speeds up to 65,000 rpm and held to half a thousandth of an inch; the 2160's heat sink is cut from an 80-pound billet, has no fins, and is damped by mounting to panels of differing resonant frequencies, while its output transistors are held by a machined clamp bar rather than individual screws, its top cover is damped as a constrained layer and its feet are four-piece damped assemblies. There is no sheet metal anywhere. The 1100 Series front panel is machined with the topographical map of Flagstaff Mountain, the peak above the town of Boulder, and the finish throughout is bead-blasted and clear-anodized. Anodizing, transformer winding and bare circuit boards are the only things done outside; everything else, every board and every piece of metalwork, is made in the Louisville factory, which Boulder describes as the last audio manufacturer in North America to hold this degree of control over its own designs.

Why it matters in a system

A chassis that does not resonate adds nothing to the music, and a company that machines its own parts can design a heat sink or a bracket for the circuit rather than the circuit for the parts available. It is why Boulder components look and feel as they do, and why a thirty-year-old one still works.

What you may hear

Jerry Del Colliano's summary was that Boulder builds audio equipment like no other company; Fremer noted the absence of standalone heat-sink fins, which Boulder says can resonate.

Bought as an act of self-defenseSince 2009

Circuit boards built in-house

Boulder places and solders its own surface-mount components on its own pick-and-place line, and tracks every board by barcode, so it knows exactly which board is in every product it has built. Read the deep diveClose

What it does

Surface-mount construction, tiny components soldered directly to the board, gives shorter signal paths and more consistent circuits than hand-wired parts, but only if the assembly is done to a high standard. Boulder's first surface-mount designs were the 1000 Series of 1999, and in 2009 it installed its own surface-mount manufacturing system rather than depend on a contractor; Jeff Nelson said the machine was bought as an act of self-defense, to ensure quality. The 1110's boards are built entirely on that line, the 2160's gain stages and output boards are surface-mount, and the 1162 and 1163 of 2025 required nearly every board in the 1160 to change, which is why the older amplifiers could not be converted. Each board is barcoded and logged, so a unit's history can be traced years later.

Why it matters in a system

The circuit is only as good as the board it is built on, and a company that assembles its own boards controls the one variable most high-end makers outsource. It is of a piece with the in-house machining: Boulder makes what it can and checks the rest.

What you may hear

Consistency from unit to unit, and the measured performance that John Atkinson has repeatedly called superb on Boulder amplifiers.

Class A without the heatSince 1995

Sliding bias and Smart Current

Boulder has two ways of running an output stage in class A without the waste. Sliding bias, in the 2100 and 3000 Series, watches the signal and raises the bias ahead of a peak, letting it fall back over half a minute. Smart Current, introduced on the 1151 in 2024, watches the current the loudspeaker draws and keeps both halves of the output stage conducting through the zero crossing, so there is no crossover notch and no need to run hot at idle. Read the deep diveClose

What it does

Pure class A keeps every output transistor conducting all the time, which removes crossover distortion and wastes most of the power as heat. Boulder's sliding bias, in use since the 2000 Series of 1995, is an analog circuit that senses the incoming signal and raises the bias faster than the music rises, then lets it decay over about 28 seconds, so the 2150 and 2160 are rated pure class A to full output and still run relatively cool; the 3050 and 3060 work the same way. Smart Current is a different idea, developed by Jeff Nelson and published in a white paper in 2026: the output stage continuously monitors the current the loudspeaker is actually drawing and adjusts itself so that the parasitic capacitance of the output devices is charged and discharged through every zero crossing, which Boulder says reduces crossover distortion so far as to be inaudible and guarantees that the amplifier's character does not change with the loudspeaker. The 1151 monoblocks of 2024 were the proof of concept, the 1162 and 1163 followed in 2025, replacing the 1160 and 1161, and the 851 mono of 2026 brings it to the 800 Series. The 1151 idles at 60 watts. The 866 integrated and the 861 are class AB.

Why it matters in a system

Crossover distortion is the characteristic flaw of a solid-state amplifier, and it is worst at the low levels where music spends most of its time. Both Boulder schemes remove it; Smart Current does so with far less heat and electricity, which is why the 1100 Series amplifiers can sit in a cabinet that the 2100 Series could not.

What you may hear

Jason Victor Serinus found the 1151 anything but dry or sterile, with an inner warmth and freshness; Oh Hifi's reviewer of the 1162 wrote that it does not create beauty, it unveils it.

Continuously active, outside the signal pathSince 1984

Supervised protection and Boulder Link

A supervising microprocessor outside the signal path watches DC, current, temperature and the supplies in every Boulder amplifier; a fault mutes or shuts the amplifier down, and its status appears on a linked Boulder preamplifier's display. The original 500 of 1984 already muted on a short and retested three seconds later. Read the deep diveClose

What it does

Boulder's amplifiers are designed to survive what happens in a real system: a shorted cable, a DC fault from a source, a blocked vent. In the 2160 a microprocessor controls and monitors the protection and the turn-on and turn-off of linked amplifiers; current limiting mutes the output for three seconds and tries again, an input servo nulls DC, thermal protection acts at 95 degrees Celsius at the transistor case, and if the microprocessor itself fails the amplifier powers off. Boulder Link carries the status to the preamplifier's display, which reports AMP DC, AMP ERROR or AMP HOT, and sequences the system on and off; the 1100 Series adds an Ethernet-enabled supervisor and newly developed protection that shuts the output section down immediately on a fault; the 861 sequences with the 812 over the network. The 866's new protection allows more current at maximum output. None of it sits in the signal path.

Why it matters in a system

Protection that is in the signal path, a fuse or a relay, degrades the sound; protection outside it protects a large investment without a cost. For an owner it means a Boulder system turns on in the right order from one button and tells you what is wrong if anything is.

What you may hear

Fremer called the 2150's protection heroically designed and built; hi-fi+ noted the 2160's protection circuitry outside the signal path covering DC offset, clipping and thermal conditions.

Its own filter, and Ethernet before USBSince 1996

Boulder digital: the 866 and 812

Boulder has made converters since the 2020 D/A converter of 1996 and writes its own digital filter. The 866 integrated's digital version and the 812 DAC preamplifier run one differential DAC per channel through Boulder's DSP, upsample PCM to 352.8 kHz, and stream as Roon endpoints with UPnP and AirPlay, preferring a wired Ethernet feed to USB. Read the deep diveClose

What it does

The 2020 D/A converter of 1996 was Boulder's first digital product; the 1012 DAC preamplifier was Stereo Sound's Component of the Year in 2000, and the four-chassis 2120 of 2015, with ten 99S gain stages per channel and Boulder's Eigen-algorithm filter, was the reference. The current approach is in the 866 and 812: a single differential DAC chip per channel, uncommon in high-end audio, fed by Boulder's own DSP, which sends the chip the same data format whatever the file and does the filtering itself. The 812 of 2022 is a DAC, a balanced preamplifier with a 100 dB optically encoded volume control and a headphone amplifier with balanced, quarter-inch and Pentaconn outputs, with Ethernet, four USB host ports, USB-B, optical and coaxial inputs, and it can be set to fixed output as a plain DAC; its filter and converter topology come from the 866. Both are Roon Ready, with UPnP and AirPlay, and controlled from the Boulder Controller app, which shows a photograph of the source on the display. The 866 is sold as an all-analog amplifier or with the digital board, which can be added later.

Why it matters in a system

A streamer built into a Boulder preamplifier removes a box, a cable and a power supply from the chain, and Boulder's preference for Ethernet over USB is about noise: a wired network feed is galvanically simpler than a computer's USB port. The 812 with an 861 or an 1163 is the smallest complete Boulder system.

What you may hear

Stereophile found the 866 a one-stop integrated made to uplift, not fatigue; Future Audiophile wrote that the 812 does far more than a comparable analog preamplifier for a little less money.

Balanced from the cartridge, with four curvesSince 2002

Phono stages and Personality Cards

A phono cartridge is a balanced source, and Boulder's phono stages keep it balanced all the way through. Gain and loading are set by small plug-in Personality Cards at the rear panel rather than by switches in the signal path, and four equalization curves, RIAA, EMI, FFRR and Columbia, let records cut before 1955 play as intended. Read the deep diveClose

What it does

The 2008 of 2002 earned Stereophile's A+ rating and a waiting list, and its descendants are the 2108 and 1108. The 2108, released in 2019 after three years of concept work, is fully balanced from input to output on the 995S gain stage, with three balanced inputs, each with its own Personality Card setting moving-magnet or moving-coil operation, loading, gain and a demagnetizing pass-through, 70 dB of moving-coil gain, a three-position low-cut filter and the separate 2100 Power Supply with four independent supplies. The 1108 puts the 985 gain stage in a machined aluminum block, with two balanced inputs, Personality Cards, the four curves and logic control instead of a microprocessor so that nothing digital runs near the highest-gain stage in the system; its equivalent input noise is 98 nanovolts. The 808 of 2026 brings the Personality Card system to the 800 Series.

Why it matters in a system

A phono stage amplifies the smallest signal in the system by a factor of thousands, so its noise and its grounding matter more than anywhere else; balanced input and cards outside the path are how Boulder keeps the stage quiet. The curves matter to anyone with early mono records, and we set the cards up for your cartridge on our bench.

What you may hear

Fremer found the 2108 produced both soaring exultation in the upper registers and gritty drama in the lowest, and told Boulder's detractors to give it a listen; Atkinson measured its RIAA response as almost perfect.

A sound room on its own foundationSince 2016

Every unit listened to before it ships

Every Boulder is played in one of the factory's three listening rooms before it leaves Louisville. The main room is isolated from the factory on its own foundation, with an ambient noise level measured at 28.5 dB, and the standard applied is the one Jeff Nelson brought from the studio: your gear will never be used again if it destroys a recording. Read the deep diveClose

What it does

Boulder bought three acres in Louisville, Colorado in 2015 and moved into its 23,000-square-foot factory on August 1, 2016, more than twice the size of the previous building. Besides the machining centers and the board line it holds three listening spaces, the largest built on a separate foundation so that the factory floor cannot be heard in it. Every finished unit is auditioned there, and the company offers tours by appointment. Nelson's background in broadcast and recording, where producers valued neutral, transparent performance, set the house standard: Boulder tries to design neutral rather than voiced, on the principle that every recording should sound different because every recording is different. The company has been independently owned since 1984, with Nelson as president and chief designer.

Why it matters in a system

A product that has been listened to is a product whose sound is known, and Boulder's test is the recording rather than a house flavor. It is why the brand is the choice of listeners who want the loudspeaker and the recording to be what they hear.

What you may hear

Rich Maez's description of the goal: neutral instead of voiced or flavored. Reviewers who expected analytical cool have, from the 2108 to the 1151, reported warmth and freshness instead.

Search