← Back to your LP12 build

T+A Elektroakustik · Solitaire

T+A Elektroakustik Solitaire P-SE

$5,490

Signature technologies

Not currently in our rooms. For a serious buyer we will often bring a piece in from the manufacturer for a private session — tell us about your system and what you are weighing it against, and we will advise.

T+A Elektroakustik · Solitaire

The Solitaire P-SE brings T+A's planar-magnetostatic driver to a lighter, easier-to-drive headphone: the TPM 2500 transducer, 45 Ω, 440 g, with two cables supplied.

Price is for one pair with a 6.3 mm cable plus your choice of 4-pin XLR or 4.4 mm Pentaconn balanced cable.

110 × 80 mm
elliptical planar-magnetostatic driver
45 Ω
impedance
8 Hz – 45 kHz
frequency response
440 g
without cable

Authorized T+A Elektroakustik dealer · Delivery and installation by Pearl Audio · Trade-ins welcome

The story

The Solitaire P-SE uses the same principle as the Solitaire P, a thin, ultra-light diaphragm carrying a photochemically applied conductor array, driven by neodymium magnets shaped to match the oval diaphragm so the field stays homogeneous. The TPM 2500 transducer is a new version of that driver tuned for a 45 Ω impedance, which makes the P-SE a practical match for more amplifiers, including good portable ones, while keeping distortion below 0.015 % at 100 dB and a maximum output above 130 dB.

T+A trimmed weight by using a thermoplastic shell with steel in place of the P's machined aluminum, finished in lacquers developed for aviation. The ear cushions and headband, in allergen-free synthetic leather and velour, are made by hand in Germany, and the sub-assemblies are machined to tolerances in hundredths of a millimeter. Two 3 m cables are standard: unbalanced 6.3 mm and balanced 4.4 mm Pentaconn, with a four-pin XLR lead available in place of the Pentaconn.

The P-SE is the Solitaire for someone who wants the open, planar character at a lower price and lower weight, with an amplifier like the HA 200 or a strong portable. We can arrange a listening session in our Portland showroom.

T+A's first headphones, the Solitaire P, arrived in March 2020 with the HA 200 amplifier, and the Solitaire P-SE followed in 2021 and won an EISA Award. Both are built around planar transducers developed and hand-made in Herford, where the company has been since Siegfried Amft founded it in 1978, and the headphone range was built up by his son Conradin, CEO since 2025. Read the T+A story →

Key technologies

  • TPM 2500 transducer. In-house planar-magnetostatic driver, 110 × 80 mm, tuned for 45 Ω.
  • No opposed magnets. Shaped neodymium magnets keep the field linear and the weight down.
  • Open construction. The diaphragm works without a closed cavity behind or in front of it.
  • Lightweight shell. Thermoplastic and steel with aviation-grade lacquer; 440 g.
  • Symmetrical cable. Four silver-plated OFC conductors with a silver-plated shield; two 3 m cables supplied.

The Solitaire P is the step up; the HA 200 is the amplifier built for both.

Finishes

  • Black synthetic compound; headband and pads black, allergen-free synthetic leather
Specifications
Type Open, over-ear planar-magnetostatic headphone
Transducer T+A TPM 2500, elliptical 110 × 80 mm
Impedance 45 Ω
Frequency response 8 Hz – 45 kHz
Distortion < 0.015 % at 100 dB
Maximum sound pressure > 130 dB
Sensitivity Not published by T+A
Cables 3 m unbalanced 6.3 mm plus 3 m balanced 4.4 mm Pentaconn (4-pin XLR optional in its place)
Materials Thermoplastic, steel, allergen-free synthetic leather, velour
Weight 440 g (15.5 oz) without cable
Sold as One pair

T+A Solitaire P-SE product page and specifications

Where it sits in the range

T+A's headphone products, least to most expensive:

Replacement ear pads (EP SP-SE) and shorter 1.2 m cables are available for the P-SE.

Plan your T+A system with Pearl Audio

Pearl Audio is an authorized T+A dealer. We can arrange a listening session with the HA 200 in our Portland showroom. Call (503) 222-2599 or email sales@pearlaudio.com.

Signature technologies

The engineering behind the T+A Elektroakustik Solitaire P-SE

T+A Elektroakustik gives its technologies names because each one solves a specific problem. Here is what each does, where it came from, why it matters in a system, and what you may hear.

A driver designed, machined and assembled in HerfordSince 2020

TPM planar-magnetostatic headphone transducers

The Solitaire P headphones are built around T+A's own TPM 3100 transducer, an elliptical 110 by 80 mm planar driver with an ultra-thin, ultra-light film carrying a computed conductor pattern, driven from one side only by shaped neodymium magnets. The Solitaire P-SE uses the TPM 2500 derivative; both are developed and hand-made in Herford. Read the deep diveClose

What it does

T+A entered headphones in March 2020 with the Solitaire P and the HA 200 amplifier, and chose to build the transducer rather than buy one. The TPM 3100 diaphragm is a special ultra-thin film whose conductor pattern is computed to match the magnet geometry; the magnets sit on one side only, so there is no second magnet array between the diaphragm and the ear to reflect and diffract the sound. The Solitaire P is an open design with an impedance of 80 ohms, a response from 5 Hz to 54 kHz, distortion below 0.015 percent at 100 dB and a maximum level above 130 dB; its cups are machined from a 35 mm aluminum plate on a five-axis mill, and it weighs 530 g. The Solitaire P-SE of 2021 carries the TPM 2500, a derivative of the same transducer, at 45 ohms, 8 Hz to 45 kHz and 440 g, with high-damping plastic cups. The closed, wireless Solitaire T of 2022 takes a different route: a 42 mm dynamic driver with a cellulose diaphragm, Bluetooth 5.1, hybrid noise cancelling, about 70 hours of battery and a passive wired mode. The HA 200 was designed as the amplifier for all of them: pure class A with MOS-FET transistors, no op-amps, selectable output impedance and analog crossfeed.

Why it matters in a system

A planar driver's weakness is usually the magnet array in front of it; a single-sided motor removes it, and a transducer made in-house can be matched to its amplifier. With the HA 200's selectable output impedance and class-A current to 700 mA, the headphones and the amplifier were designed as one system rather than as two products.

What you may hear

Herb Reichert, in Stereophile's Gramophone Dreams: materials, finish, and workmanship exceeded anything he had encountered, and the Solitaire P is definitely in the best-of-the-best headphone game. On the Solitaire T, Stereophile found the build quality outstanding.

Theory and application under one roofSince 1978

Designed, built and measured in Herford

Every T+A component is designed, assembled and measured at the company's own buildings in Herford, where it has been since 1988: circuit design, board layout, software, the MusicNavigator app, final assembly and a measurement protocol for every unit. Surface-mount board assembly is placed with a specialist using T+A-supplied parts; about 95 percent of production is in-house. Read the deep diveClose

What it does

T+A has occupied its own buildings in Herford since 1988 and added an administration, sales and laboratory building in 2003. A factory visit in April 2025 counted about 90 employees, 14 of them in research and development; T+A itself describes a team of fifteen designers and developers plus seven service technicians. The scope kept in-house runs from design, PCB layout and certification to assembly, measurement, operating-system programming and app development; the one step placed outside is surface-mount component placement, done by a specialist assembler using components T+A supplies, after which the boards return for final assembly and test. There are no assembly lines or automated placement machines, and nothing leaves the works without a measurement protocol. The company's own description is that it builds acoustic treasures rather than mass products, and it reports returning more than 98 percent of devices of any age to working condition when they come back for service. The engineering continuity is long: Lothar Wiemann, who joined as a student and developed the first electronics in 1982, was chief developer for 39 years before handing over to Jörg Küpper. In the United States, T+A North America in St. Marys, Georgia has handled distribution since August 2021, with service through Pyramid Audio in Austin and Audio Design and Service in Burbank.

Why it matters in a system

A product made in one place by the people who designed it can be supported for as long as its owner wants to keep it, and T+A's factory upgrades, the ASA G3 streaming boards fitted to players from 2017, are the practical form of that. It is also why a T+A system sounds consistent from the Series 200 to the HV line: the same small team designed all of it.

What you may hear

Jim Austin, in Stereophile on the MP 3100 HV: more than any other component he had had in his system, it radiated attention to detail. Michael Manousselis, who imported the brand to North America: they don't leave things to luck or to chance.

The Pearl Audio experience

How we work with you

A system at this level should be heard, thoughtfully matched, and properly set up. From the first audition to long-term ownership, you work with the same people, in person.

  1. 01

    Listen first

    The Solitaire P-SE is not in our rooms at present. When it is the right piece for a client we arrange a demonstration unit from the manufacturer and set it up for a private session.

  2. 02

    Delivery and installation

    We deliver and install throughout the Portland area, taking care of placement, connections, ventilation and system configuration ourselves.

  3. 03

    Support for as long as you own it

    We support everything we sell for as long as you own it, whether the answer comes by phone, in your home, or through factory service.

  4. 04

    A path for what comes next

    Trade-in assistance and qualifying 100% Trade-Up options give you flexibility when your listening priorities or your system change.

Search