← Back to your LP12 build

T+A Elektroakustik · R-Series

T+A Elektroakustik T+A PA 2000 R Integrated Amplifier

$11,990

Signature technologies

Not currently in our rooms. For a serious buyer we will often bring a piece in from the manufacturer for a private session — tell us about your system and what you are weighing it against, and we will advise.

T+A Elektroakustik · R-Series

The PA 2000 R puts T+A's HV-Series thinking into a low-profile case: a double mono integrated amplifier with a J-FET input stage, relay volume control and 100 W into 8 Ω.

Includes the SRC 1 remote. T+A's November 2026 US price list refers to this model as the PA 2000 R SL.

100 W
per channel into 8 Ω (200 W into 4 Ω)
8.2 cm
chassis height
105 / 109 dB
signal-to-noise, unweighted / A-weighted
10.5 kg
23 lb
Options and pricing

Authorized T+A Elektroakustik dealer · Delivery and installation by Pearl Audio · Trade-ins welcome

The story

The PA 2000 R is the amplifier T+A designed when it wanted HV-Series circuit ideas in an R-Series case. Left and right channels sit on identical boards and are isolated from each other, mechanically as well as electrically. The input stage is a cascoded differential amplifier using hand-selected audio J-FETs, with no op-amps anywhere, and T+A says it can pass signals of 60 V peak-to-peak without distortion. The output stages are linear designs with very low negative feedback.

Power comes from a mains supply T+A developed specifically for audio: a regulated high-frequency sine-wave unit that holds its voltage under load so the amplifier does not sag on peaks. Sealed, gas-tight gold-contact relays do the volume control and the input and speaker switching. There are three RCA and three XLR inputs, a headphone socket and an RCA pre-out; an optional phono board, MM or MC, takes the place of one line input.

At 8.2 cm tall it pairs visually with the MP 2000 R G3 and the G 2000 R turntable, and R2-Link lets the SRC 1 remote run all three. It is the right R-Series amplifier for most rooms and most loudspeakers of average sensitivity; the PA 2500 R adds headroom for harder loads. We can arrange an audition in our Portland showroom and help with system matching, delivery and setup.

T+A's first stand-alone preamplifiers and power amplifiers appeared under the Pulsar name in 1986, and by 1992 electronics earned the company more than loudspeakers; the Pulsar electronics evolved into the R series that year. The PA 2000 R arrived in 2015 with the G 2000 R turntable, carrying the circuit ideas of the High Voltage series of 2013 into the R series case, and it is built in Herford, where T+A has designed and measured every unit since 1978. Read the T+A story →

Key technologies

  • Double mono layout. Identical, isolated left and right boards in one chassis.
  • J-FET input stage. Cascoded differential amplifier with hand-selected audio J-FETs and no op-amps.
  • Sine-wave power supply. A regulated high-frequency supply designed for audio, with 60,000 µF of reservoir capacitance.
  • Gold-contact relays. Sealed relays for volume, input and loudspeaker switching.
  • Optional phono. Plug-in MM or MC module with 16 capacitance or impedance settings.

The MP 2000 R G3 is the PA 2000 R's matching source; the PA 2500 R is the step up within the R series.

Finishes

  • Silver anodized (43) brushed aluminum
  • Black anodized (42) brushed aluminum
Specifications
Type Stereo integrated amplifier, Class AB
Power output 100 W into 8 Ω, 200 W into 4 Ω, 300 W into 2 Ω (per channel)
Frequency response 1 Hz – 150 kHz (+0/–3 dB); preamplifier 0.5 Hz – 300 kHz
Distortion < 0.02 % (output stage); < 0.001 % (preamplifier)
Signal-to-noise 105 dB unweighted, 109 dB A-weighted
Damping factor > 65
Inputs 3 × RCA, 3 × XLR; optional phono MM or MC replaces one line input
Outputs Loudspeakers, headphone (50 Ω), pre-out RCA
Remote SRC 1 included; R2-Link control bus
Power consumption Max. 1,000 W; standby < 0.5 W
Dimensions (H × W × D) 8.2 × 46 × 40 cm (3.2 × 18.1 × 15.7 in)
Weight 10.5 kg (23.1 lb)
Finishes Silver anodized (43) or black anodized (42)

T+A PA 2000 R product page and specifications

Where it sits in the range

The R-Series is T+A's full-size line below the HV-Series. Siblings, least to most expensive:

The MP 2000 R G3 is the matching source; both are 8.2 cm tall and share the SRC 1 remote.

Plan your T+A system with Pearl Audio

Pearl Audio is an authorized T+A dealer. We can arrange an audition in our Portland showroom and help with system matching, delivery and setup. Call (503) 222-2599 or email sales@pearlaudio.com.

Signature technologies

The engineering behind the T+A Elektroakustik T+A PA 2000 R Integrated Amplifier

T+A Elektroakustik gives its technologies names because each one solves a specific problem. Here is what each does, where it came from, why it matters in a system, and what you may hear.

Transistors run where they are most linearSince 2013

HV: high-voltage amplifier stages

T+A's HV circuits run their transistor voltage-gain stages on supply rails several times higher than ordinary solid-state designs, up to 100 V in the P 3100 HV preamplifier and up to 500 V in the M 40 HV's power stages. Each device then works over a small, linear part of its curve, as a tube does, so the circuit needs virtually no overall negative feedback. Read the deep diveClose

What it does

Most solid-state audio circuits run on low rails; Alan Sircom notes that most modern circuits run at about plus and minus 5 V. The High Voltage series, three years in development and introduced in 2012 by Siegfried Amft's account or 2013 by T+A's own, moved the voltage-gain stages to rails several times higher, with the stated aim of combining the sonic and technical advantages of tubes and transistors while avoiding the inherent disadvantages of present-day valves. In the PA 3100 HV the input is a differential cascode amplifier of individually selected audio J-FET transistors that can process signals up to 60 V peak-to-peak without distortion; the P 3100 HV runs at up to 100 V and handles 80 V peak-to-peak; the M 40 HV's power stages reach 500 V, behind a class-A input stage of 6SN7 triodes. Because each transistor works over a small, linear part of its curve, the circuit needs virtually no overall negative feedback, and bandwidth and headroom are wide: the P 3100 HV is specified from 0.5 Hz to 300 kHz. HV is used in the amplifier stages of every HV-series component, the same voltage-gain stage appears in the Series 200, the HA 200 and the Symphonia, and the PA 2500 R and PA 2000 R carry a high-voltage dual-mono design on the R-series chassis.

Why it matters in a system

An amplifier stage that stays linear without heavy feedback behaves the same from the first watt to clipping and into awkward loudspeaker loads, which is what HV owners describe as ease at volume. It is also the reason a T+A preamplifier, converter and power amplifier sound of a piece: the same voltage-gain stage sits in all of them, from the DAC 200 to the M 40 HV.

What you may hear

Jason Victor Serinus, reviewing the PA 3100 HV for Stereophile, found the midrange strong, exceptionally smooth, and all of one piece. Alan Sircom in hi-fi+ called the SDV 3100 HV extremely listenable, with extraordinary clarity and dynamics, and musically inviting.

No potentiometer, no chip, no coupling capacitorsSince 2020

Relay volume control and the DC-coupled preamplifier

T+A sets volume by switching precision resistors with encapsulated, gas-tight gold-contact relays rather than with a potentiometer or a volume chip, in 1 dB steps on the DAC 200. In the 3100-generation preamplifiers the coupling capacitors between the input stage, the volume control and the output were removed by a board layout that compensates the transistors' temperature drift. Read the deep diveClose

What it does

A volume control is in series with everything, and the usual choices, a carbon or conductive-plastic potentiometer or an integrated-circuit attenuator, each add noise, channel imbalance or a sound of their own. T+A's HV preamplifiers and the DAC 200 instead use a ladder of precision resistors selected by sealed relays with gold contacts, so at every setting the signal passes through fixed resistors and closed metal contacts. The P 3100 HV of May 2020 went a step further. Lothar Wiemann's goal for the 3100 generation was a capacitor-free preamplifier without servo control, in pursuit of what he called black level: more quiet, fewer disturbances, a blacker background. A new and complex board layout compensates for the transistors' temperature coefficients, so the stages from input to output are DC-coupled with no coupling capacitors and remain, in T+A's words, completely voltage and temperature stable. The PA 3100 HV shares the DC-coupled preamplifier section, which along with its VU meters and a redesigned mains section distinguishes it from the PA 3000 HV; the PSD 3100 HV and SDX 3100 HV carry the same class-A discrete HV preamplifier with relay volume; and the PA 2000 R and PA 2500 R use relay volume on the R-series chassis.

Why it matters in a system

A preamplifier's job is to lose nothing, and capacitors and potentiometers are where most of the loss happens: at low volume, where most listening is done, and in the lowest octaves, which coupling capacitors roll off. Relay switching and DC coupling are why the HV preamplifiers are described in terms of silence between the notes rather than any tonal character.

What you may hear

Matthew Clott, reviewing the PSD 3100 HV for The Absolute Sound: it's not a component you evaluate; it's a component you listen to, and highly, highly recommended. Jason Victor Serinus found the PA 3100 HV meticulously engineered and beautifully made.

Theory and application under one roofSince 1978

Designed, built and measured in Herford

Every T+A component is designed, assembled and measured at the company's own buildings in Herford, where it has been since 1988: circuit design, board layout, software, the MusicNavigator app, final assembly and a measurement protocol for every unit. Surface-mount board assembly is placed with a specialist using T+A-supplied parts; about 95 percent of production is in-house. Read the deep diveClose

What it does

T+A has occupied its own buildings in Herford since 1988 and added an administration, sales and laboratory building in 2003. A factory visit in April 2025 counted about 90 employees, 14 of them in research and development; T+A itself describes a team of fifteen designers and developers plus seven service technicians. The scope kept in-house runs from design, PCB layout and certification to assembly, measurement, operating-system programming and app development; the one step placed outside is surface-mount component placement, done by a specialist assembler using components T+A supplies, after which the boards return for final assembly and test. There are no assembly lines or automated placement machines, and nothing leaves the works without a measurement protocol. The company's own description is that it builds acoustic treasures rather than mass products, and it reports returning more than 98 percent of devices of any age to working condition when they come back for service. The engineering continuity is long: Lothar Wiemann, who joined as a student and developed the first electronics in 1982, was chief developer for 39 years before handing over to Jörg Küpper. In the United States, T+A North America in St. Marys, Georgia has handled distribution since August 2021, with service through Pyramid Audio in Austin and Audio Design and Service in Burbank.

Why it matters in a system

A product made in one place by the people who designed it can be supported for as long as its owner wants to keep it, and T+A's factory upgrades, the ASA G3 streaming boards fitted to players from 2017, are the practical form of that. It is also why a T+A system sounds consistent from the Series 200 to the HV line: the same small team designed all of it.

What you may hear

Jim Austin, in Stereophile on the MP 3100 HV: more than any other component he had had in his system, it radiated attention to detail. Michael Manousselis, who imported the brand to North America: they don't leave things to luck or to chance.

The Pearl Audio experience

How we work with you

A system at this level should be heard, thoughtfully matched, and properly set up. From the first audition to long-term ownership, you work with the same people, in person.

  1. 01

    Listen first

    The T+A PA 2000 R Integrated Amplifier is not in our rooms at present. When it is the right piece for a client we arrange a demonstration unit from the manufacturer and set it up for a private session.

  2. 02

    Delivery and installation

    We deliver and install throughout the Portland area, taking care of placement, connections, ventilation and system configuration ourselves.

  3. 03

    Support for as long as you own it

    We support everything we sell for as long as you own it, whether the answer comes by phone, in your home, or through factory service.

  4. 04

    A path for what comes next

    Trade-in assistance and qualifying 100% Trade-Up options give you flexibility when your listening priorities or your system change.

Search