← Back to your LP12 build

T+A Elektroakustik · Series 200

T+A Elektroakustik T+A DAC 200 DAC / Preamplifier

$9,495

Signature technologies

Not currently in our rooms. For a serious buyer we will often bring a piece in from the manufacturer for a private session — tell us about your system and what you are weighing it against, and we will advise.

T+A Elektroakustik · Series 200

The DAC 200 is T+A's compact converter-preamplifier: eight 32-bit DACs for PCM to 768 kHz, a True 1-Bit converter for DSD to DSD1024, relay volume control and a Class A Pentaconn headphone output in a 32 cm case.

Includes the FM200 remote. HDMI board is optional.

768 kHz
PCM
DSD1024
native, 49.2 MHz
110 / 114 dB
signal-to-noise
6.2 kg
13.7 lb
Options and pricing

Authorized T+A Elektroakustik dealer · Advice and support from Pearl Audio · Trade-ins welcome

How it sounds

Fast, open and dynamic, from a fully discrete design with separate signal paths for PCM and DSD and a true analog volume control.

The Absolute Sound Editors' Choice Award 2027.

The story

The DAC 200 brings the HV-Series converter architecture down to a 32 cm chassis without simplifying it. PCM is handled by a double-differential quadruple converter, four 32-bit sigma-delta DACs per channel, running at up to 705.6 or 768 kHz; DSD goes to T+A's True 1-Bit converter as a native bitstream, up to DSD1024 over USB. A de-jitter master clock cleans and re-clocks whatever arrives, and six upsampling and filter options, including Bezier and NOS modes, sit in front of a third-order Bessel analog filter switchable between 60 and 120 kHz.

It is also a preamplifier. Volume is set in 1 dB steps by gold-contact relays, the RCA and XLR outputs can be fixed or variable, and there is an analog RCA input. The headphone stage is a discrete Class A design on a 4.4 mm Pentaconn socket with 6 Ω output impedance and up to 200 mA of current. Inputs include AES/EBU, two coaxial, two optical, BNC and two USB; an optional board adds two HDMI inputs and an ARC output. T+A's DASS system keeps the digital and analog sections, and their power supplies, galvanically isolated.

With the A 200 stereo amplifier or a pair of M 200 monoblocks and the MP 200 G3 as a source, the DAC 200 anchors a complete Series 200 system that fits on a desk or a shelf. We can arrange an audition in our Portland showroom and help with system matching, delivery and setup.

T+A announced the Series 200, the DAC 200, A 200 and MP 200, on September 17, 2021, a month after setting up T+A North America in St. Marys, Georgia. The DAC 200 inherited the converter design of the SDV 3100 HV of 2019, with the separate PCM and DSD paths T+A has built since the DAC 8 DSD of 2015, and it is designed, built and measured in Herford. Read the T+A story →

Key technologies

  • Path Separation. Quadruple 32-bit converter for PCM; True 1-Bit converter for DSD to DSD1024.
  • De-jitter master clock. Incoming clocks are analyzed, cleaned and replaced by precision local oscillators.
  • DASS. Digital isolators and separate galvanically isolated mains supplies for digital and analog.
  • Relay volume control. Gold-contact relays in 1 dB steps from –90 to 0 dB; fixed or variable outputs.
  • Class A headphone stage. Discrete output on 4.4 mm Pentaconn, 6 Ω, up to 200 mA.
  • Six filter options. Bezier and NOS upsampling modes plus a switchable 60/120 kHz Bessel analog filter.

The A 200 is the DAC 200's matching amplifier; the MP 200 G3 is its matching source.

Finishes

  • Alu silver anodized (43)
  • Alu black anodized (42)
Specifications
Type D/A converter and preamplifier
PCM conversion Double-differential quadruple converter, four 32-bit DACs per channel, 705.6/768 kHz
DSD T+A True 1-Bit converter, native bitstream up to DSD1024 (49.2 MHz) via USB
Frequency response 0.1 Hz – 200 kHz (+0/–3 dB)
Signal-to-noise 110 dB unweighted, 114 dB A-weighted; distortion < 0.001 %
Digital inputs 1 × AES/EBU, 2 × coaxial, 2 × optical, 1 × BNC, 2 × USB DAC (768 kHz / DSD1024)
HDMI Optional module: 2 × HDMI in, 1 × HDMI out with ARC
Analog input RCA 250 mV – 4.5 V / 10 kΩ
Analog outputs RCA 2.5 V and XLR 5.0 V, fixed or variable, 22 Ω
Headphone output 4.4 mm Pentaconn, Class A, 6 Ω, up to 200 mA
Volume control Gold-contact relays, 1 dB steps, –90 to 0 dB
Remote FM200 included; USB cable supplied
Dimensions (H × W × D) 10 × 32 × 34 cm (3.9 × 12.6 × 13.4 in)
Weight 6.2 kg (13.7 lb)
Finishes Alu silver anodized (43) or alu black anodized (42)

T+A DAC 200 product page and specifications

Where it sits in the range

Series 200 is T+A's compact line. Siblings, least to most expensive:

  • T+A M 200: 210 W into 8 Ω mono amplifier, price each
  • T+A A 200: 125 W into 8 Ω stereo amplifier
  • T+A MP 200 G3: CD, streaming and tuner source
  • T+A DAC 200 (this model)
  • T+A HA 200: headphone amplifier and DAC

The HA 200 shares the converter and adds a full headphone amplifier; the DAC 200 is the choice when loudspeakers come first.

Reviews

Plan your T+A system with Pearl Audio

Pearl Audio is an authorized T+A dealer. We can arrange an audition in our Portland showroom and help with system matching, delivery and setup. Call (503) 222-2599 or email sales@pearlaudio.com.

Signature technologies

The engineering behind the T+A Elektroakustik T+A DAC 200 DAC / Preamplifier

T+A Elektroakustik gives its technologies names because each one solves a specific problem. Here is what each does, where it came from, why it matters in a system, and what you may hear.

Transistors run where they are most linearSince 2013

HV: high-voltage amplifier stages

T+A's HV circuits run their transistor voltage-gain stages on supply rails several times higher than ordinary solid-state designs, up to 100 V in the P 3100 HV preamplifier and up to 500 V in the M 40 HV's power stages. Each device then works over a small, linear part of its curve, as a tube does, so the circuit needs virtually no overall negative feedback. Read the deep diveClose

What it does

Most solid-state audio circuits run on low rails; Alan Sircom notes that most modern circuits run at about plus and minus 5 V. The High Voltage series, three years in development and introduced in 2012 by Siegfried Amft's account or 2013 by T+A's own, moved the voltage-gain stages to rails several times higher, with the stated aim of combining the sonic and technical advantages of tubes and transistors while avoiding the inherent disadvantages of present-day valves. In the PA 3100 HV the input is a differential cascode amplifier of individually selected audio J-FET transistors that can process signals up to 60 V peak-to-peak without distortion; the P 3100 HV runs at up to 100 V and handles 80 V peak-to-peak; the M 40 HV's power stages reach 500 V, behind a class-A input stage of 6SN7 triodes. Because each transistor works over a small, linear part of its curve, the circuit needs virtually no overall negative feedback, and bandwidth and headroom are wide: the P 3100 HV is specified from 0.5 Hz to 300 kHz. HV is used in the amplifier stages of every HV-series component, the same voltage-gain stage appears in the Series 200, the HA 200 and the Symphonia, and the PA 2500 R and PA 2000 R carry a high-voltage dual-mono design on the R-series chassis.

Why it matters in a system

An amplifier stage that stays linear without heavy feedback behaves the same from the first watt to clipping and into awkward loudspeaker loads, which is what HV owners describe as ease at volume. It is also the reason a T+A preamplifier, converter and power amplifier sound of a piece: the same voltage-gain stage sits in all of them, from the DAC 200 to the M 40 HV.

What you may hear

Jason Victor Serinus, reviewing the PA 3100 HV for Stereophile, found the midrange strong, exceptionally smooth, and all of one piece. Alan Sircom in hi-fi+ called the SDV 3100 HV extremely listenable, with extraordinary clarity and dynamics, and musically inviting.

PCM and DSD never meetSince 2015

Two converters: Quadruple PCM and True 1-bit DSD

Instead of converting DSD to PCM inside one chip, every current T+A converter carries two. PCM goes to eight 32-bit Burr-Brown sigma-delta chips, four per channel in a double-differential arrangement; DSD goes to a discrete one-bit converter of T+A's own design that never touches PCM, and relays switch between the two paths. Read the deep diveClose

What it does

T+A's converter layout dates from the DAC 8 DSD of about 2015, when Lothar Wiemann concluded that it was very difficult to preserve a true DSD signal path with ready-made chips. The PCM side is the Double-Differential-Quadruple-Converter: four 32-bit Burr-Brown sigma-delta converters per channel, run in conversion-only mode with T+A's own upsampling and filtering ahead of them, an arrangement T+A says lowers noise by 6 dB. The MP 3100 HV G3 feeds them at 352.8 or 384 kHz; the DAC 200 and PSD 3100 HV accept PCM to 768 kHz. The DSD side is the T+A True-1Bit converter, a discrete circuit that takes the native bitstream and oversamples it; T+A holds that DSD's advantages appear only when the signal is massively oversampled, and the reference converter upsamples DSD by 32 times. The DAC 200, HA 200 and SDX 3100 HV decode up to DSD 1024, or 49.2 MHz, a capability T+A introduced in the SD and SDV 3100 HV of March 2019 and calls the world's first DSD 1024-capable player; the PSD 3100 HV, MP 3100 HV G3, MP 2500 R G3, R 2500 R and Symphonia are specified to DSD 512. In 2026 T+A gave the arrangement a name, Path Separation Technology. The Symphonia uses a two-chip-per-channel Double Differential derivative of the PCM converter.

Why it matters in a system

A chip that handles DSD by first turning it into PCM, or the reverse, imposes one filter's character on both formats. Giving each its own converter means an SACD or a DSD file reaches the analog stage as the bitstream it was recorded as, and a PCM file is handled by a converter built for multi-bit data with T+A's own filters in front of it.

What you may hear

Herb Reichert, reviewing the MP 3100 HV G3 for Stereophile, wrote that the T+A's smooth, nuanced sigma-delta feels considerably different than dCS's liquidy FPGA-controlled Ring DAC, and called it CD playback at its highest imaginable level. Jim Austin heard treble that glistened, with no digital glare.

Four filters, no ringing, the listener's choiceSince 2015

Bézier oversampling filters and 56-bit DSP

T+A writes its own PCM oversampling in a signal processor instead of using the filters built into the converter chips: two FIR filters and two Bézier-polynomial filters, plus a non-oversampling mode, selectable by the owner. The Bézier filters avoid the pre- and post-ringing of conventional filters, and a third-order Bessel analog filter follows, switchable between 60 and 120 kHz. Read the deep diveClose

What it does

Every oversampling converter interpolates new samples between the ones on the disc or in the file, and the filter that does it leaves a signature; conventional linear-phase FIR filters ring before and after each transient. In the DAC 8 DSD T+A moved this work out of the converter chip and into a 56-bit signal processor running its own algorithms, and the current units offer five settings: FIR short, FIR long, Bézier/IIR, Bézier and NOS, or non-oversampling. Lothar Wiemann's point about the Bézier interpolation is that it has no pre-ringing and no post-ringing. In the reference converters a 16-times Bézier-polynomial filter takes 44.1 and 88.2 kHz material to 705.6 kHz and 48, 96 and 192 kHz material to 768 kHz before the Quadruple converter sees it. After conversion a phase-linear third-order Bessel filter, switchable between a 60 and a 120 kHz cut-off, removes what remains above the audio band without adding ringing of its own. The same processor and filter set run in the DAC 200 and HA 200, the MP 2000 R G3 and MP 2500 R G3, the R 2500 R, the PSD 3100 HV, the MP 3100 HV G3 and the SDX 3100 HV, so the choice an owner makes on a Series 200 converter is the same one offered on the reference.

Why it matters in a system

The reconstruction filter determines how a converter handles the leading edge of every note, and the ringing of a steep filter is one reason digital playback can sound hard. Letting the listener choose among FIR, Bézier and no oversampling, with an analog filter gentle enough to add nothing of its own, means the converter can be matched to the recording and to the rest of the system.

What you may hear

Jim Austin, in Stereophile on the MP 3100 HV: treble tones glisten like light reflected from the facets of a diamond, and also seem especially relaxed, with no digital glare. Craig Joyce at StereoNET called the DAC 200 a standout product that handles a wide range of music with clarity and precision.

Two mains inlets, isolated data, one clockSince 2020

Digital-analog separation and the De-Jitter Masterclock

In T+A's converters the digital and analog sections have their own power supplies and, in the HV components, their own IEC mains inlets; data crossing between them passes through ultra-fast digital isolators, so switching noise cannot reach the analog output. Incoming digital signals are reclocked in two stages against a quartz master clock before they reach the converter. Read the deep diveClose

What it does

A converter's analog output is only as quiet as the ground it shares with its digital logic. T+A's answer, which it calls the Digital Analogue Separation System in the DAC 200, is to keep the two halves apart electrically: the analog and digital mains sections are galvanically separated, each with its own transformer, and the signal and control lines between them run through ultra-fast digital isolators from Silicon Labs, with the clocks isolated as well. The HV components go further and fit two IEC inlets, so the MP 3100 HV G3 draws its digital and analog power through separate cords, and the P 3100 HV, a purely analog preamplifier, gives each channel its own inlet. The timing side is the De-Jitter Masterclock: an incoming signal first passes a phase-locked loop, then a microprocessor checks it and switches to a quartz master clock; when the signal fails T+A's criteria a second stage, the Second Jitterbug, engages and cuts residual jitter by a factor of four. The SDX 3100 HV uses two femto-second crystal oscillators feeding a multi-stage jitter-cleansing system. James Shannon of T+A says the separate AC inputs make it virtually impossible to see any kind of digital noise entering the analog output.

Why it matters in a system

Noise that leaks from a streaming board or a USB receiver into the analog stage does not sound like hiss; it sounds like a loss of depth and a hardening of the treble that is easy to blame on the recording. Isolation and reclocking are what let a T+A converter accept a laptop or a network stream and sound as quiet as it does from its own disc drive.

What you may hear

Stereophile on the R 2500 R: its DAC is in keeping with the very best modern DACs in that it is ultra-revealing and transparent, and the component doesn't call attention to itself in any way. Craig Joyce at StereoNET gave the DAC 200 a 9 out of 10 and an Applause Award.

No potentiometer, no chip, no coupling capacitorsSince 2020

Relay volume control and the DC-coupled preamplifier

T+A sets volume by switching precision resistors with encapsulated, gas-tight gold-contact relays rather than with a potentiometer or a volume chip, in 1 dB steps on the DAC 200. In the 3100-generation preamplifiers the coupling capacitors between the input stage, the volume control and the output were removed by a board layout that compensates the transistors' temperature drift. Read the deep diveClose

What it does

A volume control is in series with everything, and the usual choices, a carbon or conductive-plastic potentiometer or an integrated-circuit attenuator, each add noise, channel imbalance or a sound of their own. T+A's HV preamplifiers and the DAC 200 instead use a ladder of precision resistors selected by sealed relays with gold contacts, so at every setting the signal passes through fixed resistors and closed metal contacts. The P 3100 HV of May 2020 went a step further. Lothar Wiemann's goal for the 3100 generation was a capacitor-free preamplifier without servo control, in pursuit of what he called black level: more quiet, fewer disturbances, a blacker background. A new and complex board layout compensates for the transistors' temperature coefficients, so the stages from input to output are DC-coupled with no coupling capacitors and remain, in T+A's words, completely voltage and temperature stable. The PA 3100 HV shares the DC-coupled preamplifier section, which along with its VU meters and a redesigned mains section distinguishes it from the PA 3000 HV; the PSD 3100 HV and SDX 3100 HV carry the same class-A discrete HV preamplifier with relay volume; and the PA 2000 R and PA 2500 R use relay volume on the R-series chassis.

Why it matters in a system

A preamplifier's job is to lose nothing, and capacitors and potentiometers are where most of the loss happens: at low volume, where most listening is done, and in the lowest octaves, which coupling capacitors roll off. Relay switching and DC coupling are why the HV preamplifiers are described in terms of silence between the notes rather than any tonal character.

What you may hear

Matthew Clott, reviewing the PSD 3100 HV for The Absolute Sound: it's not a component you evaluate; it's a component you listen to, and highly, highly recommended. Jason Victor Serinus found the PA 3100 HV meticulously engineered and beautifully made.

Theory and application under one roofSince 1978

Designed, built and measured in Herford

Every T+A component is designed, assembled and measured at the company's own buildings in Herford, where it has been since 1988: circuit design, board layout, software, the MusicNavigator app, final assembly and a measurement protocol for every unit. Surface-mount board assembly is placed with a specialist using T+A-supplied parts; about 95 percent of production is in-house. Read the deep diveClose

What it does

T+A has occupied its own buildings in Herford since 1988 and added an administration, sales and laboratory building in 2003. A factory visit in April 2025 counted about 90 employees, 14 of them in research and development; T+A itself describes a team of fifteen designers and developers plus seven service technicians. The scope kept in-house runs from design, PCB layout and certification to assembly, measurement, operating-system programming and app development; the one step placed outside is surface-mount component placement, done by a specialist assembler using components T+A supplies, after which the boards return for final assembly and test. There are no assembly lines or automated placement machines, and nothing leaves the works without a measurement protocol. The company's own description is that it builds acoustic treasures rather than mass products, and it reports returning more than 98 percent of devices of any age to working condition when they come back for service. The engineering continuity is long: Lothar Wiemann, who joined as a student and developed the first electronics in 1982, was chief developer for 39 years before handing over to Jörg Küpper. In the United States, T+A North America in St. Marys, Georgia has handled distribution since August 2021, with service through Pyramid Audio in Austin and Audio Design and Service in Burbank.

Why it matters in a system

A product made in one place by the people who designed it can be supported for as long as its owner wants to keep it, and T+A's factory upgrades, the ASA G3 streaming boards fitted to players from 2017, are the practical form of that. It is also why a T+A system sounds consistent from the Series 200 to the HV line: the same small team designed all of it.

What you may hear

Jim Austin, in Stereophile on the MP 3100 HV: more than any other component he had had in his system, it radiated attention to detail. Michael Manousselis, who imported the brand to North America: they don't leave things to luck or to chance.

The Pearl Audio experience

How we work with you

A system at this level should be heard, thoughtfully matched, and properly set up. From the first audition to long-term ownership, you work with the same people, in person.

  1. 01

    Listen first

    The T+A DAC 200 DAC / Preamplifier is not in our rooms at present. When it is the right piece for a client we arrange a demonstration unit from the manufacturer and set it up for a private session.

  2. 02

    Placement and setup advice

    Ask us about placement, connections, ventilation and system configuration, and about delivery.

  3. 03

    Support for as long as you own it

    We support everything we sell for as long as you own it, whether the answer comes by phone, in the shop, or through factory service.

  4. 04

    A path for what comes next

    Trade-in assistance and qualifying 100% Trade-Up options give you flexibility when your listening priorities or your system change.

Search