← Back to your LP12 build

T+A Elektroakustik · HV-Series

T+A Elektroakustik T+A P 3100 HV Preamplifier

$26,490

Signature technologies

Not currently in our rooms. For a serious buyer we will often bring a piece in from the manufacturer for a private session — tell us about your system and what you are weighing it against, and we will advise.

T+A Elektroakustik · HV-Series

The P 3100 HV is T+A's reference analog preamplifier: a discrete, DC-coupled, double mono design running on rails of up to 100 V, with no op-amps and no coupling capacitors in the signal path.

Supplied with the F 3001 remote. HV-Series units are built to order in silver or titanium lacquer.

100 V
operating voltage
108 / 112 dB
signal-to-noise, unweighted / A-weighted
7 + 4
RCA and XLR inputs
28 kg
61.7 lb

Authorized T+A Elektroakustik dealer · Advice and support from Pearl Audio · Trade-ins welcome

The story

The idea behind T+A's HV-Series is simple to state: run the audio circuits at very high voltage, so the signal only ever uses a small fraction of each transistor's range. In the P 3100 HV that means supply rails of up to 100 V, with the signal using less than a fifth of the available swing, where the devices are at their most linear. Linearity comes from the topology, a differential cascode built from hand-selected J-FETs, rather than from heavy negative feedback, and T+A says it will pass 80 V peak-to-peak without distortion.

The signal path is pure DC: input stage, volume control and output stage are directly coupled with no capacitors between them. The two channels are built on identical boards in aluminum compartments with 10 to 15 mm walls, isolated from the power supply, which has a 115 VA toroidal transformer for the analog section and a separately shielded supply for control. Seven RCA and four XLR inputs, a high-current headphone output and both RCA and XLR pre-outs cover any system; a slot takes an optional MM/MC phono module.

The P 3100 HV is the preamplifier for the A 3100 HV stereo amplifier or the M 40 HV monoblocks, and it sits visually with the MP 3100 HV G3 and PDT 3100 HV. We can arrange an audition in our Portland showroom and help with system matching, delivery and setup.

T+A's High Voltage series took three years to develop and reached the market in 2013, when the MP 3000 HV and PA 3000 HV won the EISA High-End Audio award; the idea was to run transistor gain stages at supply voltages several times higher than usual, so each device works over a small, linear part of its curve as a tube does. The P 3100 HV followed on May 21, 2020 as the series' DC-coupled reference preamplifier, designed and built like every T+A in Herford, where the company Siegfried Amft founded in 1978 still works. Read the T+A story →

Key technologies

  • HV technology. Supply rails up to 100 V so the signal uses under 20 % of the transistors' excursion.
  • Pure DC coupling. No coupling capacitors between input stage, volume control and output.
  • Discrete double mono. Identical channel boards in thick-walled aluminum compartments, no op-amps.
  • J-FET cascode. Differential cascode input stage with hand-selected audio J-FETs.
  • Enlarged power supply. 115 VA analog toroidal transformer and a shielded, separate digital supply.

The M 40 HV monoblocks are the P 3100 HV's partners; the PSD 3100 HV is the preamplifier with the converter and streaming built in.

Finishes

  • Silver lacquer (47) case; heat sinks black (42)
  • Titanium lacquer (64) case; heat sinks black (42)

HV-Series units ship in heavy-duty flight cases.

Specifications
Type Stereo line preamplifier, fully discrete
Frequency response 0.5 Hz – 300 kHz (+0/–3 dB)
Signal-to-noise 108 dB unweighted, 112 dB A-weighted
Distortion < 0.001 %; channel separation > 108 dB
Inputs 7 × RCA (250 mV – 9 V / 20 kΩ), 4 × XLR (500 mV – 18 V / 5 kΩ); slot for optional MM/MC phono module
Outputs Pre-out RCA (max. 9.5 V / 50 Ω) and XLR (max. 19.6 V / 50 Ω), recorder output, headphone (50 Ω, high current)
Reservoir capacity 75,000 µF
Remote F 3001 included; E 2000 receiver and two power cords supplied
Power consumption 10 W + 60 W rated; standby < 0.5 W
Dimensions (H × W × D) 17 × 46 × 46 cm (6.7 × 18.1 × 18.1 in)
Weight 28 kg (61.7 lb)
Finishes Silver lacquer (47) or titanium lacquer (64); heat sinks black (42)

T+A P 3100 HV product page and specifications

Where it sits in the range

The HV-Series is T+A's reference line. Siblings, least to most expensive:

The PSD 3100 HV combines a preamplifier of this class with a streamer and DAC if you do not need the analog inputs.

Plan your T+A system with Pearl Audio

Pearl Audio is an authorized T+A dealer. We can arrange an audition in our Portland showroom and help with system matching, delivery and setup. Call (503) 222-2599 or email sales@pearlaudio.com.

Signature technologies

The engineering behind the T+A Elektroakustik T+A P 3100 HV Preamplifier

T+A Elektroakustik gives its technologies names because each one solves a specific problem. Here is what each does, where it came from, why it matters in a system, and what you may hear.

Transistors run where they are most linearSince 2013

HV: high-voltage amplifier stages

T+A's HV circuits run their transistor voltage-gain stages on supply rails several times higher than ordinary solid-state designs, up to 100 V in the P 3100 HV preamplifier and up to 500 V in the M 40 HV's power stages. Each device then works over a small, linear part of its curve, as a tube does, so the circuit needs virtually no overall negative feedback. Read the deep diveClose

What it does

Most solid-state audio circuits run on low rails; Alan Sircom notes that most modern circuits run at about plus and minus 5 V. The High Voltage series, three years in development and introduced in 2012 by Siegfried Amft's account or 2013 by T+A's own, moved the voltage-gain stages to rails several times higher, with the stated aim of combining the sonic and technical advantages of tubes and transistors while avoiding the inherent disadvantages of present-day valves. In the PA 3100 HV the input is a differential cascode amplifier of individually selected audio J-FET transistors that can process signals up to 60 V peak-to-peak without distortion; the P 3100 HV runs at up to 100 V and handles 80 V peak-to-peak; the M 40 HV's power stages reach 500 V, behind a class-A input stage of 6SN7 triodes. Because each transistor works over a small, linear part of its curve, the circuit needs virtually no overall negative feedback, and bandwidth and headroom are wide: the P 3100 HV is specified from 0.5 Hz to 300 kHz. HV is used in the amplifier stages of every HV-series component, the same voltage-gain stage appears in the Series 200, the HA 200 and the Symphonia, and the PA 2500 R and PA 2000 R carry a high-voltage dual-mono design on the R-series chassis.

Why it matters in a system

An amplifier stage that stays linear without heavy feedback behaves the same from the first watt to clipping and into awkward loudspeaker loads, which is what HV owners describe as ease at volume. It is also the reason a T+A preamplifier, converter and power amplifier sound of a piece: the same voltage-gain stage sits in all of them, from the DAC 200 to the M 40 HV.

What you may hear

Jason Victor Serinus, reviewing the PA 3100 HV for Stereophile, found the midrange strong, exceptionally smooth, and all of one piece. Alan Sircom in hi-fi+ called the SDV 3100 HV extremely listenable, with extraordinary clarity and dynamics, and musically inviting.

Two mains inlets, isolated data, one clockSince 2020

Digital-analog separation and the De-Jitter Masterclock

In T+A's converters the digital and analog sections have their own power supplies and, in the HV components, their own IEC mains inlets; data crossing between them passes through ultra-fast digital isolators, so switching noise cannot reach the analog output. Incoming digital signals are reclocked in two stages against a quartz master clock before they reach the converter. Read the deep diveClose

What it does

A converter's analog output is only as quiet as the ground it shares with its digital logic. T+A's answer, which it calls the Digital Analogue Separation System in the DAC 200, is to keep the two halves apart electrically: the analog and digital mains sections are galvanically separated, each with its own transformer, and the signal and control lines between them run through ultra-fast digital isolators from Silicon Labs, with the clocks isolated as well. The HV components go further and fit two IEC inlets, so the MP 3100 HV G3 draws its digital and analog power through separate cords, and the P 3100 HV, a purely analog preamplifier, gives each channel its own inlet. The timing side is the De-Jitter Masterclock: an incoming signal first passes a phase-locked loop, then a microprocessor checks it and switches to a quartz master clock; when the signal fails T+A's criteria a second stage, the Second Jitterbug, engages and cuts residual jitter by a factor of four. The SDX 3100 HV uses two femto-second crystal oscillators feeding a multi-stage jitter-cleansing system. James Shannon of T+A says the separate AC inputs make it virtually impossible to see any kind of digital noise entering the analog output.

Why it matters in a system

Noise that leaks from a streaming board or a USB receiver into the analog stage does not sound like hiss; it sounds like a loss of depth and a hardening of the treble that is easy to blame on the recording. Isolation and reclocking are what let a T+A converter accept a laptop or a network stream and sound as quiet as it does from its own disc drive.

What you may hear

Stereophile on the R 2500 R: its DAC is in keeping with the very best modern DACs in that it is ultra-revealing and transparent, and the component doesn't call attention to itself in any way. Craig Joyce at StereoNET gave the DAC 200 a 9 out of 10 and an Applause Award.

No potentiometer, no chip, no coupling capacitorsSince 2020

Relay volume control and the DC-coupled preamplifier

T+A sets volume by switching precision resistors with encapsulated, gas-tight gold-contact relays rather than with a potentiometer or a volume chip, in 1 dB steps on the DAC 200. In the 3100-generation preamplifiers the coupling capacitors between the input stage, the volume control and the output were removed by a board layout that compensates the transistors' temperature drift. Read the deep diveClose

What it does

A volume control is in series with everything, and the usual choices, a carbon or conductive-plastic potentiometer or an integrated-circuit attenuator, each add noise, channel imbalance or a sound of their own. T+A's HV preamplifiers and the DAC 200 instead use a ladder of precision resistors selected by sealed relays with gold contacts, so at every setting the signal passes through fixed resistors and closed metal contacts. The P 3100 HV of May 2020 went a step further. Lothar Wiemann's goal for the 3100 generation was a capacitor-free preamplifier without servo control, in pursuit of what he called black level: more quiet, fewer disturbances, a blacker background. A new and complex board layout compensates for the transistors' temperature coefficients, so the stages from input to output are DC-coupled with no coupling capacitors and remain, in T+A's words, completely voltage and temperature stable. The PA 3100 HV shares the DC-coupled preamplifier section, which along with its VU meters and a redesigned mains section distinguishes it from the PA 3000 HV; the PSD 3100 HV and SDX 3100 HV carry the same class-A discrete HV preamplifier with relay volume; and the PA 2000 R and PA 2500 R use relay volume on the R-series chassis.

Why it matters in a system

A preamplifier's job is to lose nothing, and capacitors and potentiometers are where most of the loss happens: at low volume, where most listening is done, and in the lowest octaves, which coupling capacitors roll off. Relay switching and DC coupling are why the HV preamplifiers are described in terms of silence between the notes rather than any tonal character.

What you may hear

Matthew Clott, reviewing the PSD 3100 HV for The Absolute Sound: it's not a component you evaluate; it's a component you listen to, and highly, highly recommended. Jason Victor Serinus found the PA 3100 HV meticulously engineered and beautifully made.

Theory and application under one roofSince 1978

Designed, built and measured in Herford

Every T+A component is designed, assembled and measured at the company's own buildings in Herford, where it has been since 1988: circuit design, board layout, software, the MusicNavigator app, final assembly and a measurement protocol for every unit. Surface-mount board assembly is placed with a specialist using T+A-supplied parts; about 95 percent of production is in-house. Read the deep diveClose

What it does

T+A has occupied its own buildings in Herford since 1988 and added an administration, sales and laboratory building in 2003. A factory visit in April 2025 counted about 90 employees, 14 of them in research and development; T+A itself describes a team of fifteen designers and developers plus seven service technicians. The scope kept in-house runs from design, PCB layout and certification to assembly, measurement, operating-system programming and app development; the one step placed outside is surface-mount component placement, done by a specialist assembler using components T+A supplies, after which the boards return for final assembly and test. There are no assembly lines or automated placement machines, and nothing leaves the works without a measurement protocol. The company's own description is that it builds acoustic treasures rather than mass products, and it reports returning more than 98 percent of devices of any age to working condition when they come back for service. The engineering continuity is long: Lothar Wiemann, who joined as a student and developed the first electronics in 1982, was chief developer for 39 years before handing over to Jörg Küpper. In the United States, T+A North America in St. Marys, Georgia has handled distribution since August 2021, with service through Pyramid Audio in Austin and Audio Design and Service in Burbank.

Why it matters in a system

A product made in one place by the people who designed it can be supported for as long as its owner wants to keep it, and T+A's factory upgrades, the ASA G3 streaming boards fitted to players from 2017, are the practical form of that. It is also why a T+A system sounds consistent from the Series 200 to the HV line: the same small team designed all of it.

What you may hear

Jim Austin, in Stereophile on the MP 3100 HV: more than any other component he had had in his system, it radiated attention to detail. Michael Manousselis, who imported the brand to North America: they don't leave things to luck or to chance.

The Pearl Audio experience

How we work with you

A system at this level should be heard, thoughtfully matched, and properly set up. From the first audition to long-term ownership, you work with the same people, in person.

  1. 01

    Listen first

    The T+A P 3100 HV Preamplifier is not in our rooms at present. When it is the right piece for a client we arrange a demonstration unit from the manufacturer and set it up for a private session.

  2. 02

    Placement and setup advice

    Ask us about placement, connections, ventilation and system configuration, and about delivery.

  3. 03

    Support for as long as you own it

    We support everything we sell for as long as you own it, whether the answer comes by phone, in the shop, or through factory service.

  4. 04

    A path for what comes next

    Trade-in assistance and qualifying 100% Trade-Up options give you flexibility when your listening priorities or your system change.

Search