← Back to your LP12 build

T+A Elektroakustik · HV-Series

T+A Elektroakustik T+A PDT 3100 HV CD/SACD Transport

$25,490

Signature technologies

Not currently in our rooms. For a serious buyer we will often bring a piece in from the manufacturer for a private session — tell us about your system and what you are weighing it against, and we will advise.

T+A Elektroakustik · HV-Series

The PDT 3100 HV does one thing: it reads CD and SACD with T+A's own linear-tracking mechanism and hands the data to a DAC, over AES/EBU for CD or over the proprietary IPA link, which also carries SACD, to the SDX 3100 HV or PSD 3100 HV.

Transport only, no converter. Supplied with the F 3100 remote and IPA bus cable.

SACD + CD
dual-laser linear-tracking drive
29 kg
63.9 lb
1 × AES/EBU
plus IPA link for SACD data
40 W
power consumption

Authorized T+A Elektroakustik dealer · Delivery and installation by Pearl Audio · Trade-ins welcome

The story

The PDT 3100 HV is the purist's version of the MP 3100 HV G3. It contains the same in-house disc mechanism, a linear-tracking drive with a dual GaAlAs laser (650 nm for SACD, 785 nm for CD) riding on two linear bearings hung from a carrier plate fixed to the chassis at three points, inside a case machined from solid aluminum. There are no tuners, no streaming boards and no converters; everything in the 29 kg chassis exists to read the disc and get the data out cleanly.

CD data leaves on an AES/EBU output for any DAC. SACD's DSD stream, which the standard interfaces cannot carry, leaves over T+A's IPA link to a matching T+A converter: the SDX 3100 HV or the PSD 3100 HV, both of which have an IPA input and a True 1-Bit DSD converter. In that configuration the SACD layer is played natively from transport to analog output without a PCM conversion anywhere.

This is the transport for a system built around a PSD 3100 HV or SDX 3100 HV, where the converter is already the best T+A makes and the disc drive should match it. We can arrange an audition in our Portland showroom and help with system matching, delivery and setup.

On March 8, 2019 T+A announced the PDT 3100 HV together with the SD 3100 HV and SDV 3100 HV converters, with an SACD mechanism developed from the ground up in Herford and DSD processed to DSD 1024; The Absolute Sound named the SDV and the PDT its Products of the Year. The SDX 3100 HV replaced the SDV in July 2026, and the PDT 3100 HV remains the transport the IPA Link was built for. Read the T+A story →

Key technologies

  • In-house linear-tracking drive. Dual-laser mechanism on two linear bearings, suspended from a three-point carrier plate.
  • Solid aluminum housing. The mechanism sits in a machined enclosure that shields it and isolates it from the heavy outer chassis.
  • IPA link. T+A's proprietary interface carries SACD's DSD data to the SDX 3100 HV or PSD 3100 HV.
  • AES/EBU output. Standard 32 – 192 kHz output for CD playback into any DAC.

The PSD 3100 HV is the PDT 3100 HV's converter; the MP 3100 HV G3 is the same mechanism with the converter and streaming in one chassis.

Finishes

  • Silver lacquer (47) case; heat sinks black (42)
  • Titanium lacquer (64) case; heat sinks black (42)

HV-Series units ship in heavy-duty flight cases.

Specifications
Type CD/SACD transport (no converter)
Drive High-precision linear-tracking mechanism; dual GaAlAs laser, SACD 650 nm / CD 785 nm
Disc formats CD, CD-R, CD-RW, SACD stereo, SACD/CD Text
Frequency range CD 2 Hz – 20 kHz / 100 dB; SACD 2 Hz – 44 kHz / 110 dB
Digital outputs 1 × AES/EBU (32 – 192 kHz, 16 – 24 bit); IPA link for T+A converters (carries SACD data)
Remote F 3100 included
Power consumption 40 W; standby < 0.5 W
Dimensions (H × W × D) 17 × 46 × 46 cm (6.7 × 18.1 × 18.1 in)
Weight 29 kg (63.9 lb)
Finishes Silver lacquer (47) or titanium lacquer (64)

T+A PDT 3100 HV product page and specifications

Where it sits in the range

The HV-Series is T+A's reference line. Siblings, least to most expensive:

The MP 3100 HV G3 is the one-box alternative with converter, streaming and tuners built in.

Plan your T+A system with Pearl Audio

Pearl Audio is an authorized T+A dealer. We can arrange an audition in our Portland showroom and help with system matching, delivery and setup. Call (503) 222-2599 or email sales@pearlaudio.com.

Signature technologies

The engineering behind the T+A Elektroakustik T+A PDT 3100 HV CD/SACD Transport

T+A Elektroakustik gives its technologies names because each one solves a specific problem. Here is what each does, where it came from, why it matters in a system, and what you may hear.

PCM and DSD never meetSince 2015

Two converters: Quadruple PCM and True 1-bit DSD

Instead of converting DSD to PCM inside one chip, every current T+A converter carries two. PCM goes to eight 32-bit Burr-Brown sigma-delta chips, four per channel in a double-differential arrangement; DSD goes to a discrete one-bit converter of T+A's own design that never touches PCM, and relays switch between the two paths. Read the deep diveClose

What it does

T+A's converter layout dates from the DAC 8 DSD of about 2015, when Lothar Wiemann concluded that it was very difficult to preserve a true DSD signal path with ready-made chips. The PCM side is the Double-Differential-Quadruple-Converter: four 32-bit Burr-Brown sigma-delta converters per channel, run in conversion-only mode with T+A's own upsampling and filtering ahead of them, an arrangement T+A says lowers noise by 6 dB. The MP 3100 HV G3 feeds them at 352.8 or 384 kHz; the DAC 200 and PSD 3100 HV accept PCM to 768 kHz. The DSD side is the T+A True-1Bit converter, a discrete circuit that takes the native bitstream and oversamples it; T+A holds that DSD's advantages appear only when the signal is massively oversampled, and the reference converter upsamples DSD by 32 times. The DAC 200, HA 200 and SDX 3100 HV decode up to DSD 1024, or 49.2 MHz, a capability T+A introduced in the SD and SDV 3100 HV of March 2019 and calls the world's first DSD 1024-capable player; the PSD 3100 HV, MP 3100 HV G3, MP 2500 R G3, R 2500 R and Symphonia are specified to DSD 512. In 2026 T+A gave the arrangement a name, Path Separation Technology. The Symphonia uses a two-chip-per-channel Double Differential derivative of the PCM converter.

Why it matters in a system

A chip that handles DSD by first turning it into PCM, or the reverse, imposes one filter's character on both formats. Giving each its own converter means an SACD or a DSD file reaches the analog stage as the bitstream it was recorded as, and a PCM file is handled by a converter built for multi-bit data with T+A's own filters in front of it.

What you may hear

Herb Reichert, reviewing the MP 3100 HV G3 for Stereophile, wrote that the T+A's smooth, nuanced sigma-delta feels considerably different than dCS's liquidy FPGA-controlled Ring DAC, and called it CD playback at its highest imaginable level. Jim Austin heard treble that glistened, with no digital glare.

A disc mechanism machined in Herford, not bought inSince 2019

In-house SACD transport and IPA Link

T+A builds its own disc transport: a linear-tracking laser block riding on two aluminum linear bearings inside a chassis machined from a single block of aluminum, with its own servo board, SACD decoder and control software. DSD leaves the transport as the native bitstream, and the IPA Link carries it, with its clock, to the matching converter. Read the deep diveClose

What it does

Most SACD players use a drive and decoder chipset made for Blu-ray players, and convert the disc's DSD to PCM before it goes anywhere. For the PDT 3100 HV of March 2019 T+A's engineers developed a decoder and drive mechanism from the ground up: a high-precision linear-tracking drive with a double laser, 658 nm for SACD and 790 nm for CD, a high-torque synchronous motor, an anti-resonance weight, a chassis cut from one aluminum block, two aluminum linear bearings, and a drawer that runs on stainless steel rails in PTFE and phosphor-bronze bearings. The servo board, SACD decoder and control software are T+A's own, written to deliver native DSD and PCM rather than converting DSD to PCM first; James Shannon's argument is that less error correction means greater accuracy of the decoding process. The mechanism alone weighs nearly 20 pounds. The High Res IPA Link is a proprietary connection, using low-voltage differential signalling, that transmits PCM and DSD data bit-accurately along with high-precision clocking, a constant bitstream of unchanged raw data, from the PDT 3100 HV to the SD, SDV and SDX 3100 HV. The same drive sits inside the MP 3100 HV G3 and the MP 2500 R G3, while the MP 2000 R G3, MP 200 G3 and R 2500 R use a slot-loading CD drive.

Why it matters in a system

A transport is the one part of a digital system that is still mechanical, and read errors, vibration and the conversion of DSD to PCM all happen before the converter can do anything about them. Owning the mechanism and the decoder lets T+A keep SACD native, and keep the drive in production and in service for as long as the player.

What you may hear

Robert Harley, reviewing the PDT 3100 HV with the SDV 3100 HV for The Absolute Sound, called it by far the smoothest and quietest transport he had encountered, with SACD playback vaulted into another realm. Herb Reichert found the MP 3100 HV G3 CD playback at its highest imaginable level.

Theory and application under one roofSince 1978

Designed, built and measured in Herford

Every T+A component is designed, assembled and measured at the company's own buildings in Herford, where it has been since 1988: circuit design, board layout, software, the MusicNavigator app, final assembly and a measurement protocol for every unit. Surface-mount board assembly is placed with a specialist using T+A-supplied parts; about 95 percent of production is in-house. Read the deep diveClose

What it does

T+A has occupied its own buildings in Herford since 1988 and added an administration, sales and laboratory building in 2003. A factory visit in April 2025 counted about 90 employees, 14 of them in research and development; T+A itself describes a team of fifteen designers and developers plus seven service technicians. The scope kept in-house runs from design, PCB layout and certification to assembly, measurement, operating-system programming and app development; the one step placed outside is surface-mount component placement, done by a specialist assembler using components T+A supplies, after which the boards return for final assembly and test. There are no assembly lines or automated placement machines, and nothing leaves the works without a measurement protocol. The company's own description is that it builds acoustic treasures rather than mass products, and it reports returning more than 98 percent of devices of any age to working condition when they come back for service. The engineering continuity is long: Lothar Wiemann, who joined as a student and developed the first electronics in 1982, was chief developer for 39 years before handing over to Jörg Küpper. In the United States, T+A North America in St. Marys, Georgia has handled distribution since August 2021, with service through Pyramid Audio in Austin and Audio Design and Service in Burbank.

Why it matters in a system

A product made in one place by the people who designed it can be supported for as long as its owner wants to keep it, and T+A's factory upgrades, the ASA G3 streaming boards fitted to players from 2017, are the practical form of that. It is also why a T+A system sounds consistent from the Series 200 to the HV line: the same small team designed all of it.

What you may hear

Jim Austin, in Stereophile on the MP 3100 HV: more than any other component he had had in his system, it radiated attention to detail. Michael Manousselis, who imported the brand to North America: they don't leave things to luck or to chance.

The Pearl Audio experience

How we work with you

A system at this level should be heard, thoughtfully matched, and properly set up. From the first audition to long-term ownership, you work with the same people, in person.

  1. 01

    Listen first

    The T+A PDT 3100 HV CD/SACD Transport is not in our rooms at present. When it is the right piece for a client we arrange a demonstration unit from the manufacturer and set it up for a private session.

  2. 02

    Delivery and installation

    We deliver and install throughout the Portland area, taking care of placement, connections, ventilation and system configuration ourselves.

  3. 03

    Support for as long as you own it

    We support everything we sell for as long as you own it, whether the answer comes by phone, in your home, or through factory service.

  4. 04

    A path for what comes next

    Trade-in assistance and qualifying 100% Trade-Up options give you flexibility when your listening priorities or your system change.

Search