← Back to your LP12 build

T+A Elektroakustik · R-Series

T+A Elektroakustik T+A R 2500 R Streaming CD Receiver

$20,990

Signature technologies

Not currently in our rooms. For a serious buyer we will often bring a piece in from the manufacturer for a private session — tell us about your system and what you are weighing it against, and we will advise.

T+A Elektroakustik · R-Series

The R 2500 R is the whole R-Series in one box: a 140 W double mono amplifier, CD drive, streaming client, tuners, Bluetooth, HDMI ARC and T+A's full PCM/DSD converter, with the SRC 2 remote.

Includes the SRC 2 remote. Phono is an optional plug-in module.

140 W
per channel into 8 Ω (250 W into 4 Ω)
768 kHz
PCM; DSD512 native
2 + 1
HDMI inputs and ARC output
14 kg
30.8 lb

Authorized T+A Elektroakustik dealer · Delivery and installation by Pearl Audio · Trade-ins welcome

The story

T+A's R 2500 R is a receiver in the old, generous sense. The amplifier section is a discrete double mono design with separate left and right boards, a J-FET input stage without op-amps, little overall negative feedback and a high-frequency sine-wave power supply that recharges its reservoir capacitors tens of thousands of times a second. It delivers 140 W into 8 Ω and 250 W into 4 Ω, with a slew rate of 60 V/µs.

The source side is the MP 2500 R G3 platform minus SACD: a CD drive, third-generation streaming with Roon Ready, Tidal, Spotify and Qobuz Connect and AirPlay 2, FM and DAB+ tuners, aptX HD Bluetooth, and two HDMI inputs plus an ARC output for the television. PCM is converted by a quadruple array of eight 32-bit DACs with six selectable filters; DSD goes to T+A's True 1-Bit converter as a native stream up to DSD512. DASS isolates the digital and analog sections, each with its own power supply.

Add a pair of loudspeakers and, optionally, the PHE-P/PA R phono module for a turntable, and the system is complete. It is the right answer for a serious one-box living-room system, or for anyone who wants T+A engineering without a rack of separates. We can arrange an audition in our Portland showroom and help with system matching, delivery and setup.

The R 2500 R won the EISA Premium All-in-One award for 2024–2025, the year T+A rolled out ASA G3, the third generation of its in-house streaming architecture. It belongs to the R series that grew out of the Pulsar electronics in 1992, and it is designed, built and measured in Herford, where the company Siegfried Amft founded in 1978 is still family-owned, with his son Conradin as CEO since 2025. Read the T+A story →

Key technologies

  • Discrete double mono amplifier. Separate channel boards, J-FET input stage, low global feedback, 60 V/µs slew rate.
  • Sine-wave power supply. High-frequency sinusoidal supply combining transformer-like sound with switching-supply stability.
  • Quadruple PCM converter. Eight 32-bit sigma-delta DACs in a symmetrical layout with six oversampling algorithms.
  • True 1-Bit DSD. DSD up to DSD512 is converted as a native bitstream.
  • DASS. Galvanic isolation and separate supplies for the digital and analog sections.
  • HDMI ARC. Two HDMI inputs and an ARC output for TV sound without an AV receiver.

The MP 2500 R G3 with the PA 2500 R is the R 2500 R as separates; the Symphonia is the compact step below.

Finishes

  • Silver anodized (43) brushed aluminum
  • Black anodized (42) brushed aluminum
Specifications
Type Multi-source stereo receiver: amplifier, CD, streaming, tuner, DAC
Power output 140 W into 8 Ω, 250 W into 4 Ω (per channel)
Frequency response Power amplifier 0.5 Hz – 150 kHz; preamplifier 0.5 Hz – 300 kHz (+0/–3 dB)
Signal-to-noise 105 dB unweighted, 109 dB A-weighted; damping factor > 65
PCM conversion Double-differential quadruple converter, four 32-bit DACs per channel, up to 768 kHz
DSD T+A True 1-Bit converter, up to DSD512 native
Disc formats CD-DA, CD-R, CD-RW, CD Text
Streaming Tidal, Qobuz, Deezer, Amazon Music HD, HIGHRESAUDIO, airable; Tidal, Spotify and Qobuz Connect, AirPlay 2, Audirvana, Roon Ready
Tuner FM 87.5 – 108 MHz; DAB/DAB+ Band III
Bluetooth aptX HD, AAC, SBC (A2DP, AVRCP 1.4)
HDMI 2 × HDMI in, 1 × HDMI out with ARC
Digital inputs 1 × coaxial, 2 × optical, USB DAC (up to 768 kHz), 2 × USB host
Analog inputs RCA 250 mV – 4 V / 20 kΩ; XLR 500 mV – 8 V / 5 kΩ; optional phono MM or MC
Outputs Loudspeakers, pre-out RCA, headphone 4.4 mm Pentaconn (6 Ω)
Remote SRC 2 included
Power consumption 800 W max.; standby < 0.5 W
Dimensions (H × W × D) 16.5 × 46 × 40.5 cm (6.5 × 18.1 × 15.9 in)
Weight 14 kg (30.9 lb)
Finishes Silver anodized (43) or black anodized (42)

T+A R 2500 R product page and specifications

Where it sits in the range

T+A's one-box systems, least to most expensive:

  • T+A Caruso: all-in-one music system with built-in speakers
  • T+A Cala CDR: compact streaming CD receiver
  • T+A Symphonia: 125 W into 8 Ω streaming integrated amplifier
  • T+A R 2500 R (this model)

For separates at the same level, the PA 2500 R and MP 2500 R G3 together add SACD playback and more power supply.

Plan your T+A system with Pearl Audio

Pearl Audio is an authorized T+A dealer. We can arrange an audition in our Portland showroom and help with system matching, delivery and setup. Call (503) 222-2599 or email sales@pearlaudio.com.

Signature technologies

The engineering behind the T+A Elektroakustik T+A R 2500 R Streaming CD Receiver

T+A Elektroakustik gives its technologies names because each one solves a specific problem. Here is what each does, where it came from, why it matters in a system, and what you may hear.

Transistors run where they are most linearSince 2013

HV: high-voltage amplifier stages

T+A's HV circuits run their transistor voltage-gain stages on supply rails several times higher than ordinary solid-state designs, up to 100 V in the P 3100 HV preamplifier and up to 500 V in the M 40 HV's power stages. Each device then works over a small, linear part of its curve, as a tube does, so the circuit needs virtually no overall negative feedback. Read the deep diveClose

What it does

Most solid-state audio circuits run on low rails; Alan Sircom notes that most modern circuits run at about plus and minus 5 V. The High Voltage series, three years in development and introduced in 2012 by Siegfried Amft's account or 2013 by T+A's own, moved the voltage-gain stages to rails several times higher, with the stated aim of combining the sonic and technical advantages of tubes and transistors while avoiding the inherent disadvantages of present-day valves. In the PA 3100 HV the input is a differential cascode amplifier of individually selected audio J-FET transistors that can process signals up to 60 V peak-to-peak without distortion; the P 3100 HV runs at up to 100 V and handles 80 V peak-to-peak; the M 40 HV's power stages reach 500 V, behind a class-A input stage of 6SN7 triodes. Because each transistor works over a small, linear part of its curve, the circuit needs virtually no overall negative feedback, and bandwidth and headroom are wide: the P 3100 HV is specified from 0.5 Hz to 300 kHz. HV is used in the amplifier stages of every HV-series component, the same voltage-gain stage appears in the Series 200, the HA 200 and the Symphonia, and the PA 2500 R and PA 2000 R carry a high-voltage dual-mono design on the R-series chassis.

Why it matters in a system

An amplifier stage that stays linear without heavy feedback behaves the same from the first watt to clipping and into awkward loudspeaker loads, which is what HV owners describe as ease at volume. It is also the reason a T+A preamplifier, converter and power amplifier sound of a piece: the same voltage-gain stage sits in all of them, from the DAC 200 to the M 40 HV.

What you may hear

Jason Victor Serinus, reviewing the PA 3100 HV for Stereophile, found the midrange strong, exceptionally smooth, and all of one piece. Alan Sircom in hi-fi+ called the SDV 3100 HV extremely listenable, with extraordinary clarity and dynamics, and musically inviting.

PCM and DSD never meetSince 2015

Two converters: Quadruple PCM and True 1-bit DSD

Instead of converting DSD to PCM inside one chip, every current T+A converter carries two. PCM goes to eight 32-bit Burr-Brown sigma-delta chips, four per channel in a double-differential arrangement; DSD goes to a discrete one-bit converter of T+A's own design that never touches PCM, and relays switch between the two paths. Read the deep diveClose

What it does

T+A's converter layout dates from the DAC 8 DSD of about 2015, when Lothar Wiemann concluded that it was very difficult to preserve a true DSD signal path with ready-made chips. The PCM side is the Double-Differential-Quadruple-Converter: four 32-bit Burr-Brown sigma-delta converters per channel, run in conversion-only mode with T+A's own upsampling and filtering ahead of them, an arrangement T+A says lowers noise by 6 dB. The MP 3100 HV G3 feeds them at 352.8 or 384 kHz; the DAC 200 and PSD 3100 HV accept PCM to 768 kHz. The DSD side is the T+A True-1Bit converter, a discrete circuit that takes the native bitstream and oversamples it; T+A holds that DSD's advantages appear only when the signal is massively oversampled, and the reference converter upsamples DSD by 32 times. The DAC 200, HA 200 and SDX 3100 HV decode up to DSD 1024, or 49.2 MHz, a capability T+A introduced in the SD and SDV 3100 HV of March 2019 and calls the world's first DSD 1024-capable player; the PSD 3100 HV, MP 3100 HV G3, MP 2500 R G3, R 2500 R and Symphonia are specified to DSD 512. In 2026 T+A gave the arrangement a name, Path Separation Technology. The Symphonia uses a two-chip-per-channel Double Differential derivative of the PCM converter.

Why it matters in a system

A chip that handles DSD by first turning it into PCM, or the reverse, imposes one filter's character on both formats. Giving each its own converter means an SACD or a DSD file reaches the analog stage as the bitstream it was recorded as, and a PCM file is handled by a converter built for multi-bit data with T+A's own filters in front of it.

What you may hear

Herb Reichert, reviewing the MP 3100 HV G3 for Stereophile, wrote that the T+A's smooth, nuanced sigma-delta feels considerably different than dCS's liquidy FPGA-controlled Ring DAC, and called it CD playback at its highest imaginable level. Jim Austin heard treble that glistened, with no digital glare.

Four filters, no ringing, the listener's choiceSince 2015

Bézier oversampling filters and 56-bit DSP

T+A writes its own PCM oversampling in a signal processor instead of using the filters built into the converter chips: two FIR filters and two Bézier-polynomial filters, plus a non-oversampling mode, selectable by the owner. The Bézier filters avoid the pre- and post-ringing of conventional filters, and a third-order Bessel analog filter follows, switchable between 60 and 120 kHz. Read the deep diveClose

What it does

Every oversampling converter interpolates new samples between the ones on the disc or in the file, and the filter that does it leaves a signature; conventional linear-phase FIR filters ring before and after each transient. In the DAC 8 DSD T+A moved this work out of the converter chip and into a 56-bit signal processor running its own algorithms, and the current units offer five settings: FIR short, FIR long, Bézier/IIR, Bézier and NOS, or non-oversampling. Lothar Wiemann's point about the Bézier interpolation is that it has no pre-ringing and no post-ringing. In the reference converters a 16-times Bézier-polynomial filter takes 44.1 and 88.2 kHz material to 705.6 kHz and 48, 96 and 192 kHz material to 768 kHz before the Quadruple converter sees it. After conversion a phase-linear third-order Bessel filter, switchable between a 60 and a 120 kHz cut-off, removes what remains above the audio band without adding ringing of its own. The same processor and filter set run in the DAC 200 and HA 200, the MP 2000 R G3 and MP 2500 R G3, the R 2500 R, the PSD 3100 HV, the MP 3100 HV G3 and the SDX 3100 HV, so the choice an owner makes on a Series 200 converter is the same one offered on the reference.

Why it matters in a system

The reconstruction filter determines how a converter handles the leading edge of every note, and the ringing of a steep filter is one reason digital playback can sound hard. Letting the listener choose among FIR, Bézier and no oversampling, with an analog filter gentle enough to add nothing of its own, means the converter can be matched to the recording and to the rest of the system.

What you may hear

Jim Austin, in Stereophile on the MP 3100 HV: treble tones glisten like light reflected from the facets of a diamond, and also seem especially relaxed, with no digital glare. Craig Joyce at StereoNET called the DAC 200 a standout product that handles a wide range of music with clarity and precision.

A disc mechanism machined in Herford, not bought inSince 2019

In-house SACD transport and IPA Link

T+A builds its own disc transport: a linear-tracking laser block riding on two aluminum linear bearings inside a chassis machined from a single block of aluminum, with its own servo board, SACD decoder and control software. DSD leaves the transport as the native bitstream, and the IPA Link carries it, with its clock, to the matching converter. Read the deep diveClose

What it does

Most SACD players use a drive and decoder chipset made for Blu-ray players, and convert the disc's DSD to PCM before it goes anywhere. For the PDT 3100 HV of March 2019 T+A's engineers developed a decoder and drive mechanism from the ground up: a high-precision linear-tracking drive with a double laser, 658 nm for SACD and 790 nm for CD, a high-torque synchronous motor, an anti-resonance weight, a chassis cut from one aluminum block, two aluminum linear bearings, and a drawer that runs on stainless steel rails in PTFE and phosphor-bronze bearings. The servo board, SACD decoder and control software are T+A's own, written to deliver native DSD and PCM rather than converting DSD to PCM first; James Shannon's argument is that less error correction means greater accuracy of the decoding process. The mechanism alone weighs nearly 20 pounds. The High Res IPA Link is a proprietary connection, using low-voltage differential signalling, that transmits PCM and DSD data bit-accurately along with high-precision clocking, a constant bitstream of unchanged raw data, from the PDT 3100 HV to the SD, SDV and SDX 3100 HV. The same drive sits inside the MP 3100 HV G3 and the MP 2500 R G3, while the MP 2000 R G3, MP 200 G3 and R 2500 R use a slot-loading CD drive.

Why it matters in a system

A transport is the one part of a digital system that is still mechanical, and read errors, vibration and the conversion of DSD to PCM all happen before the converter can do anything about them. Owning the mechanism and the decoder lets T+A keep SACD native, and keep the drive in production and in service for as long as the player.

What you may hear

Robert Harley, reviewing the PDT 3100 HV with the SDV 3100 HV for The Absolute Sound, called it by far the smoothest and quietest transport he had encountered, with SACD playback vaulted into another realm. Herb Reichert found the MP 3100 HV G3 CD playback at its highest imaginable level.

Designed, programmed and certified in HerfordSince 2024

ASA G3: the in-house streaming architecture

T+A designs its own streaming hardware and software rather than buying a module. The third-generation Audiophile Streaming Architecture of 2024 is a quad-core board with Wi-Fi 6 and Gigabit Ethernet, native DSD streaming to DSD 256, Tidal, Spotify and Qobuz Connect, AirPlay 2 and Roon Ready, run from T+A's own MusicNavigator G3 app. Read the deep diveClose

What it does

Streaming boards are the part of a player most likely to be obsolete first, and most manufacturers buy them from one of a few suppliers. T+A keeps the whole chain in-house: design, PCB layout, certification, assembly, measurement, operating-system programming and app development. ASA G3 arrived on September 20, 2024 in the MP 2000 R G3 and MP 2500 R G3, in the MP 3100 HV G3 on October 18, 2024, and in the MP 200 G3 on November 28, 2024; Conradin Amft, then chief operating officer, described it as a core technology that the company would gradually implement in new products. The module streams DSD natively from the network for the first time in T+A's history; handles Tidal, Qobuz, Deezer, Amazon Music and HighResAudio, Tidal Connect, Spotify Connect and Qobuz Connect, AirPlay 2 and Roon Ready; and shares its control with the FM and DAB+ tuners the players also carry. The MusicNavigator G3 app is the controller; on the Caruso a seven-inch touchscreen runs T+A's own NavigatorOS instead. Owners of the earlier MP 3100 HV, MP 2000 R MK II, MP 2500 R and MP 200 can have their units upgraded to ASA G3 at the factory. The PSD 3100 HV, SDX 3100 HV, R 2500 R and Symphonia use the same module.

Why it matters in a system

A streamer that the manufacturer wrote itself is one the manufacturer can keep current, and the factory upgrade path shows what that means in practice: an MP 3100 HV bought in 2017 can be brought to the 2024 platform instead of being replaced. It also means the player, the app and the tuner behave as one product rather than as a module inside a box.

What you may hear

Stereophile on the R 2500 R: the app is the ideal interface, and the component just plays music and does it well. Killain Jones at SoundStage! found the R 2500 R effortlessly dynamic and able to produce deep, visceral bass.

Theory and application under one roofSince 1978

Designed, built and measured in Herford

Every T+A component is designed, assembled and measured at the company's own buildings in Herford, where it has been since 1988: circuit design, board layout, software, the MusicNavigator app, final assembly and a measurement protocol for every unit. Surface-mount board assembly is placed with a specialist using T+A-supplied parts; about 95 percent of production is in-house. Read the deep diveClose

What it does

T+A has occupied its own buildings in Herford since 1988 and added an administration, sales and laboratory building in 2003. A factory visit in April 2025 counted about 90 employees, 14 of them in research and development; T+A itself describes a team of fifteen designers and developers plus seven service technicians. The scope kept in-house runs from design, PCB layout and certification to assembly, measurement, operating-system programming and app development; the one step placed outside is surface-mount component placement, done by a specialist assembler using components T+A supplies, after which the boards return for final assembly and test. There are no assembly lines or automated placement machines, and nothing leaves the works without a measurement protocol. The company's own description is that it builds acoustic treasures rather than mass products, and it reports returning more than 98 percent of devices of any age to working condition when they come back for service. The engineering continuity is long: Lothar Wiemann, who joined as a student and developed the first electronics in 1982, was chief developer for 39 years before handing over to Jörg Küpper. In the United States, T+A North America in St. Marys, Georgia has handled distribution since August 2021, with service through Pyramid Audio in Austin and Audio Design and Service in Burbank.

Why it matters in a system

A product made in one place by the people who designed it can be supported for as long as its owner wants to keep it, and T+A's factory upgrades, the ASA G3 streaming boards fitted to players from 2017, are the practical form of that. It is also why a T+A system sounds consistent from the Series 200 to the HV line: the same small team designed all of it.

What you may hear

Jim Austin, in Stereophile on the MP 3100 HV: more than any other component he had had in his system, it radiated attention to detail. Michael Manousselis, who imported the brand to North America: they don't leave things to luck or to chance.

The Pearl Audio experience

How we work with you

A system at this level should be heard, thoughtfully matched, and properly set up. From the first audition to long-term ownership, you work with the same people, in person.

  1. 01

    Listen first

    The T+A R 2500 R Streaming CD Receiver is not in our rooms at present. When it is the right piece for a client we arrange a demonstration unit from the manufacturer and set it up for a private session.

  2. 02

    Delivery and installation

    We deliver and install throughout the Portland area, taking care of placement, connections, ventilation and system configuration ourselves.

  3. 03

    Support for as long as you own it

    We support everything we sell for as long as you own it, whether the answer comes by phone, in your home, or through factory service.

  4. 04

    A path for what comes next

    Trade-in assistance and qualifying 100% Trade-Up options give you flexibility when your listening priorities or your system change.

Search