← Back to your LP12 build

Rega · Turntable Accessories

Rega 2mm Three Point Arm Height Adjustment Spacer - Universal

$40

Upgrade part · All Rega upgrades and parts →

Signature technologiesThe Rega story

Not currently in our rooms. For a serious buyer we will often bring a piece in from the manufacturer for a private session — tell us about your system and what you are weighing it against, and we will advise.

Rega · Turntable Accessories

A laser-cut 2 mm black aluminum spacer that raises any Rega three-point tonearm for a deeper cartridge body or a non-Rega deck.

2 mm
arm height increase
3-point
fits all current Rega arms

Authorized Rega dealer · Delivery and installation by Pearl Audio · Trade-ins welcome

The story

Rega cartridges on Rega turntables need no spacer. Fit a deeper-bodied cartridge from another maker, or mount a Rega arm on another brand's turntable, and the back of the cartridge can touch the record; this spacer lifts the arm 2 mm to clear it. It is laser cut from aluminum and anodized black, a lower-cost alternative to the stainless version.

Rega's guidance is to raise the arm only if the rear of the cartridge hits the record in play; otherwise the arm should sit parallel or slightly low at the pivot.

Rega has built turntables in Southend-on-Sea since 1973 and still supports the older ones: the 24 V motor board and TT-PSU outboard supply of 2001, the Neo of 2017 and the EBLT belts it molds on its own tooling all fit decks that have been in service for years. Every part here comes from the same factory that builds the current Planar range. Read the Rega story →

Key technologies

The stainless spacer is the heavier-duty version; the 2 mm shim is the equivalent for older nut-mounted arms.

Specifications
Fits All Rega three-point tonearms
Material 2 mm aluminum, black anodized
Height increase 2 mm (about 0.08 in)
Made in England

Rega 2 mm Universal Spacer product page

Where it sits in the range

Rega's arm-height parts, ordered by price.

Plan your Rega system with Pearl Audio

Pearl Audio is an authorized Rega dealer. Tell us your arm and cartridge and we will advise whether you need one. Call (503) 222-2599 or email sales@pearlaudio.com.

Signature technologies

The engineering behind the Rega 2mm Three Point Arm Height Adjustment Spacer - Universal

Rega gives its technologies names because each one solves a specific problem. Here is what each does, where it came from, why it matters in a system, and what you may hear.

Mass absorbs energySince 1976

Low mass, high rigidity

Rega builds its turntables as light and as stiff as possible rather than heavy and damped. The argument, in the company's own words, is that mass absorbs energy and lost energy equals lost music: a heavy plinth stores vibration and releases it a moment later, while a light, rigid one lets energy pass through and dissipate. Read the deep diveClose

What it does

Roy Gandy trained as a mechanical engineer at Ford and describes a turntable as a vibration measuring machine. A record contains no energy of its own; the energy comes from the motor, the power supply and the mains, and the turntable's job is to manage the vibration and friction that imperfect mechanics introduce. His conclusion, reached early, was that a low-mass plinth and high rigidity were vital, because, as he puts it, the plinth feeds energy into the record. Rega also avoids damping materials, which turn movement into heat but in Gandy's view smear the sound; the preference is to minimize resonances, spread them over a wide bandwidth, and support the deck rigidly rather than isolate it. The 1976 Planar 3 was lighter than the Planet it replaced, and the principle has been pushed further at each step since: the skeletal RP8 and RP10 of 2012 and 2013, the foam-core Planar 6, 8 and 10, the carbon-fiber Naia, and the 2026 Replay, whose plinth weighs 2.2 kg. Rega's 2018 company history, by Bill Philpot, Paul Messenger and Roy Gandy, is titled A Vibration Measuring Machine.

Why it matters in a system

The plinth is where the stylus, the bearing and the motor meet, and whatever energy it stores comes back into the groove later as a smear on the music. A light, stiff plinth gives that energy nowhere to live. It is also why a Rega asks for a rigid, level shelf rather than a soft or isolating platform, and why the decks weigh so little for what they do.

What you may hear

Stereophile's Planar 10 review put it as "the more Rega charges for one of its turntables, the less you get," and warned that an over-damped turntable "can sound dull, dead, and lifeless." What listeners describe in a Rega is pace, timing and a clean start and stop to every note.

From the RB300 of 1983 to the RB TitaniumSince 1983

The one-piece cast RB tonearm

In 1983 Rega introduced the RB300, whose headshell and arm tube are one tapered aluminum casting with no joints, on preloaded ball-bearing gimbals. The same lineage runs through the RB110, RB220, RB330, RB880, RB3000 and RB Titanium today; the higher the model, the tighter the bearing fit and the fewer the joints. Counting OEM versions, the family has sold more than 400,000. Read the deep diveClose

What it does

The RB300 of 1983 replaced the Acos-made R200 with a tapered, one-piece cast aluminum tube running unbroken from headshell to pivot, a tungsten-alloy counterweight and a tracking-force spring; Rega worked with a casting company to develop a method for casting so long a cored hole accurately. The RB250 followed in 1984, the RB301 in 2007 and the RB303 in 2011. The current arms share one geometry, a 222 mm mounting distance, 236.5 mm effective length, 21.55 degree offset and 11 g effective mass, and differ in bearings and materials. The RB110 on the Planar 1 and the RB220 on the Planar 2 and Planar 78 use Rega's patented ultra-low-friction polymer bearings with automatic bias. The RB330 of 2016 has hand-selected ball bearings preloaded by one or two microns with no measurable free play and a tube with its mass redistributed. The RB880 of 2019 adds a stainless-steel sleeve and shaft and hand-matched bearings; the RB3000 is hand-polished, with bearings an interference fit on the spindle and no adhesive anywhere; the RB Titanium of 2023 has a one-piece titanium bearing housing and spindle and a tungsten counterweight. Gandy has said standard bearings run at about one micron of clearance after preloading and the best arms at less than one micron. Rega makes arms for about twenty other brands.

Why it matters in a system

The arm holds the cartridge still while the groove moves it, and any play in the bearings or flex at a joint is information lost. Rega's position is that such losses can never be recovered later in the chain, which is why the arm is where it spends the money, and why there is no VTA adjustment: a 2 mm spacer under the arm base does that job without a loose joint.

What you may hear

A UK retrospective called the RB300 "one of the most important tonearms of its generation, perhaps even ever." What an RB arm gives a cartridge is a stable platform, which listeners hear as secure tracking, solid images and bass that does not blur.

Bolt it down; the alignment is doneSince 1987

Three-point cartridge mounting

Rega cartridges have a third fixing hole, so on a Rega arm the cartridge bolts down in exactly the right position with overhang and alignment preset. There is nothing to adjust, which is why Rega sells most of its turntables with the cartridge already fitted at the factory. Read the deep diveClose

What it does

The third hole appeared on the Elys cartridge in 1987 and the hand-wound Exact in 1992, and Rega's arms have carried the matching third mount since the RB301 of 2007. Every current Rega cartridge except the two-screw Carbon uses it: the Nd3, Nd5, Nd7 and Nd9 moving magnets and the Ania, Ania Pro, Apheta 3 and Aphelion 2 moving coils. Rega says the method sets overhang automatically, and the Nd9 page notes it is for Rega tonearms only; on other arms the cartridges fit with the usual two screws and a protractor. The system is what makes the factory-fitted packages possible: the Planar 2 with an Nd3, the Planar 3 with an Nd3 or Nd5, the Planar 3 RS with an Nd5, the Planar 6 with an Nd5, Nd7 or Ania Pro, the Planar 6 RS with an Nd9, the Planar 8 with an Nd7, Nd9, Ania Pro or Apheta 3, and the Planar 10 with an Apheta 3 or Aphelion 2. Arm height is handled the same way: Rega does not fit VTA adjustment, which Gandy does not accept as valid or beneficial, and instead supplies 2 mm three-point spacers and shims to raise the arm base when a taller cartridge calls for it. The Atlas gauge sets tracking force.

Why it matters in a system

Alignment errors are the most common reason a good cartridge sounds poor, and a stylus that is a millimeter off its intended position distorts across the inner grooves. Three-point mounting removes the error at the source and lets the arm and cartridge be treated as one assembly, which is how Rega designs them.

What you may hear

Stereophile's review of the Planar 3 50th Anniversary observed that "The Exact's mounting is fixed in Rega's preferred alignment" and that the deck "has a real knack for allowing you to forget about audiophile affectations." The payoff is a cartridge that performs as designed from the first record.

All Rega technologies and the company story

The Rega story

Southend-on-Sea since 1973: low-mass turntables, one-piece cast tonearms and hand-built cartridges, made in England.

Founded 1973 in Southend-on-Sea, Essex, England, where every Rega is still built by Roy Gandy and Tony Relph · rega.co.uk

Milestones

  1. 1973 Rega Research registered; the Planet Ford-trained engineer Roy Gandy and Southend hi-fi dealer Tony Relph each put in 1,000 pounds and register the company on July 1, 1973, named from RElph and GAndy. The first turntable, the Planet, has a three-spoke metal platter and an Acos Lustre arm.
  2. 1976 Planar 3, then Planar 2 The Planar 3 of April 1976 introduces the 12 mm glass platter and the R200 arm, and is lighter than the Planet; the Planar 2 with a 10 mm glass platter follows in April 1977. The low-mass, high-rigidity philosophy begins here.Rega Planar 2
  3. 1983 RB300 A tonearm with headshell and tube cast as one tapered piece of aluminum, on preloaded ball bearings, with a tungsten-alloy counterweight. The RB250 follows in 1984; with OEM versions, the family sells more than 400,000.Rega RB330 Tonearm
  4. 1988 Cartridges made in-house The Elys and Bias, launched in 1987 with Rega's three-point mounting, go into in-house production in March 1988 and sell over 1,000 in the first month. The hand-wound Exact follows in 1992.
  5. 1991 Elicit, Brio and Elex After the clam-shell Elicit of 1990, the Brio and Elex integrated amplifiers of April 1991 begin the Class A/B lineage that runs to today's Brio MK7 and Elex MK4. Gandy designs a factory on the Temple Farm Industrial Estate for loudspeaker and amplifier production.Rega Brio Mk7 Integrated Amplifier
  6. 1995 Planar 9: the ceramic platter The first Rega with a ceramic platter and an external power supply, with the RB900 arm. The Kyte loudspeaker precedes it in 1993 and the Planet CD player follows in 1997.Rega Planar 10
  7. 2005 Apheta Rega's first moving-coil cartridge, with hand-wound coils on an iron micro-cross and no tie wire or damper: the design behind today's Ania, Apheta 3 and Aphelion 2.Rega Apheta 3 MC Cartridge
  8. 2009 The reference range The Ios phono stage in February, the Osiris integrated amplifier in May and the Isis and Isis Valve CD players in June. Work on the Naiad research turntable begins the same year.Rega Osiris Reference Integrated Amplifier
  9. 2013 RP8 and RP10: the skeletal plinth The RP8 of July 2012 cuts the plinth to a skeleton with a three-part flywheel glass platter; the RP10 of October 2013 adds a ceramic platter and a DSP-generated power supply. The RP3 is Stereophile's 2012 Analog Source Component of the Year.
  10. 2016 The new Planar 3 After two years of development led by Gandy, a Planar 3 carrying over just two components from the RP3: double-braced plinth, 12 mm Optiwhite glass and the new RB330. The Planar 1, Planar 2 and Brio are renewed the same year.Rega Planar 3
  11. 2017 Planar 6 and the Naiad The Planar 6 is the first Rega with a Tancast 8 foam-core plinth and the Neo power supply. The Naiad, built to push Rega's philosophies to the extreme, is limited to 50 units. The Ania moving coil and RB220 follow.Rega Planar 6
  12. 2019 Planar 10, Apheta 3 and Aethos The Planar 10 brings the ceramic platter, ceramic top brace and RB3000 to a skeletal foam-core plinth; the Planar 8 preceded it in October 2018, and the Aura phono stage in June 2018. The Aethos integrated amplifier arrives in November.Rega Planar 10
  13. 2023 Fifty years; the Naia A Planar 3 50th Anniversary Edition in May and, in September, the Naia: the production form of the Naiad, with a graphene-impregnated carbon-fiber plinth, ceramic braces and platter, a ZTA ceramic bearing and the RB Titanium.Rega Naia Reference Turntable
  14. 2024 The Nd range and employee ownership The Nd3, Nd5 and Nd7 are the first moving magnets built on an N55 neodymium magnet; the Planar 3 RS follows in November. On October 28, 2024, Roy Gandy gifts 100 percent of his shares to an Employee Ownership Trust and remains sole director.Rega Nd7 MM Cartridge
  15. 2025 Brio MK7, Mercury and Solis, Nd9 The seventh Brio in March; the Mercury preamplifier and Solis power amplifier, four years in development, in November, with the boron-cantilever Nd9. On November 17, 2025, What Hi-Fi? gives Gandy its Outstanding Contribution Award.Rega Nd9 Reference MM Cartridge
  16. 2026 AOS MC, Planar 6 RS and Replay The AOS MC phono stage, derived from the Aura, in February; the Planar 6 RS with the RB880 and Nd9 in March; the plug-and-play Replay in October. Rega employs over 150 people on one industrial estate in Southend-on-Sea.Rega Planar 6 RS Edition Turntable
Read the Rega story
Rega

Roy Gandy trained as a mechanical engineer at the Ford Motor Company and made loudspeakers in his spare time because he could not afford to buy a hi-fi; his first system used homemade speakers and a turntable he designed himself from salvaged and discounted parts. He had tinkered with machinery since the age of four, rebuilt bicycles and motorbikes and built two motorcycles from scratch, and the hand-built equipment he sold to friends led to supplying a local Southend audio shop. The shop's owner, hi-fi dealer Tony Relph, saw potential in the turntables and suggested a company; each partner put in 1,000 pounds, and Rega Research was registered on July 1, 1973, named from the first letters of RElph and GAndy. Rega's own timeline dates its first turntable, the Planet, to April 1973, with a three-spoke steel and aluminum platter and an Acos Lustre tonearm; Gandy says it sold because it looked different rather than on sound quality. The partners worked above the shop at first, then in a house Gandy gutted to make a factory.

The Planar of April 1975, with an aluminum platter, ran to only 200 units. The Planar 3 of April 1976 replaced the Planet's three metal discs with a 12 mm glass platter, which Gandy called a big step forward, and was lighter than the Planet; it carried the Acos-made R200 tonearm. The Planar 2, with a 10 mm glass platter, followed in April 1977, the year Hi-Fi News and Record Review remarked of the Planar 3 that the complete unit was worth a look. Turntable production moved into a converted mill on Park Street in Westcliff-on-Sea, and 1980 brought the R100 moving-magnet cartridge and the RTX floor-standing loudspeaker. In April 1983 came the RB300, whose headshell and arm tube are one tapered aluminum casting with no joins, a tungsten-alloy counterweight and a spring for tracking force; Rega had worked with a casting company on a new method of casting so long a cored hole. The RB250 followed in 1984. Counting every variant and the OEM arms Rega has made for NAD, Rotel and about twenty other brands, the RB300 family has sold more than 400,000.

The RB100 cartridge of 1985 was designed by Rega and made with Goldring, and the Planar 78 appeared the same year. The Elys and Bias cartridges followed in 1987, and by March 1988 Rega was building them in-house, selling over 1,000 in the first month. Electronics came next: the clam-shell Elicit integrated amplifier in May 1990, the Brio and Elex in April 1991, and the hand-wound, three-point-mounted Exact cartridge in April 1992. Gandy designed a factory on the Temple Farm Industrial Estate in Southend-on-Sea to house loudspeaker and amplifier production; the Kyte bookshelf loudspeaker arrived in September 1993, the Planar 9 with a ceramic platter and external power supply and the RB900 arm in 1995, and the Planet CD player in June 1997. Rega has advertised only once and puts the money into research instead. By 2000 the range had been renamed P2 and P3 2000, and the 24 V motor board and the first TTPSU outboard supply arrived in 2001.

The P5, P7 and P9 of 2002, the latter two with ceramic platters, brought the RB700 and RB1000 arms; the Apollo and Saturn CD players arrived in 2004, the first Apheta moving-coil cartridge in March 2005 and the P1 that June, and the three-point RB301 and P3-24 in 2007. In 2009 Rega launched a reference range: the Ios phono stage in February, the Osiris integrated amplifier in May and the Isis and Isis Valve CD players in June. The RP1 of 2010 introduced the phenolic-resin platter, the RP3 and RP6 followed in 2011, and the RP3 won Stereophile's Analog Source Component of the Year for 2012. The RP8 of July 2012 brought the skeletal plinth and a three-part flywheel glass platter, the RP10 of October 2013 the skeletal plinth with a ceramic platter, and 3,000 RP40 anniversary decks marked forty years. The Apheta 2 came in 2014 and the Aphelion in 2015. Around 2013 Rega employed almost 90 people and made about 2,000 turntables a month; the Temple Farm site was expanded with a new building and mezzanine in 2014 and 2015, and the Naiad, a research project begun in 2009, was shown to visitors in 2015.

In 2016 Rega rebuilt its entry decks: the Planar 2 in May, the Planar 1 in July, the RB330 in August and in October a Planar 3 that carried over just two components from the RP3 after two years of work led by Gandy. The Neo power supply, Planar 1 Plus, Planar 6, Ania and RB220 followed in 2017, along with the Naiad, built to push Rega's philosophies to the extreme in a run of 50. The Aura phono stage, largely the work of chief electronics designer Terry Bateman, came in June 2018 and the Naiad-inspired Planar 8 that October; 2019 brought the RB880, Apheta 3, Planar 10 and Aethos; 2020 the Ania Pro, Aphelion 2 and io. Staff numbered 140 by 2020, with output of several thousand turntables a month. The Kyte returned in 2021 with the Fono MM MK5, Fono MC MK4 and Neo MK2, the Elicit MK5 and Elex MK4 arrived in 2022, and in 2023 Rega marked fifty years with a Planar 3 50th Anniversary Edition in May and, in September, the Naia, the production form of the Naiad, and the AYA loudspeaker.

The Nd3, Nd5 and Nd7 of 2024 were the first moving-magnet cartridges built on an N55 neodymium magnet, and the Planar 3 RS, RS standing for Rega Special, followed in November. On October 28, 2024, Roy Gandy gifted 100 percent of his shares to an Employee Ownership Trust, taking no financial gain; every employee became a beneficiary, the trust is barred from selling the company, and Gandy remains sole director, working in research and sales. The Brio MK7 arrived in March 2025, the Mercury preamplifier, Solis power amplifier and Nd9 in November 2025, and on November 17, 2025, What Hi-Fi? gave Gandy its Outstanding Contribution Award. The AOS MC phono stage came in February 2026, the Planar 6 RS in March and the Replay in October. Rega today employs over 150 people, designs and hand-assembles every product in custom-built facilities on one industrial estate in Southend-on-Sea totaling almost 70,000 square feet, exports to more than fifty countries and backs every product with a lifetime limited warranty against manufacturing defects. Phil Freeman is managing director, and the United States is served through The Sound Organisation in Arlington, Texas.

The complete Rega story and technology library

Rega at Pearl Audio

Pearl Audio is an authorized Rega dealer in Portland. We carry the range from the Planar 1 to the Naia, the RB tonearms, the Nd and moving-coil cartridges, the io through Osiris amplifiers and the Mercury and Solis, the Fono, AOS and Aura phono stages, the Isis players and the Kyte, and we order factory-fitted turntable and cartridge combinations to suit the rest of your system. Our staff set up and level Rega turntables, fit and align cartridges, set tracking force, and match decks, phono stages and amplifiers to your loudspeakers and your room. We deliver and install in your home and are here for upgrades, from a Neo power supply or a new cartridge to the next deck up.

The Pearl Audio experience

How we work with you

A system at this level should be heard, thoughtfully matched, and properly set up. From the first audition to long-term ownership, you work with the same people, in person.

  1. 01

    Listen first

    The 2mm Three Point Arm Height Adjustment Spacer - Universal is not in our rooms at present. When it is the right piece for a client we arrange a demonstration unit from the manufacturer and set it up for a private session.

  2. 02

    Delivery and installation

    We deliver and install throughout the Portland area, taking care of placement, connections, ventilation and system configuration ourselves.

  3. 03

    Support for as long as you own it

    We support everything we sell for as long as you own it, whether the answer comes by phone, in your home, or through factory service.

  4. 04

    A path for what comes next

    Trade-in assistance and qualifying 100% Trade-Up options give you flexibility when your listening priorities or your system change.

Search