← Back to your LP12 build

DS Audio · TB-100

DS Audio TB-100 Tube Phono Equalizer

$22,000

Signature technologiesThe DS Audio story

Not currently in our rooms. For a serious buyer we will often bring a piece in from the manufacturer for a private session — tell us about your system and what you are weighing it against, and we will advise.

DS Audio · TB-100

The TB-100 is DS Audio's all-tube equalizer for optical cartridges: quad-matched ECC82s in a twin-mono layout, a wideband transformer input and response within 1 dB from 10 Hz to 70 kHz.

Works with every DS Audio optical cartridge; RCA in and out only.

4 × ECC82
quad-matched to 1%
10 Hz–70 kHz
within −1 dB
500 mV
output at 1 kHz
18.7 kg
weight

Authorized DS Audio dealer · Delivery and installation by Pearl Audio · Trade-ins welcome

The story

A DS Audio optical cartridge has no magnets or coils. A beryllium shading plate on the cantilever moves between an LED and a photodetector, with a separate pair for each channel, and the output is a current proportional to the stylus's position rather than its velocity. That signal cannot go into an ordinary phono stage: it needs an equalizer that powers the LEDs through the tonearm cable, converts the photodetector signal and applies the correct equalization. The TB-100 does all of that amplification with tubes.

Each channel uses two ECC82 (12AU7) tubes, one for voltage gain and one as a low-impedance cathode-follower output buffer, matched in-house to within 1%, or 0.1 dB. A wideband input transformer converts the photodetector's current into a voltage while keeping the channels precisely in phase. Construction is twin mono, with an independent ground and power transformer for each channel, and a separate low-noise regulated supply feeds the cartridge's LEDs and the photodiode bias.

Hi-Fi News described the TB-100 as warmer and more romantic than DS Audio's cool, precise solid-state equalizers, more open, with voices more clearly separated and more natural, and said the reviewer would buy one without hesitation. Output is 500 mV at 1 kHz from about 700 Ω through RCA only, so plan on an RCA connection to your preamplifier. It works with any DS Audio optical cartridge.

DS Audio's equalizers were solid-state from the DS-W1 of 2014 until the TB-100, the company's first all-tube equalizer, made its US debut in February 2025; the hybrid TB-50 was announced in May 2026. Both come from the Sagamihara company that Tetsuaki Aoyagi established in 2013 to read the groove with light, and both drive any DS Audio cartridge. Read the DS Audio story →

Key technologies

  • Quad-matched ECC82s. Two per channel, matched to within 1% with DS Audio's own tools.
  • Cathode-follower output. Low-impedance buffer stage for a transparent, dynamic output.
  • Wideband transformer input. Converts the photodiode current to voltage and keeps the channels phase-aligned.
  • Twin mono. Independent grounds and power transformers per channel.
  • Dedicated cartridge supply. Low-noise regulated supply for LED power and photodiode bias.

The TB-50 is the smaller hybrid alternative; the DS-W3 Equalizer is the solid-state equalizer with balanced outputs.

Specifications
Type All-tube equalizer and power supply for DS Audio optical cartridges, twin mono
Tubes 4 × ECC82 (12AU7), quad-matched to within 1%
Rated output 500 mV at 1 kHz
Output impedance 700 Ω
Frequency response 10 Hz – 70 kHz within −1 dB
Inputs RCA
Outputs RCA
Low-cut filter Not published by DS Audio
Compatibility DS Audio optical cartridges only
Dimensions (W × H × D) 17.3 × 5.9 × 19.0 in (440 × 150 × 482 mm)
Weight 41.2 lb (18.7 kg)

DS Audio TB-100 product page and specifications

Where it sits in the range

DS Audio's equalizers for optical cartridges.

The hybrid TB-50 offers a taste of the same tube output stage at a lower price.

Reviews

Plan your DS Audio system with Pearl Audio

Pearl Audio is an authorized DS Audio dealer. We can match an equalizer to your DS cartridge and system, set the low-cut filter for your loudspeakers, and arrange an audition in our Portland showroom. Call (503) 222-2599 or email sales@pearlaudio.com.

Signature technologies

The engineering behind the DS Audio TB-100 Tube Phono Equalizer

DS Audio gives its technologies names because each one solves a specific problem. Here is what each does, where it came from, why it matters in a system, and what you may hear.

Light in place of magnets and coilsSince 2013

The optical generator

A DS Audio cartridge has no magnet and no coil in its moving system. The cantilever carries a shading plate 100 microns thick between an LED and a photodiode; as the stylus moves the plate, the light reaching the photodiode changes, and the photodiode's output follows the stylus. The signal is analog from groove to equalizer. Read the deep diveClose

What it does

In a moving-magnet or moving-coil cartridge the cantilever has to drag a magnet or a coil through a magnetic field, and the field pulls back. DS Audio's generator replaces both with light: an LED shines past a light-shading plate fixed to the cantilever onto a photodiode, and the plate's shadow grows and shrinks with the stylus motion. DS Audio describes the system as capturing shadow changes, brightness changes, with LEDs and photocells, and says no magnetic resistance is generated when the vibration system moves; the moving part is a plate only 100 microns thick. The idea is older than the company. Philco sold a record player in 1941 that played mono 78s with a bulb and a mirror on the cantilever, and in the 1970s Toshiba, Sharp, Trio and Kenwood sold photoelectric cartridges, the best known being Toshiba's C-100P. Those designs used an incandescent bulb whose heat warmed the damper rubber and shifted the cartridge's compliance over time, and they disappeared when research money moved from analog to CD. Tetsuaki Aoyagi's first prototype, built after dismantling a C-100P, used an LED and a photodetector bought in Akihabara; because the LED is not a heat source, as he put it, it can be positioned very close to the shutter, and DS Audio pairs it with photodiodes selected for matching sensitivity.

Why it matters in a system

Jonathan Valin of The Absolute Sound summarized the case: magnets and coils create magnetic resistance that impedes tracking and add mass the cantilever must move, and a light beam avoids both. With less moving mass the stylus follows the groove more closely, and with no magnetic drag there is nothing pulling against it. The equalizer that completes the system is covered separately; the cartridge itself is a purely analog transducer, a point Aoyagi has had to make repeatedly.

What you may hear

Michael Trei, reviewing the DS-W3 for Stereophile, wrote that the cartridge is not bright or dark, warm or rich, but can be all those things when the recording demands it. Reviewers of every generation describe the same absence of a fixed character, and a sense of ease in difficult passages.

Why every DS Audio cartridge needs its own phono stageSince 2013

Amplitude-proportional output and the optical equalizer

A magnetic cartridge generates voltage in proportion to stylus velocity, so its output rises with frequency; an optical cartridge's output follows stylus displacement and is essentially flat. The RIAA correction it needs is different and far simpler, and the equalizer also supplies power to the LEDs through the tonearm's ground conductors. That is why a DS Audio cartridge cannot plug into an MM or MC phono stage, and why the equalizer is part of the system. Read the deep diveClose

What it does

The RIAA curve applied when a record is cut is largely a velocity-domain curve, and a magnetic cartridge needs the full inverse of it. An optical cartridge reads how far the stylus has moved rather than how fast, so, in DS Audio's words, it outputs flat from the low frequencies to the high, and the correction circuit becomes overwhelmingly simple: Hi-Fi News describes only a fairly modest high-frequency boost for a flat response from RIAA-equalized LPs. The other half of the equalizer's job is to power the cartridge. The LED supply travels from the equalizer over the two negative conductors of a standard four-conductor tonearm cable, so the tonearm's four cables must be properly independent; no special cable is needed. Because amplitude reading boosts the lowest frequencies, every DS Audio equalizer carries selectable low-frequency roll-off: four points on the DS 003, DS-W3 and TB-100, six on the Master3 and Grand Master, and a 20 Hz subsonic filter on the DS-E3's second output. The equalizers scale with the cartridges, from the op-amp DS-E3 unit to the discrete, point-to-point DS 003, the balanced DS-W3, the 23 kg dual-mono Master3 with three transformers, and the two-chassis Grand Master with 2.34 million and 2.97 million microfarads of capacitance in its equalizer and power supply. Any DS Audio cartridge works with any DS Audio equalizer.

Why it matters in a system

The equalizer is not an accessory; it is the second half of the generator, and it sets how much of the cartridge you hear. Because the cartridges and equalizers are mix-and-match across the range, the usual path is to start with a matched system and upgrade one half at a time, and the bass-filter choices let the same cartridge be tuned to a warped record, a suspended turntable or a full-range system without changing anything else.

What you may hear

Jonathan Valin, moving from the Master1 equalizer to the Grand Master equalizer, found it better in every conceivable way. Jason Thorpe of SoundStage! called the DS 003 cartridge and equalizer together, at their 2022 price of $6,000, an absolute steal.

Circuits published, no license feeSince 2021

The open optical-equalizer standard

In February 2021 DS Audio published its optical-equalizer circuit diagrams and offered a free design review to any manufacturer, with no license or consultancy fee. Equalizers from Soulution, EMM Labs, Esoteric, Aavik, Ayre, Soulnote, Westminster Lab and others are now listed by DS Audio as compatible, and any of them will drive any DS Audio cartridge. Read the deep diveClose

What it does

Tetsuaki Aoyagi's stated goal is that optical cartridges move from being unique to being popular, and his route to it was to give the equalizer away. The first third-party unit came in September 2020, when Ed Meitner of EMM Labs designed the DS-EQ1 in direct collaboration with Aoyagi; in February 2021 DS Audio made the program public, releasing its circuit diagrams and promising to review any manufacturer's design free of charge and to list approved products as compatible. Aoyagi has said that manufacturers kept asking what the license fee was, and that he never asked for one, because the market has to be built together and he does not regard other makers as competitors. As of November 2026 DS Audio's compatibility list includes the Soulution 757, shown at Munich in 2023; the Esoteric E1; Aavik's R-880 and R-x88 series; the Engström M-Optic; Reed; EMM Labs' DS-EQ1 and DS-EQ2 and their Meitner Audio versions; Soulnote's E-3 and E-2 ver.2; the Ayre PX-8; the Uesugi UB220R; Phasemation; the Wattson Madison; Westminster Lab's Quest and Monologue; Mavis Lab; the Thivan Labs Ultimate 300; the Exposure 5510; and the Keces S4 and EP+. Michael Trei noted in Stereophile that cartridges and equalizers can now be mixed and matched across brands, and that Meitner will no longer make phono preamps for conventional cartridges.

Why it matters in a system

A cartridge that only works with its maker's phono stage is a closed system; a format with a dozen independent equalizer makers behind it is a third standard beside moving magnet and moving coil. For an owner it means a DS Audio cartridge can be paired with the electronics house whose amplification they already use, and that the choice of equalizer can be made on sound rather than necessity.

What you may hear

Jason Thorpe of SoundStage! wrote that the EMM Labs DS-EQ1 stacks up as one of the best components he had come across; the point of the program is that such a unit and a DS Audio equalizer can be compared on the same cartridge.

Current in, tubes outSince 2025

Tube equalization: TB-100 and TB-50

The TB-100 is DS Audio's all-tube equalizer: a photodiode is a current source, so the TB-100 converts current to voltage at a wideband transformer input and then amplifies with quad-matched 12AU7 tubes in a twin-mono layout. The TB-50, announced May 26, 2026, keeps solid-state gain and equalization and adds a single ECC82 output buffer. Read the deep diveClose

What it does

The TB-100 made its US debut at the Florida International Audio Expo in February 2025 at $20,000. Its input is a transformer that takes the photodiode's current and turns it into voltage, flat within 1 dB from 10 Hz to 70 kHz; from there each channel runs through one ECC82/12AU7 voltage amplifier and one cathode-follower buffer, four tubes in all, quad-matched within 1 percent, or 0.1 dB. The layout is fully twin-mono, with independent grounds and separate power transformers for each channel and a dedicated low-noise supply for the cartridge's LEDs and photodetectors. Four bass curves are offered, with 50 Hz or 30 Hz turnover and a 20 Hz subsonic filter at 6 dB per octave; output is 500 mV at 700 ohms on RCA, in a chassis of 44 by 15 by 48.2 cm weighing 18.7 kg. The TB-50, announced on May 26, 2026 at 660,000 yen for a July 2026 release in Japan, is the hybrid: solid-state gain and RIAA with a current-drive input, a single ECC82 as output buffer, dimmable tube lighting and a heat duct, 500 mV output at about 700 ohms, 420 by 120 by 320 mm and 11.3 kg. DS Audio's description of it is precise solid-state amplification with the harmonic expression of vacuum tubes.

Why it matters in a system

Converting current to voltage at the input, rather than loading the photodiode with a resistor, is how the TB-100 gets a transformer and tubes into a format whose source is a photodiode. The two models give the range a choice of character at two price levels, and both share the bass filtering and the LED supply of the solid-state equalizers, so either can be dropped into an existing DS Audio system.

What you may hear

The TB-100 is new enough that no full review appears in our sources; DS Audio's claim is that the tube stage adds the harmonic expression only tubes provide without giving up the precision of its solid-state designs.

All DS Audio technologies and the company story

The DS Audio story

Japanese cartridges that read the groove with light, each with an equalizer to match.

Founded 2013 in Sagamihara, Kanagawa, Japan, where every cartridge is assembled and aligned by Tetsuaki Aoyagi · ds-audio-w.biz

Milestones

  1. 1941 A beam of light Philco's record player reads the stylus with light. In the 1970s Toshiba and other Japanese makers revive the idea, but their lamps run hot and the optical cartridge is set aside when the compact disc arrives.
  2. 2013 DS Audio established Tetsuaki Aoyagi founds DS Audio within Digital Stream Corporation, an optical-engineering firm in Sagamihara, to build an optical cartridge with an LED and modern parts.
  3. 2014 DS-W1 The first DS Audio cartridge to be offered outside Japan.
  4. 2016 Master1 A flagship with a sapphire cantilever, shown at High End Munich.
  5. 2020 Grand Master: the third generation A separate LED and sensor for each channel, a stronger output and a beryllium shading plate.DS Audio Grand Master Equalizer
  6. 2021 The equalizer circuit made public DS Audio publishes its equalizer circuits for any maker to use, without a license fee. The DS 003 brings the third generation to the middle of the range.DS Audio DS 003 Optical Phono Cartridge
  7. 2022 DS-W3 and ES-001 The DS-W3 arrives with a boron cantilever, and the ES-001 shows how far off-center a record sits so that it can be centered.DS Audio DS-W3 Optical Phono Cartridge
  8. 2023 Master3 and Grand Master EX The Grand Master EX is the first cartridge with cantilever and stylus cut from a single diamond.DS Audio Grand Master Extreme Optical Phono Cartridge
  9. 2024 DS-E3 The third generation reaches the first model in the range.DS Audio DS-E3 Optical Phono Cartridge
  10. 2025 TB-100 and the mono cartridges DS Audio's first tube equalizer, and mono versions of the stereo cartridges.
  11. 2026 TB-50 A second tube equalizer joins the range.DS Audio TB-50 Tube Phono Equalizer
Read the DS Audio story
DS Audio

Music on a beam of light

The optical cartridge is older than DS Audio. In 1941 the American maker Philco offered a record player that read the movement of its stylus with a beam of light, and then turned to war work. In the 1970s Toshiba and other Japanese makers revived the idea. Their cartridges were admired for their sound, but the small lamps inside ran hot and made them fragile, and when the industry's attention moved to the compact disc the optical cartridge was set aside.

Tetsuaki Aoyagi

DS Audio takes its initials from Digital Stream Corporation, an optical-engineering firm in Sagamihara, Kanagawa. Tetsuaki Aoyagi was working there, and was not yet a record listener, when he heard an LP played through one of those 1970s Toshiba cartridges. The clarity and life of it surprised him, and he reasoned that the same idea built with modern parts should be better still: a cool-running LED in place of the lamp, and Digital Stream's experience with light sensors behind it. DS Audio was established in 2013, and its first cartridge to reach listeners outside Japan, the DS-W1, followed in early 2014.

How it works

Two questions come up first: does it read the groove with light, and is the signal digital? No to both. A diamond stylus on a cantilever rides the groove exactly as in any cartridge, and the signal stays analog from groove to loudspeaker. The difference is inside. Where a moving-magnet cartridge carries magnets on its cantilever and a moving-coil carries coils of wire, an optical cartridge carries only a tiny shading plate. An LED shines past the plate onto a light sensor, and as the stylus moves, the light reaching the sensor rises and falls with the music.

Two things follow. The moving parts are far lighter, so the stylus is freer to follow the groove. And because the cartridge reads how far the stylus moves, where a magnetic cartridge reads how fast, it needs its own equalizer in place of a phono stage. The cartridge itself mounts and aligns like any other, in most tonearms.

Three generations

The Master1 of 2016, with a sapphire cantilever, was the cartridge that fulfilled the promise of the first design. The third generation began with the Grand Master of 2020: a separate LED and sensor for each channel, a stronger output, and a shading plate of pure beryllium at half the weight of the one before. That design has since come to the whole range, to the DS 003, the DS-W3 and the Master3, and in 2024 to the DS-E3. At the top, the Grand Master EX of 2023 has its cantilever and stylus cut from a single diamond.

An open design

DS Audio's stated aim is to make the optical cartridge a lasting part of record playing, and not only its own product. In 2021 it published its equalizer circuits for any maker to use, without a license fee, and a number of respected electronics makers now build optical equalizers of their own. Any DS Audio cartridge works with any of these equalizers, so the cartridge and the equalizer can be chosen, and later improved, separately. DS Audio's own equalizers now include tube designs, the TB-100 and TB-50.

Made in Sagamihara

Every cartridge is assembled and aligned by hand in Sagamihara, checked under a microscope, and given its own record. The company also makes accessories for record playing, among them a device that shows how far off-center a record sits on the platter so that it can be centered, and an ionizer that removes static.

How they sound

Reviewers return to the same words: clarity, speed and transparency, against a very quiet, black background and without grain. They describe dense recordings opened up so that each instrument has its own place, a deep, three-dimensional picture, and tonal richness with little character added by the cartridge itself.

The complete DS Audio story and technology library

DS Audio at Pearl Audio

Pearl Audio is an authorized DS Audio dealer in Portland. An optical cartridge needs its own equalizer in place of a phono stage, so we choose the two together with you, confirm that the cartridge suits your tonearm, and install and align it ourselves.

The Pearl Audio experience

How we work with you

A system at this level should be heard, thoughtfully matched, and properly set up. From the first audition to long-term ownership, you work with the same people, in person.

  1. 01

    Listen first

    The TB-100 Tube Phono Equalizer is not in our rooms at present. When it is the right piece for a client we arrange a demonstration unit from the manufacturer and set it up for a private session.

  2. 02

    Delivery and installation

    We deliver and install throughout the Portland area, taking care of placement, connections, ventilation and system configuration ourselves.

  3. 03

    Support for as long as you own it

    We support everything we sell for as long as you own it, whether the answer comes by phone, in your home, or through factory service.

  4. 04

    A path for what comes next

    Trade-in assistance and qualifying 100% Trade-Up options give you flexibility when your listening priorities or your system change.

Search