← Back to your LP12 build

DS Audio · DS-W3

DS Audio DS-W3 System

$16,500

Signature technologiesThe DS Audio story

Not currently in our rooms. For a serious buyer we will often bring a piece in from the manufacturer for a private session — tell us about your system and what you are weighing it against, and we will advise.

DS Audio · DS-W3

The DS-W3 System pairs the boron-cantilever DS-W3 optical cartridge with its full-size balanced equalizer: a complete optical front end that reviewers heard as close to DS Audio's flagship.

System price includes the DS-W3 cartridge and DS-W3 Equalizer. Specify stereo or mono cartridge.

70 mV
cartridge output
Boron
cantilever
XLR + RCA
equalizer outputs
7.9 g
cartridge weight

Authorized DS Audio dealer · Delivery and installation by Pearl Audio · Trade-ins welcome

The story

A DS Audio system pairs an optical cartridge with the equalizer built for it, so the two are matched from the start and you add nothing but a turntable and tonearm. The DS-W3 cartridge reads the groove with light: a beryllium shading plate on a boron cantilever moves between an LED and a photodetector, with a separate pair for each channel, and output is 70 mV. There are no magnets or coils, so there is no magnetic drag on the cantilever. A line-contact stylus and an aluminum body complete it, and channel separation is 27 dB or more.

The DS-W3 Equalizer powers the cartridge through the tonearm cable and applies the equalization. Its 2.0 mm board with 70 µm copper foil was re-optimized for the third-generation cartridges, and it delivers 500 mV at line level through two pairs of balanced XLR and two pairs of RCA outputs, with a four-position low-cut selector.

Stereophile's Michael Trei heard deep, sharply drawn soundstaging and a rare ability to untangle dense mixes, with no obvious coloration, and ran the 7.9 g cartridge happily in a 14 g effective-mass arm. Jonathan Valin in The Absolute Sound heard much of the Grand Master's character, with bass power, a very quiet background and a tape-like continuity, and reminded readers to ground the equalizer properly. The system plugs into any line-level input, so no phono stage is needed.

DS Audio has sold its cartridges with a matching equalizer since the DS-W1 of 2014, the first optical cartridge exported from Tetsuaki Aoyagi's company in Sagamihara, Kanagawa. The third generation that began with the Grand Master of October 2020 gave each channel its own LED and photodetector and a beryllium shading plate, and by the DS-E3 of July 2024 every cartridge in the range was built that way, each with an equalizer designed alongside it. Read the DS Audio story →

Key technologies

The DS-W3 cartridge and the DS-W3 Equalizer are each sold alone.

Specifications
Includes DS-W3 optical cartridge and DS-W3 Equalizer
Cartridge output 70 mV
Cartridge tracking force Not published by DS Audio on its product page; ask us for the current recommendation
Cartridge weight 7.9 g
Stylus / cantilever Line contact / boron
Cartridge body Aluminum
Channel separation 27 dB or more at 1 kHz
Equalizer output 500 mV at 1 kHz; 120 Ω; load 10 kΩ or more
Equalizer inputs / outputs 1 pair RCA / 2 pairs XLR and 2 pairs RCA
Low-cut filter Four selectable settings
Equalizer dimensions (W × H × D) 17.7 × 4.7 × 17.1 in (450 × 120 × 435 mm)
Equalizer weight 29.8 lb (13.5 kg)

DS Audio DS-W3 product page and specifications

Where it sits in the range

DS Audio's complete cartridge-and-equalizer systems.

The cartridge and equalizer are also sold separately.

Reviews

Plan your DS Audio system with Pearl Audio

Pearl Audio is an authorized DS Audio dealer. We can mount and align the cartridge on your tonearm, set up the equalizer, and arrange an audition of the complete system in our Portland showroom. Call (503) 222-2599 or email sales@pearlaudio.com.

Signature technologies

The engineering behind the DS Audio DS-W3 System

DS Audio gives its technologies names because each one solves a specific problem. Here is what each does, where it came from, why it matters in a system, and what you may hear.

Light in place of magnets and coilsSince 2013

The optical generator

A DS Audio cartridge has no magnet and no coil in its moving system. The cantilever carries a shading plate 100 microns thick between an LED and a photodiode; as the stylus moves the plate, the light reaching the photodiode changes, and the photodiode's output follows the stylus. The signal is analog from groove to equalizer. Read the deep diveClose

What it does

In a moving-magnet or moving-coil cartridge the cantilever has to drag a magnet or a coil through a magnetic field, and the field pulls back. DS Audio's generator replaces both with light: an LED shines past a light-shading plate fixed to the cantilever onto a photodiode, and the plate's shadow grows and shrinks with the stylus motion. DS Audio describes the system as capturing shadow changes, brightness changes, with LEDs and photocells, and says no magnetic resistance is generated when the vibration system moves; the moving part is a plate only 100 microns thick. The idea is older than the company. Philco sold a record player in 1941 that played mono 78s with a bulb and a mirror on the cantilever, and in the 1970s Toshiba, Sharp, Trio and Kenwood sold photoelectric cartridges, the best known being Toshiba's C-100P. Those designs used an incandescent bulb whose heat warmed the damper rubber and shifted the cartridge's compliance over time, and they disappeared when research money moved from analog to CD. Tetsuaki Aoyagi's first prototype, built after dismantling a C-100P, used an LED and a photodetector bought in Akihabara; because the LED is not a heat source, as he put it, it can be positioned very close to the shutter, and DS Audio pairs it with photodiodes selected for matching sensitivity.

Why it matters in a system

Jonathan Valin of The Absolute Sound summarized the case: magnets and coils create magnetic resistance that impedes tracking and add mass the cantilever must move, and a light beam avoids both. With less moving mass the stylus follows the groove more closely, and with no magnetic drag there is nothing pulling against it. The equalizer that completes the system is covered separately; the cartridge itself is a purely analog transducer, a point Aoyagi has had to make repeatedly.

What you may hear

Michael Trei, reviewing the DS-W3 for Stereophile, wrote that the cartridge is not bright or dark, warm or rich, but can be all those things when the recording demands it. Reviewers of every generation describe the same absence of a fixed character, and a sense of ease in difficult passages.

Why every DS Audio cartridge needs its own phono stageSince 2013

Amplitude-proportional output and the optical equalizer

A magnetic cartridge generates voltage in proportion to stylus velocity, so its output rises with frequency; an optical cartridge's output follows stylus displacement and is essentially flat. The RIAA correction it needs is different and far simpler, and the equalizer also supplies power to the LEDs through the tonearm's ground conductors. That is why a DS Audio cartridge cannot plug into an MM or MC phono stage, and why the equalizer is part of the system. Read the deep diveClose

What it does

The RIAA curve applied when a record is cut is largely a velocity-domain curve, and a magnetic cartridge needs the full inverse of it. An optical cartridge reads how far the stylus has moved rather than how fast, so, in DS Audio's words, it outputs flat from the low frequencies to the high, and the correction circuit becomes overwhelmingly simple: Hi-Fi News describes only a fairly modest high-frequency boost for a flat response from RIAA-equalized LPs. The other half of the equalizer's job is to power the cartridge. The LED supply travels from the equalizer over the two negative conductors of a standard four-conductor tonearm cable, so the tonearm's four cables must be properly independent; no special cable is needed. Because amplitude reading boosts the lowest frequencies, every DS Audio equalizer carries selectable low-frequency roll-off: four points on the DS 003, DS-W3 and TB-100, six on the Master3 and Grand Master, and a 20 Hz subsonic filter on the DS-E3's second output. The equalizers scale with the cartridges, from the op-amp DS-E3 unit to the discrete, point-to-point DS 003, the balanced DS-W3, the 23 kg dual-mono Master3 with three transformers, and the two-chassis Grand Master with 2.34 million and 2.97 million microfarads of capacitance in its equalizer and power supply. Any DS Audio cartridge works with any DS Audio equalizer.

Why it matters in a system

The equalizer is not an accessory; it is the second half of the generator, and it sets how much of the cartridge you hear. Because the cartridges and equalizers are mix-and-match across the range, the usual path is to start with a matched system and upgrade one half at a time, and the bass-filter choices let the same cartridge be tuned to a warped record, a suspended turntable or a full-range system without changing anything else.

What you may hear

Jonathan Valin, moving from the Master1 equalizer to the Grand Master equalizer, found it better in every conceivable way. Jason Thorpe of SoundStage! called the DS 003 cartridge and equalizer together, at their 2022 price of $6,000, an absolute steal.

From the Grand Master of 2020 to the DS-E3Since 2020

Third-generation optics: one LED per channel, beryllium shading plates

The first two generations of DS Audio cartridges used one shading plate and shared optics for both channels. From the Grand Master of October 2020, each channel has its own LED and photodetector, output rises from 40 mV to 70 mV, and the shading plate is 99.9 percent beryllium at half the mass of the old aluminum one. Every current DS Audio cartridge, down to the entry DS-E3, is built this way. Read the deep diveClose

What it does

The Grand Master was the first third-generation DS Audio cartridge, and its two changes to the generator have since reached the whole range. Giving the left and right channels independent LEDs and photodetectors raised output from 40 mV to 70 mV and, in DS Audio's words, eliminated crosstalk between the channels, with high-frequency separation improved by 10 dB. The light-shading plate was changed from aluminum to 99.9 percent pure beryllium and made smaller, which took its mass from 1.56 mg to 0.74 mg; DS Audio puts that at under one-tenth the moving mass of a typical moving-coil coil assembly. The internal wiring was made 1.6 times thicker. The DS 003 of 2021 to 2022, whose dual-mono generator DS Audio describes as derived from the Grand Master, brought the design to an aluminum-cantilever, line-contact cartridge in an A5052 aluminum body with 27 dB of separation; the DS-W3 of September 2022 added a boron cantilever; the Master3 and Grand Master EX of 2023 carried diamond cantilevers; and the DS-E3 of July 2024 put the same independent optics and beryllium plate into the entry model, with an aluminum cantilever, a solid elliptical stylus, more than 70 mV of output and more than 26 dB of separation at 1 kHz. Mono versions of the stereo cartridges, on brass bases, followed in May 2025.

Why it matters in a system

Separation and output are where a cartridge either preserves or loses the space in a recording, and the third generation improved both at once while cutting the mass the stylus has to move. Because the change reached the DS-E3, the entry cartridge now has the same generator architecture as the flagship; what you pay for above it is the cantilever, the stylus profile, the body and the equalizer.

What you may hear

Jason Thorpe of SoundStage! proclaimed the DS 003 an astonishing value; Tom Martin of The Absolute Sound found its sound all gain and essentially no pain, and called it his favorite cartridge at the time. Chris Frankland of hi-fi+ gave the DS-E3 a superb performance and his recommendation.

Master3, Grand Master and Grand Master EXSince 2020

Diamond cantilevers and the one-piece diamond stylus

The Grand Master of 2020 was DS Audio's first cartridge with a diamond cantilever and MicroRidge stylus. The Master3 of 2023 uses a square-pillar diamond cantilever with a bonded MicroRidge tip, and the Grand Master EX of the same year carves cantilever and stylus from a single 0.22 mm-square diamond, so there is no glue joint between the groove and the generator. Read the deep diveClose

What it does

DS Audio's cantilevers step up with the range: aluminum on the DS-E3 and DS 003, boron on the DS-W3, and diamond from the Master3 upward. The Grand Master, announced in October 2020, was the first DS Audio cartridge to feature a diamond cantilever with a MicroRidge stylus, in an Ultra Duralumin body at 7.7 g. The Master3, announced in Japan in May 2023 and on sale in the UK that November as the successor to the 2016 Master1, uses a square-pillar diamond cantilever with a MicroRidge tip, a beryllium shading plate and an Ultra Duralumin body, with output raised from the Master1's 40 mV to more than 70 mV; Hi-Fi News's lab measured 29 dB of separation at 1 kHz, compliance of 11 cu vertical and 15 cu lateral and a 24-degree vertical tracking angle, and called its tracking the most secure of any DS Audio cartridge yet. The Grand Master EX, launched in June 2023, keeps the Grand Master's optics and body and replaces the bonded assembly with a cantilever and MicroRidge tip cut from one 0.22 mm-square diamond in a stainless-steel holder. Musical Surroundings' description is that the one-piece cantilever more accurately transmits the groove modulation to the third-generation generator. Styli and cantilevers come from Namiki and Ogura.

Why it matters in a system

A cantilever carries the groove's motion to the shading plate, and every joint and every gram along the way blurs it. Diamond is the stiffest material available for the job, and removing the glue line between stylus and cantilever on the EX removes the last discontinuity. The result is the quietest background and the most secure tracking in the range, which is why the EX is the cartridge against which the others are judged.

What you may hear

The Absolute Sound, naming the Grand Master EX its 2025 Phono Cartridge of the Year, wrote that the new cantilever delivers a silent background reminiscent of tape playback. Of the original Grand Master, Ken Kessler of Hi-Fi News wrote that it may be the best cartridge he had ever heard.

Circuits published, no license feeSince 2021

The open optical-equalizer standard

In February 2021 DS Audio published its optical-equalizer circuit diagrams and offered a free design review to any manufacturer, with no license or consultancy fee. Equalizers from Soulution, EMM Labs, Esoteric, Aavik, Ayre, Soulnote, Westminster Lab and others are now listed by DS Audio as compatible, and any of them will drive any DS Audio cartridge. Read the deep diveClose

What it does

Tetsuaki Aoyagi's stated goal is that optical cartridges move from being unique to being popular, and his route to it was to give the equalizer away. The first third-party unit came in September 2020, when Ed Meitner of EMM Labs designed the DS-EQ1 in direct collaboration with Aoyagi; in February 2021 DS Audio made the program public, releasing its circuit diagrams and promising to review any manufacturer's design free of charge and to list approved products as compatible. Aoyagi has said that manufacturers kept asking what the license fee was, and that he never asked for one, because the market has to be built together and he does not regard other makers as competitors. As of November 2026 DS Audio's compatibility list includes the Soulution 757, shown at Munich in 2023; the Esoteric E1; Aavik's R-880 and R-x88 series; the Engström M-Optic; Reed; EMM Labs' DS-EQ1 and DS-EQ2 and their Meitner Audio versions; Soulnote's E-3 and E-2 ver.2; the Ayre PX-8; the Uesugi UB220R; Phasemation; the Wattson Madison; Westminster Lab's Quest and Monologue; Mavis Lab; the Thivan Labs Ultimate 300; the Exposure 5510; and the Keces S4 and EP+. Michael Trei noted in Stereophile that cartridges and equalizers can now be mixed and matched across brands, and that Meitner will no longer make phono preamps for conventional cartridges.

Why it matters in a system

A cartridge that only works with its maker's phono stage is a closed system; a format with a dozen independent equalizer makers behind it is a third standard beside moving magnet and moving coil. For an owner it means a DS Audio cartridge can be paired with the electronics house whose amplification they already use, and that the choice of equalizer can be made on sound rather than necessity.

What you may hear

Jason Thorpe of SoundStage! wrote that the EMM Labs DS-EQ1 stacks up as one of the best components he had come across; the point of the program is that such a unit and a DS Audio equalizer can be compared on the same cartridge.

All DS Audio technologies and the company story

The DS Audio story

Japanese cartridges that read the groove with light, each with an equalizer to match.

Founded 2013 in Sagamihara, Kanagawa, Japan, where every cartridge is assembled and aligned by Tetsuaki Aoyagi · ds-audio-w.biz

Milestones

  1. 1941 A beam of light Philco's record player reads the stylus with light. In the 1970s Toshiba and other Japanese makers revive the idea, but their lamps run hot and the optical cartridge is set aside when the compact disc arrives.
  2. 2013 DS Audio established Tetsuaki Aoyagi founds DS Audio within Digital Stream Corporation, an optical-engineering firm in Sagamihara, to build an optical cartridge with an LED and modern parts.
  3. 2014 DS-W1 The first DS Audio cartridge to be offered outside Japan.
  4. 2016 Master1 A flagship with a sapphire cantilever, shown at High End Munich.
  5. 2020 Grand Master: the third generation A separate LED and sensor for each channel, a stronger output and a beryllium shading plate.DS Audio Grand Master Equalizer
  6. 2021 The equalizer circuit made public DS Audio publishes its equalizer circuits for any maker to use, without a license fee. The DS 003 brings the third generation to the middle of the range.DS Audio DS 003 Optical Phono Cartridge
  7. 2022 DS-W3 and ES-001 The DS-W3 arrives with a boron cantilever, and the ES-001 shows how far off-center a record sits so that it can be centered.DS Audio DS-W3 Optical Phono Cartridge
  8. 2023 Master3 and Grand Master EX The Grand Master EX is the first cartridge with cantilever and stylus cut from a single diamond.DS Audio Grand Master Extreme Optical Phono Cartridge
  9. 2024 DS-E3 The third generation reaches the first model in the range.DS Audio DS-E3 Optical Phono Cartridge
  10. 2025 TB-100 and the mono cartridges DS Audio's first tube equalizer, and mono versions of the stereo cartridges.DS Audio TB-100 Tube Phono Equalizer
  11. 2026 TB-50 A second tube equalizer joins the range.DS Audio TB-50 Tube Phono Equalizer
Read the DS Audio story
DS Audio

Music on a beam of light

The optical cartridge is older than DS Audio. In 1941 the American maker Philco offered a record player that read the movement of its stylus with a beam of light, and then turned to war work. In the 1970s Toshiba and other Japanese makers revived the idea. Their cartridges were admired for their sound, but the small lamps inside ran hot and made them fragile, and when the industry's attention moved to the compact disc the optical cartridge was set aside.

Tetsuaki Aoyagi

DS Audio takes its initials from Digital Stream Corporation, an optical-engineering firm in Sagamihara, Kanagawa. Tetsuaki Aoyagi was working there, and was not yet a record listener, when he heard an LP played through one of those 1970s Toshiba cartridges. The clarity and life of it surprised him, and he reasoned that the same idea built with modern parts should be better still: a cool-running LED in place of the lamp, and Digital Stream's experience with light sensors behind it. DS Audio was established in 2013, and its first cartridge to reach listeners outside Japan, the DS-W1, followed in early 2014.

How it works

Two questions come up first: does it read the groove with light, and is the signal digital? No to both. A diamond stylus on a cantilever rides the groove exactly as in any cartridge, and the signal stays analog from groove to loudspeaker. The difference is inside. Where a moving-magnet cartridge carries magnets on its cantilever and a moving-coil carries coils of wire, an optical cartridge carries only a tiny shading plate. An LED shines past the plate onto a light sensor, and as the stylus moves, the light reaching the sensor rises and falls with the music.

Two things follow. The moving parts are far lighter, so the stylus is freer to follow the groove. And because the cartridge reads how far the stylus moves, where a magnetic cartridge reads how fast, it needs its own equalizer in place of a phono stage. The cartridge itself mounts and aligns like any other, in most tonearms.

Three generations

The Master1 of 2016, with a sapphire cantilever, was the cartridge that fulfilled the promise of the first design. The third generation began with the Grand Master of 2020: a separate LED and sensor for each channel, a stronger output, and a shading plate of pure beryllium at half the weight of the one before. That design has since come to the whole range, to the DS 003, the DS-W3 and the Master3, and in 2024 to the DS-E3. At the top, the Grand Master EX of 2023 has its cantilever and stylus cut from a single diamond.

An open design

DS Audio's stated aim is to make the optical cartridge a lasting part of record playing, and not only its own product. In 2021 it published its equalizer circuits for any maker to use, without a license fee, and a number of respected electronics makers now build optical equalizers of their own. Any DS Audio cartridge works with any of these equalizers, so the cartridge and the equalizer can be chosen, and later improved, separately. DS Audio's own equalizers now include tube designs, the TB-100 and TB-50.

Made in Sagamihara

Every cartridge is assembled and aligned by hand in Sagamihara, checked under a microscope, and given its own record. The company also makes accessories for record playing, among them a device that shows how far off-center a record sits on the platter so that it can be centered, and an ionizer that removes static.

How they sound

Reviewers return to the same words: clarity, speed and transparency, against a very quiet, black background and without grain. They describe dense recordings opened up so that each instrument has its own place, a deep, three-dimensional picture, and tonal richness with little character added by the cartridge itself.

The complete DS Audio story and technology library

DS Audio at Pearl Audio

Pearl Audio is an authorized DS Audio dealer in Portland. An optical cartridge needs its own equalizer in place of a phono stage, so we choose the two together with you, confirm that the cartridge suits your tonearm, and install and align it ourselves.

The Pearl Audio experience

How we work with you

A system at this level should be heard, thoughtfully matched, and properly set up. From the first audition to long-term ownership, you work with the same people, in person.

  1. 01

    Listen first

    The DS-W3 System is not in our rooms at present. When it is the right piece for a client we arrange a demonstration unit from the manufacturer and set it up for a private session.

  2. 02

    Delivery and installation

    We deliver and install throughout the Portland area, taking care of placement, connections, ventilation and system configuration ourselves.

  3. 03

    Support for as long as you own it

    We support everything we sell for as long as you own it, whether the answer comes by phone, in your home, or through factory service.

  4. 04

    A path for what comes next

    Trade-in assistance and qualifying 100% Trade-Up options give you flexibility when your listening priorities or your system change.

Search