← Back to your LP12 build

Rega · Moving Magnet

Rega Carbon Pro Upgrade Stylus

$100

Upgrade part · All Rega upgrades and parts →

Signature technologiesThe Rega story

Not currently in our rooms. For a serious buyer we will often bring a piece in from the manufacturer for a private session — tell us about your system and what you are weighing it against, and we will advise.

Rega · Moving Magnet

A plug-in elliptical stylus that upgrades your Rega Carbon cartridge in seconds, without taking it off the tonearm.

Upgrade stylus only; the cartridge body is not included.

Plug-in
stylus assembly
Bonded elliptical
diamond
Carbon
body compatibility
2–3 g
tracking force

Authorized Rega dealer · Advice and support from Pearl Audio · Trade-ins welcome

The story

The Carbon Pro replaces the conical stylus on Rega's standard Carbon moving-magnet cartridge with a bonded elliptical diamond. An elliptical tip traces fine groove detail more closely than a conical one, and Rega says the result is an immediate lift in dynamics and detail. It's the simplest upgrade there is for a Planar 1, Planar 1 Plus or Planar 2 with its original Carbon, and it fits a Carbon on any other turntable too.

To fit it, hold the old stylus housing between thumb and forefinger and pull down and toward you. Hook the end of the new stylus into the cartridge at a slight angle, then push up until it clicks into place. Track it at 2–3 g, the same as the original.

The Carbon Pro is the upgrade stylus for the Carbon; the standard Carbon Stylus ($50) restores the original conical tip. When you want more than a Carbon can give, the Nd3 is the next full step.

The Carbon is the entry point to Rega's cartridge range on the Planar 1 and Planar 1 Plus, and the Nd3 of 2024, the first moving magnet built on an N55 neodymium magnet, is the step above it. Read the Rega story →

Key technologies

  • Bonded elliptical diamond. Traces fine groove detail more closely than the Carbon's conical tip, for a lift in dynamics and detail.
  • Plug-in fitting. Hook the new stylus in at a slight angle and push up until it clicks; no need to remove the cartridge.
  • Fits any Carbon. On a Planar 1, Planar 1 Plus, Planar 2 or any other turntable with a Carbon.
  • Genuine Rega part. Supplied through The Sound Organisation, Rega's US distributor.

The Carbon is the cartridge it fits; the Carbon Stylus restores the original tip, and the Nd3 is the next cartridge up.

Specifications
Fits Rega Carbon MM cartridge (Planar 1, Planar 1 Plus, Planar 2 and others)
Stylus Bonded elliptical diamond
Tracking force 2–3 g
Installation Plug-in; no need to remove the cartridge

Rega Carbon Pro Upgrade Stylus product page and specifications

Rebuilds and trade-in

Rega publishes no trade-in program for this product; the factory service that applies is listed below. Ask us about trade-ins.

Carbon Pro Upgrade Stylus (this product) $100 (plug-in stylus for the Rega Carbon moving-magnet cartridge)

A plug-in stylus is the service for the Rega Carbon; no trade-in program applies. Verified 2026-10-28. Source: Rega pricing catalog v2025.1, October 2025 (The Sound Organisation) and soundorg.com/cartridge-exchange.

Where it sits in the range

The Rega cartridges Pearl Audio stocks:

  • Rega Carbon Stylus: replacement conical stylus for the Carbon
  • Rega Carbon: entry MM with plug-in stylus, 2.5 mV
  • Rega Carbon Pro Upgrade Stylus (this model)
  • Rega Nd3: entry Nd moving magnet, bonded elliptical
  • Rega Nd5: nude elliptical Nd, faster and tighter
  • Rega Nd7: fine-line Nd moving magnet
  • Rega Ania: entry Rega MC, hand-wound, elliptical, 0.35 mV
  • Rega Nd9: top Nd, boron cantilever, Rega arms only
  • Rega Ania Pro: Ania with the Vital nude diamond, 0.35 mV
  • Rega Apheta 3: hand-built Rega MC, Aphelion stylus technique, 0.35 mV
  • Rega Aphelion 2: reference Rega MC, boron cantilever, 0.35 mV

Plan your Rega system with Pearl Audio

Pearl Audio is an authorized Rega dealer. Ask us to confirm the fit for your cartridge before ordering, or have us fit it in our Portland showroom. Call (503) 222-2599 or email sales@pearlaudio.com.

Signature technologies

The engineering behind the Rega Carbon Pro Upgrade Stylus

Rega gives its technologies names because each one solves a specific problem. Here is what each does, where it came from, why it matters in a system, and what you may hear.

From the RB300 of 1983 to the RB TitaniumSince 1983

The one-piece cast RB tonearm

In 1983 Rega introduced the RB300, whose headshell and arm tube are one tapered aluminum casting with no joints, on preloaded ball-bearing gimbals. The same lineage runs through the RB110, RB220, RB330, RB880, RB3000 and RB Titanium today; the higher the model, the tighter the bearing fit and the fewer the joints. Counting OEM versions, the family has sold more than 400,000. Read the deep diveClose

What it does

The RB300 of 1983 replaced the Acos-made R200 with a tapered, one-piece cast aluminum tube running unbroken from headshell to pivot, a tungsten-alloy counterweight and a tracking-force spring; Rega worked with a casting company to develop a method for casting so long a cored hole accurately. The RB250 followed in 1984, the RB301 in 2007 and the RB303 in 2011. The current arms share one geometry, a 222 mm mounting distance, 236.5 mm effective length, 21.55 degree offset and 11 g effective mass, and differ in bearings and materials. The RB110 on the Planar 1 and the RB220 on the Planar 2 and Planar 78 use Rega's patented ultra-low-friction polymer bearings with automatic bias. The RB330 of 2016 has hand-selected ball bearings preloaded by one or two microns with no measurable free play and a tube with its mass redistributed. The RB880 of 2019 adds a stainless-steel sleeve and shaft and hand-matched bearings; the RB3000 is hand-polished, with bearings an interference fit on the spindle and no adhesive anywhere; the RB Titanium of 2023 has a one-piece titanium bearing housing and spindle and a tungsten counterweight. Gandy has said standard bearings run at about one micron of clearance after preloading and the best arms at less than one micron. Rega makes arms for about twenty other brands.

Why it matters in a system

The arm holds the cartridge still while the groove moves it, and any play in the bearings or flex at a joint is information lost. Rega's position is that such losses can never be recovered later in the chain, which is why the arm is where it spends the money, and why there is no VTA adjustment: a 2 mm spacer under the arm base does that job without a loose joint.

What you may hear

A UK retrospective called the RB300 "one of the most important tonearms of its generation, perhaps even ever." What an RB arm gives a cartridge is a stable platform, which listeners hear as secure tracking, solid images and bass that does not blur.

Moving-coil behavior at moving-magnet outputSince 2024

The Nd neodymium moving magnets

The Nd3, Nd5, Nd7 and Nd9 are the first moving-magnet cartridges built around an N55 neodymium magnet, the strongest commercial grade. The strong magnet allows very small coils, which gives low inductance and impedance, a wider high-frequency response and better channel balance, with a 5 to 6 millivolt output that any MM phono stage can use. All four share the generator and differ in stylus and cantilever. Read the deep diveClose

What it does

Rega says the Nd generator was developed over ten years. Its coils are wound from 38-micron wire with 1,275 turns, far fewer than a conventional moving magnet needs, because the N55 magnet supplies the field; the body is glass-filled PPS, tracking force 1.75 grams, and a pivot-pad design removes the mechanical joint between stylus housing and body, so instead of a user-replaceable stylus Rega offers a factory rebuild with a new cantilever, stylus and pivot pad. The Nd3 of May 2024 carries a bonded elliptical polycrystalline diamond on a titanium shank behind a red window; the Nd5 of June 2024 a nude elliptical diamond; the Nd7 of July 2024 a nude monocrystalline fine-line diamond, 3 by 30 microns, the profile of the Apheta 3 and Aphelion 2; all three on aluminum cantilevers. The Nd9 of November 2025 moves to a boron rod cantilever, joined by a connecting tube made with a watchmaker because the generator was designed around aluminum, and Rega calls it the highest-performing moving magnet it has produced. The range has replaced the Elys and Exact as Rega's factory-fitted cartridges: the Nd3 on the Planar 2 and 3, the Nd5 on the Planar 3, 3 RS and 6, the Nd7 on the Planar 6 and 8, and the Nd9 on the Planar 6 RS and 8.

Why it matters in a system

For most systems the Nd range is where a Rega turntable upgrade starts, because it works with the moving-magnet phono stage built into every Rega integrated and the Fono MM MK5, with no change of gain or loading. The Nd7 in particular is pitched by reviewers against moving coils at its price.

What you may hear

Jason Kennedy: "I would suggest that those looking for next level results with vinyl consider the Nd7 before an MC." Ed Selley of AV Forums found the Nd3 brings "some of the sheer energy that the moving coil designs deliver down a much lower price point."

Nothing superfluous in the signal pathSince 2018

Discrete and FET phono stages: Fono, AOS and Aura

The Aura of 2018 is a fully symmetrical, three-stage, all-Class-A moving-coil phono stage with graded Linear Systems FETs at its input, so no bias current flows through the cartridge coil. The AOS MC of 2026 is a two-stage, half-width derivative of the same circuit, the Fono MC MK4 applies the FET input in a compact box, and the Fono MM MK5 is the discrete moving-magnet stage that What Hi-Fi? has named a winner every year since 2018. Read the deep diveClose

What it does

Gandy credits the Aura largely to Rega's chief electronics designer, Terry Bateman. It uses passive RIAA equalization at high frequencies and active at low, a power supply running about 60 percent higher in voltage than typical for headroom, balanced XLR and single-ended outputs, switchable gain of 63.5 or 69.5 dB, loading from 50 to 400 ohms and 1,000 to 5,700 pF, and relays for mono and mute; it weighs 13 kg. Rega says it avoided any superfluous functions because they obstruct the signal path. The AOS MC of February 2026 takes a symmetrical complementary Class A FET first stage driving passive high-frequency RIAA and a Class A differential second stage, with no digital control circuitry, a self-adjusting thermal servo and the same loading options, in a half-width case. The Fono MC MK4 of 2021 uses the Linear Systems LSK389 FET in an all-discrete input stage with MUSES op-amps for RIAA, DIP-switch loading and a factory default that suits every Rega moving coil. The Fono MM MK5 of 2021 has a fully discrete, cascaded complementary input, two-stage RIAA, 41.4 dB of gain and 47 kilohm, 100 pF loading; its internals are unchanged from the MK4. The Fono Mini A2D MK2 of 2019 adds a USB output for recording records.

Why it matters in a system

A phono stage amplifies the smallest signal in a system by a thousand times or more, and Rega's FET inputs keep that first stage quiet and keep the cartridge coil free of DC. The MM stages match the Nd range and the MC stages are set up for the Ania, Apheta 3 and Aphelion 2 out of the box, which keeps a Rega chain simple to assemble.

What you may hear

What Hi-Fi? wrote that "The Aura's clarity is class leading, as is the way it renders the dynamic envelope of instruments"; Paul Messenger of hi-fi+ found it "more than justifies its price." Jason Kennedy said the AOS MC "has perfect timing," and What Hi-Fi? called the Fono MM MK5 "the one to beat at this level."

All Rega technologies and the company story

The Rega story

Southend-on-Sea since 1973: low-mass turntables, one-piece cast tonearms and hand-built cartridges, made in England.

Founded 1973 in Southend-on-Sea, Essex, England, where every Rega is still built by Roy Gandy and Tony Relph · rega.co.uk

Milestones

  1. 1973 Rega Research registered; the Planet Ford-trained engineer Roy Gandy and Southend hi-fi dealer Tony Relph each put in 1,000 pounds and register the company on July 1, 1973, named from RElph and GAndy. The first turntable, the Planet, has a three-spoke metal platter and an Acos Lustre arm.
  2. 1976 Planar 3, then Planar 2 The Planar 3 of April 1976 introduces the 12 mm glass platter and the R200 arm, and is lighter than the Planet; the Planar 2 with a 10 mm glass platter follows in April 1977. The low-mass, high-rigidity philosophy begins here.Rega Planar 2
  3. 1983 RB300 A tonearm with headshell and tube cast as one tapered piece of aluminum, on preloaded ball bearings, with a tungsten-alloy counterweight. The RB250 follows in 1984; with OEM versions, the family sells more than 400,000.Rega RB330 Tonearm
  4. 1988 Cartridges made in-house The Elys and Bias, launched in 1987 with Rega's three-point mounting, go into in-house production in March 1988 and sell over 1,000 in the first month. The hand-wound Exact follows in 1992.
  5. 1991 Elicit, Brio and Elex After the clam-shell Elicit of 1990, the Brio and Elex integrated amplifiers of April 1991 begin the Class A/B lineage that runs to today's Brio MK7 and Elex MK4. Gandy designs a factory on the Temple Farm Industrial Estate for loudspeaker and amplifier production.Rega Brio Mk7 Integrated Amplifier
  6. 1995 Planar 9: the ceramic platter The first Rega with a ceramic platter and an external power supply, with the RB900 arm. The Kyte loudspeaker precedes it in 1993 and the Planet CD player follows in 1997.Rega Planar 10
  7. 2005 Apheta Rega's first moving-coil cartridge, with hand-wound coils on an iron micro-cross and no tie wire or damper: the design behind today's Ania, Apheta 3 and Aphelion 2.Rega Apheta 3 MC Cartridge
  8. 2009 The reference range The Ios phono stage in February, the Osiris integrated amplifier in May and the Isis and Isis Valve CD players in June. Work on the Naiad research turntable begins the same year.Rega Osiris Reference Integrated Amplifier
  9. 2013 RP8 and RP10: the skeletal plinth The RP8 of July 2012 cuts the plinth to a skeleton with a three-part flywheel glass platter; the RP10 of October 2013 adds a ceramic platter and a DSP-generated power supply. The RP3 is Stereophile's 2012 Analog Source Component of the Year.
  10. 2016 The new Planar 3 After two years of development led by Gandy, a Planar 3 carrying over just two components from the RP3: double-braced plinth, 12 mm Optiwhite glass and the new RB330. The Planar 1, Planar 2 and Brio are renewed the same year.Rega Planar 3
  11. 2017 Planar 6 and the Naiad The Planar 6 is the first Rega with a Tancast 8 foam-core plinth and the Neo power supply. The Naiad, built to push Rega's philosophies to the extreme, is limited to 50 units. The Ania moving coil and RB220 follow.Rega Planar 6
  12. 2019 Planar 10, Apheta 3 and Aethos The Planar 10 brings the ceramic platter, ceramic top brace and RB3000 to a skeletal foam-core plinth; the Planar 8 preceded it in October 2018, and the Aura phono stage in June 2018. The Aethos integrated amplifier arrives in November.Rega Planar 10
  13. 2023 Fifty years; the Naia A Planar 3 50th Anniversary Edition in May and, in September, the Naia: the production form of the Naiad, with a graphene-impregnated carbon-fiber plinth, ceramic braces and platter, a ZTA ceramic bearing and the RB Titanium.Rega Naia Reference Turntable
  14. 2024 The Nd range and employee ownership The Nd3, Nd5 and Nd7 are the first moving magnets built on an N55 neodymium magnet; the Planar 3 RS follows in November. On October 28, 2024, Roy Gandy gifts 100 percent of his shares to an Employee Ownership Trust and remains sole director.Rega Nd7 MM Cartridge
  15. 2025 Brio MK7, Mercury and Solis, Nd9 The seventh Brio in March; the Mercury preamplifier and Solis power amplifier, four years in development, in November, with the boron-cantilever Nd9. On November 17, 2025, What Hi-Fi? gives Gandy its Outstanding Contribution Award.Rega Nd9 Reference MM Cartridge
  16. 2026 AOS MC, Planar 6 RS and Replay The AOS MC phono stage, derived from the Aura, in February; the Planar 6 RS with the RB880 and Nd9 in March; the plug-and-play Replay in October. Rega employs over 150 people on one industrial estate in Southend-on-Sea.Rega Planar 6 RS Edition Turntable
Read the Rega story
Rega

Roy Gandy trained as a mechanical engineer at the Ford Motor Company and made loudspeakers in his spare time because he could not afford to buy a hi-fi; his first system used homemade speakers and a turntable he designed himself from salvaged and discounted parts. He had tinkered with machinery since the age of four, rebuilt bicycles and motorbikes and built two motorcycles from scratch, and the hand-built equipment he sold to friends led to supplying a local Southend audio shop. The shop's owner, hi-fi dealer Tony Relph, saw potential in the turntables and suggested a company; each partner put in 1,000 pounds, and Rega Research was registered on July 1, 1973, named from the first letters of RElph and GAndy. Rega's own timeline dates its first turntable, the Planet, to April 1973, with a three-spoke steel and aluminum platter and an Acos Lustre tonearm; Gandy says it sold because it looked different rather than on sound quality. The partners worked above the shop at first, then in a house Gandy gutted to make a factory.

The Planar of April 1975, with an aluminum platter, ran to only 200 units. The Planar 3 of April 1976 replaced the Planet's three metal discs with a 12 mm glass platter, which Gandy called a big step forward, and was lighter than the Planet; it carried the Acos-made R200 tonearm. The Planar 2, with a 10 mm glass platter, followed in April 1977, the year Hi-Fi News and Record Review remarked of the Planar 3 that the complete unit was worth a look. Turntable production moved into a converted mill on Park Street in Westcliff-on-Sea, and 1980 brought the R100 moving-magnet cartridge and the RTX floor-standing loudspeaker. In April 1983 came the RB300, whose headshell and arm tube are one tapered aluminum casting with no joins, a tungsten-alloy counterweight and a spring for tracking force; Rega had worked with a casting company on a new method of casting so long a cored hole. The RB250 followed in 1984. Counting every variant and the OEM arms Rega has made for NAD, Rotel and about twenty other brands, the RB300 family has sold more than 400,000.

The RB100 cartridge of 1985 was designed by Rega and made with Goldring, and the Planar 78 appeared the same year. The Elys and Bias cartridges followed in 1987, and by March 1988 Rega was building them in-house, selling over 1,000 in the first month. Electronics came next: the clam-shell Elicit integrated amplifier in May 1990, the Brio and Elex in April 1991, and the hand-wound, three-point-mounted Exact cartridge in April 1992. Gandy designed a factory on the Temple Farm Industrial Estate in Southend-on-Sea to house loudspeaker and amplifier production; the Kyte bookshelf loudspeaker arrived in September 1993, the Planar 9 with a ceramic platter and external power supply and the RB900 arm in 1995, and the Planet CD player in June 1997. Rega has advertised only once and puts the money into research instead. By 2000 the range had been renamed P2 and P3 2000, and the 24 V motor board and the first TTPSU outboard supply arrived in 2001.

The P5, P7 and P9 of 2002, the latter two with ceramic platters, brought the RB700 and RB1000 arms; the Apollo and Saturn CD players arrived in 2004, the first Apheta moving-coil cartridge in March 2005 and the P1 that June, and the three-point RB301 and P3-24 in 2007. In 2009 Rega launched a reference range: the Ios phono stage in February, the Osiris integrated amplifier in May and the Isis and Isis Valve CD players in June. The RP1 of 2010 introduced the phenolic-resin platter, the RP3 and RP6 followed in 2011, and the RP3 won Stereophile's Analog Source Component of the Year for 2012. The RP8 of July 2012 brought the skeletal plinth and a three-part flywheel glass platter, the RP10 of October 2013 the skeletal plinth with a ceramic platter, and 3,000 RP40 anniversary decks marked forty years. The Apheta 2 came in 2014 and the Aphelion in 2015. Around 2013 Rega employed almost 90 people and made about 2,000 turntables a month; the Temple Farm site was expanded with a new building and mezzanine in 2014 and 2015, and the Naiad, a research project begun in 2009, was shown to visitors in 2015.

In 2016 Rega rebuilt its entry decks: the Planar 2 in May, the Planar 1 in July, the RB330 in August and in October a Planar 3 that carried over just two components from the RP3 after two years of work led by Gandy. The Neo power supply, Planar 1 Plus, Planar 6, Ania and RB220 followed in 2017, along with the Naiad, built to push Rega's philosophies to the extreme in a run of 50. The Aura phono stage, largely the work of chief electronics designer Terry Bateman, came in June 2018 and the Naiad-inspired Planar 8 that October; 2019 brought the RB880, Apheta 3, Planar 10 and Aethos; 2020 the Ania Pro, Aphelion 2 and io. Staff numbered 140 by 2020, with output of several thousand turntables a month. The Kyte returned in 2021 with the Fono MM MK5, Fono MC MK4 and Neo MK2, the Elicit MK5 and Elex MK4 arrived in 2022, and in 2023 Rega marked fifty years with a Planar 3 50th Anniversary Edition in May and, in September, the Naia, the production form of the Naiad, and the AYA loudspeaker.

The Nd3, Nd5 and Nd7 of 2024 were the first moving-magnet cartridges built on an N55 neodymium magnet, and the Planar 3 RS, RS standing for Rega Special, followed in November. On October 28, 2024, Roy Gandy gifted 100 percent of his shares to an Employee Ownership Trust, taking no financial gain; every employee became a beneficiary, the trust is barred from selling the company, and Gandy remains sole director, working in research and sales. The Brio MK7 arrived in March 2025, the Mercury preamplifier, Solis power amplifier and Nd9 in November 2025, and on November 17, 2025, What Hi-Fi? gave Gandy its Outstanding Contribution Award. The AOS MC phono stage came in February 2026, the Planar 6 RS in March and the Replay in October. Rega today employs over 150 people, designs and hand-assembles every product in custom-built facilities on one industrial estate in Southend-on-Sea totaling almost 70,000 square feet, exports to more than fifty countries and backs every product with a lifetime limited warranty against manufacturing defects. Phil Freeman is managing director, and the United States is served through The Sound Organisation in Arlington, Texas.

The complete Rega story and technology library

Rega at Pearl Audio

Pearl Audio is an authorized Rega dealer in Portland. We carry the range from the Planar 1 to the Naia, the RB tonearms, the Nd and moving-coil cartridges, the io through Osiris amplifiers and the Mercury and Solis, the Fono, AOS and Aura phono stages, the Isis players and the Kyte, and we order factory-fitted turntable and cartridge combinations to suit the rest of your system. Our staff set up and level Rega turntables, fit and align cartridges, set tracking force, and match decks, phono stages and amplifiers to your loudspeakers and your room. We are here for upgrades, from a Neo power supply or a new cartridge to the next deck up.

Ownership

Rebuilds, exchange and trade-in

Rega cartridges can be returned to the maker for service rather than replaced outright. We handle the paperwork and shipping.

Factory rebuild and retip

ServicePrice
Carbon Pro Upgrade Stylus (this product)plug-in stylus for the Rega Carbon moving-magnet cartridge $100

A plug-in stylus is the service for the Rega Carbon; no trade-in program applies. Verified 2026-10-28. Ask us about trade-ins.

Pricing per Rega - 2025-Fall - Price Sheet (The Sound Organisation, October 2025) and soundorg.com/cartridge-exchange/. Programs are set by the manufacturer and may change.

The Pearl Audio experience

How we work with you

A system at this level should be heard, thoughtfully matched, and properly set up. From the first audition to long-term ownership, you work with the same people, in person.

  1. 01

    Listen first

    The Carbon Pro Upgrade Stylus is not in our rooms at present. When it is the right piece for a client we arrange a demonstration unit from the manufacturer and set it up for a private session.

  2. 02

    Placement and setup advice

    Ask us about placement, connections, ventilation and system configuration, and about delivery.

  3. 03

    Support for as long as you own it

    We support everything we sell for as long as you own it, whether the answer comes by phone, in the shop, or through factory service.

  4. 04

    A path for what comes next

    Trade-in assistance and qualifying 100% Trade-Up options give you flexibility when your listening priorities or your system change.

Search