← Back to your LP12 build

T+A Elektroakustik · Series 200

T+A Elektroakustik T+A A 200 Stereo Power Amplifier

$6,750

Signature technologies

Not currently in our rooms. For a serious buyer we will often bring a piece in from the manufacturer for a private session — tell us about your system and what you are weighing it against, and we will advise.

T+A Elektroakustik · Series 200

The A 200 is a 32 cm wide stereo power amplifier that pairs PURIFI Eigentakt output stages with T+A's own high-voltage input circuitry and a sine-wave power supply: 125 W into 8 Ω, 250 W into 4 Ω, 5 kg.

125 W
per channel into 8 Ω (250 W into 4 Ω)
> 800
damping factor
113 dB
signal-to-noise
5 kg
11 lb

Authorized T+A Elektroakustik dealer · Delivery and installation by Pearl Audio · Trade-ins welcome

The story

T+A's Series 200 amplifiers use PURIFI's Eigentakt Class D output stages, which the company chose because they remove the load dependence and distortion that marked earlier switching amplifiers. What makes the A 200 a T+A amplifier is what sits in front of them: a voltage amplifier stage built with the HV-Series' high-voltage circuit topology, so the input and driver stages are linear without heavy feedback, and a high-frequency sine-wave mains section instead of a conventional switching supply, with reservoir capacitors recharged 100,000 times a second.

The result on paper is a damping factor above 800, distortion below 0.002 % and a 113 dB signal-to-noise ratio from a 5 kg box. Intelligent Safe Control, a microcontroller watching temperature, load and clipping, intervenes only when something leaves its permitted range. Inputs are RCA and XLR.

Driven by the DAC 200 as preamplifier, the A 200 completes a two-box Series 200 system; if you need more power or want mono separation, the M 200 monoblocks use the same platform. We can arrange an audition in our Portland showroom and help with system matching, delivery and setup.

The Series 200 was announced on September 17, 2021, with the A 200 pairing PURIFI Eigentakt output stages with the HV voltage stage T+A had developed for its High Voltage series of 2013. It arrived a month after the company set up T+A North America in St. Marys, Georgia, and like every T+A it is designed, built and measured in Herford. Read the T+A story →

Key technologies

  • PURIFI Eigentakt output stages. Class D modules chosen for low distortion and load independence.
  • HV input circuitry. T+A's high-voltage topology in the voltage amplifier stage, without hard feedback.
  • Sine-wave mains section. Pure sine-wave supply at more than twice conventional switching frequency, recharging the reservoir 100,000 times a second.
  • Intelligent Safe Control. Microcontroller monitoring of temperature, load and clipping.

The DAC 200 is the A 200's preamplifier; the M 200 monoblocks are the step up in power.

Finishes

  • Alu silver anodized (43)
  • Alu black anodized (42)
Specifications
Type Stereo power amplifier, Class D (PURIFI Eigentakt) with HV input stage
Power output 125 W into 8 Ω, 250 W into 4 Ω (per channel)
Frequency response 1 Hz – 60 kHz (+0/–3 dB)
Distortion < 0.002 % THD and intermodulation
Signal-to-noise 113 dB
Damping factor > 800 (DF LO setting > 70)
Inputs RCA 800 mV / 5.8 kΩ; XLR 1.6 V / 20 kΩ
Dimensions (H × W × D) 10 × 32 × 34 cm (3.9 × 12.6 × 13.4 in)
Weight 5 kg (11.0 lb)
Finishes Alu silver anodized (43) or alu black anodized (42)

T+A A 200 product page and specifications

Where it sits in the range

Series 200 is T+A's compact line. Siblings, least to most expensive:

The DAC 200 is the matching preamplifier and converter.

Plan your T+A system with Pearl Audio

Pearl Audio is an authorized T+A dealer. We can arrange an audition in our Portland showroom and help with system matching, delivery and setup. Call (503) 222-2599 or email sales@pearlaudio.com.

Signature technologies

The engineering behind the T+A Elektroakustik T+A A 200 Stereo Power Amplifier

T+A Elektroakustik gives its technologies names because each one solves a specific problem. Here is what each does, where it came from, why it matters in a system, and what you may hear.

Transistors run where they are most linearSince 2013

HV: high-voltage amplifier stages

T+A's HV circuits run their transistor voltage-gain stages on supply rails several times higher than ordinary solid-state designs, up to 100 V in the P 3100 HV preamplifier and up to 500 V in the M 40 HV's power stages. Each device then works over a small, linear part of its curve, as a tube does, so the circuit needs virtually no overall negative feedback. Read the deep diveClose

What it does

Most solid-state audio circuits run on low rails; Alan Sircom notes that most modern circuits run at about plus and minus 5 V. The High Voltage series, three years in development and introduced in 2012 by Siegfried Amft's account or 2013 by T+A's own, moved the voltage-gain stages to rails several times higher, with the stated aim of combining the sonic and technical advantages of tubes and transistors while avoiding the inherent disadvantages of present-day valves. In the PA 3100 HV the input is a differential cascode amplifier of individually selected audio J-FET transistors that can process signals up to 60 V peak-to-peak without distortion; the P 3100 HV runs at up to 100 V and handles 80 V peak-to-peak; the M 40 HV's power stages reach 500 V, behind a class-A input stage of 6SN7 triodes. Because each transistor works over a small, linear part of its curve, the circuit needs virtually no overall negative feedback, and bandwidth and headroom are wide: the P 3100 HV is specified from 0.5 Hz to 300 kHz. HV is used in the amplifier stages of every HV-series component, the same voltage-gain stage appears in the Series 200, the HA 200 and the Symphonia, and the PA 2500 R and PA 2000 R carry a high-voltage dual-mono design on the R-series chassis.

Why it matters in a system

An amplifier stage that stays linear without heavy feedback behaves the same from the first watt to clipping and into awkward loudspeaker loads, which is what HV owners describe as ease at volume. It is also the reason a T+A preamplifier, converter and power amplifier sound of a piece: the same voltage-gain stage sits in all of them, from the DAC 200 to the M 40 HV.

What you may hear

Jason Victor Serinus, reviewing the PA 3100 HV for Stereophile, found the midrange strong, exceptionally smooth, and all of one piece. Alan Sircom in hi-fi+ called the SDV 3100 HV extremely listenable, with extraordinary clarity and dynamics, and musically inviting.

Class D with a high-voltage gain stage and sine-wave suppliesSince 2021

PURIFI Eigentakt output stages with an HV front end

For its compact amplifiers T+A pairs licensed PURIFI Eigentakt class-D output modules with its own HV voltage-gain stage and a switch-mode power supply that runs a sine-wave clock at more than twice the usual frequency. The A 200 makes 125 W into 8 ohms and 250 W into 4 from a 5 kg chassis, with a damping factor above 800. Read the deep diveClose

What it does

The Series 200 of September 2021 needed HV-series behavior in a chassis 32 cm wide, and T+A's answer was to keep its own circuit where it matters most. The voltage-amplifier stage, the part that sets an amplifier's character, is T+A's HV circuit, which the company describes as unique in the world; the output stage is PURIFI's Eigentakt class-D module. The power supply is T+A's own: a high-frequency sine-wave mains section, described by T+A as a hard supply, whose reservoir capacitors are recharged 100,000 times per second rather than at the mains frequency. The A 200 delivers 125 W into 8 ohms and 250 W into 4; the M 200 mono delivers 210 and 420 W from the same topology; each weighs 5 kg and both are designed around the DAC 200 and HA 200 as a system. The Symphonia of 2025 uses in-house modifications of the Eigentakt technology for 125 W per channel in a retro-styled streaming integrated 38 cm wide with analog VU meters, a phono input and HDMI ARC. The R-series PA 2500 R and R 2500 R keep class-AB output stages but share the HF sine-wave supply, the PA 2500 R carrying two of them with 120,000 µF of storage.

Why it matters in a system

Class D makes it possible to put real power behind a pair of floorstanders in a system the size of a bookshelf, and the objections to it have mostly concerned the input stage and the power supply, which are the two parts T+A kept for itself. The result is a power amplifier that partners the DAC 200 or the HA 200 as a system without a second rack.

What you may hear

John Darko on the Symphonia: an exceedingly competent amplifier that performs on par with similarly priced competition, and a product for tighter spaces and minimalists. Stereophile, quoted by T+A, called it a miniature Meisterstück that delivers more audiophile gravitas than its size suggests.

Theory and application under one roofSince 1978

Designed, built and measured in Herford

Every T+A component is designed, assembled and measured at the company's own buildings in Herford, where it has been since 1988: circuit design, board layout, software, the MusicNavigator app, final assembly and a measurement protocol for every unit. Surface-mount board assembly is placed with a specialist using T+A-supplied parts; about 95 percent of production is in-house. Read the deep diveClose

What it does

T+A has occupied its own buildings in Herford since 1988 and added an administration, sales and laboratory building in 2003. A factory visit in April 2025 counted about 90 employees, 14 of them in research and development; T+A itself describes a team of fifteen designers and developers plus seven service technicians. The scope kept in-house runs from design, PCB layout and certification to assembly, measurement, operating-system programming and app development; the one step placed outside is surface-mount component placement, done by a specialist assembler using components T+A supplies, after which the boards return for final assembly and test. There are no assembly lines or automated placement machines, and nothing leaves the works without a measurement protocol. The company's own description is that it builds acoustic treasures rather than mass products, and it reports returning more than 98 percent of devices of any age to working condition when they come back for service. The engineering continuity is long: Lothar Wiemann, who joined as a student and developed the first electronics in 1982, was chief developer for 39 years before handing over to Jörg Küpper. In the United States, T+A North America in St. Marys, Georgia has handled distribution since August 2021, with service through Pyramid Audio in Austin and Audio Design and Service in Burbank.

Why it matters in a system

A product made in one place by the people who designed it can be supported for as long as its owner wants to keep it, and T+A's factory upgrades, the ASA G3 streaming boards fitted to players from 2017, are the practical form of that. It is also why a T+A system sounds consistent from the Series 200 to the HV line: the same small team designed all of it.

What you may hear

Jim Austin, in Stereophile on the MP 3100 HV: more than any other component he had had in his system, it radiated attention to detail. Michael Manousselis, who imported the brand to North America: they don't leave things to luck or to chance.

The Pearl Audio experience

How we work with you

A system at this level should be heard, thoughtfully matched, and properly set up. From the first audition to long-term ownership, you work with the same people, in person.

  1. 01

    Listen first

    The T+A A 200 Stereo Power Amplifier is not in our rooms at present. When it is the right piece for a client we arrange a demonstration unit from the manufacturer and set it up for a private session.

  2. 02

    Delivery and installation

    We deliver and install throughout the Portland area, taking care of placement, connections, ventilation and system configuration ourselves.

  3. 03

    Support for as long as you own it

    We support everything we sell for as long as you own it, whether the answer comes by phone, in your home, or through factory service.

  4. 04

    A path for what comes next

    Trade-in assistance and qualifying 100% Trade-Up options give you flexibility when your listening priorities or your system change.

Search